• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




RUBBER AND PLASTICS HOSES AND HOSE ASSEMBLIES - METHODS OF MEASUREMENT OF DIMENSIONS (ISO 4671:1999, IDT)
MS ISO 4671:2007
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies methods of measuring the inside diameter, outside diameter (including diameter over reinforcement of hydraulic hoses), wall thickness, concentricity, and lining and c ....Read more over thickness of hoses, methods of measurement and identification of the length of hoses and hose assemblies, and a method of verifying the through-bore of hydraulic hose assemblies. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



Rubber, vulcanized - Determination of temperature rise and resistance to fatigue in flexometer testing - Part 3: Compression flexometer (constant-strain type) (First revision) (ISO 4666-3:2010, IDT)
MS ISO 4666-3:2012
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies the flexometer test with constant-strain amplitude for the determination of the temperature rise and resistance to fatigue of vulcanized rubber. The flexometer specif ....Read more ied is known as the Goodrich flexometer, but any other apparatus giving equivalent performance can be used. 
This Malaysian Standard gives directions for carrying out measurements which make possible predictions regarding the durability of rubbers in finished articles subject to dynamic flexing in service such as tyres, bearings, support, V-belts, and cable-pulley insert rings. However, owing to the wide variations in service conditions, no simple correlation between the accelerated tests described in the various parts of this standard and service performance can be assumed.

The method is not recommended for rubber having a hardness greater than 85 IRHD. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



Rubber, vulcanized - Determination of temperature rise and resistance to fatigue in flexometer testing - Part 1: Basic principles (ISO 4666-1:2010, IDT)
MS ISO 4666-1:2012 (CONFIRMED:2025)
Status : 2nd Confirmation
Format : PDF

This Malaysian Standard establishes general principles for flexometer testing and defines the terms used. Flexometer testing makes possible predictions regarding the durability of rubbers in finished ....Read more articles subject to dynamic flexing in service such as tyres, bearings, supports, V-belts, and cable-pulley insert rings. However, owing to the wide variations in service conditions, no simple correlation between the accelerated tests specified in the various parts of this standard and service performance can be assumed. Close

RM 30.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized or thermoplastic - Resistance to weathering (First revision) (ISO 4665:2006, IDT)
MS ISO 4665:2013
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies methods for the exposure of vulcanized or thermoplastic rubbers to natural or artificial weathering and methods for the determination of changes in colour, appearance ....Read more and physical properties resulting from exposure. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



Rubber, vulcanized or thermoplastic - Determination of rebound resilience (First revision) (ISO 4662:2009, COR. 1:2010, IDT)
MS ISO 4662:2013
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies two methods for determining the rebound resilience of rubber the hardness of which lies between 30 IRHD and 85 IRHD. They are the pendulum method and the tripsometer ....Read more method. 
With the pendulum method, a mass with a spherical end impacts a flat test piece, firmly held but free to bulge. The kinetic energy of the impacting mass is measured immediately before and after impact.

With the tripsometer method, a flat test piece is impacted by a hemisphere mounted on the periphery of a disc which is supported on an axle and caused to rotate by an off-axis mass. The kinetic energy of the impacting mass is measured immediately before and after impact. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



METHODS OF TEST FOR VULCANIZED RUBBER: PART 40/1: DETERMINATION OF ABRASION RESISTANCE USING A ROTATING CYLINDRICAL DRUM DEVICE (FIRST REVISION) (ISO 4649:2002, IDT)
MS ISO 4649:2005
Status : Withdrawn
Format : PDF

This standard specifies two methods for the determination of the resistance to abrasion by means of rotating cylindrical drum devices. The methods involve determination of volume loss due to abrasive ....Read more action of rubbing a test piece over a specified grade of abrasive sheet. Method A is for a non-rotating test piece and method B for a rotating test piece. Foreach method, the result can be reported as a relative volume loss or an abrasion resistance index. 
NOTE1 Users of previous editions of this International Standard should be aware that methodA and methodB in this editionhave been changed. In this edition, methodA (non-rotating test piece) with the calculation of relative volume loss (see3.2)corresponds to methodA of the previous editions. MethodA (non-rotating test piece) and methodB (rotating test piece) withcalculation of abrasion resistance index (see3.3) were both included in methodB in the previous editions.

Because factors such as the grade of abrasive sheet, the type of adhes Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



Rubber, vulcanized - Determination of static adhesion to textile cord - H-pull test (First revision) (ISO 4647:2010, IDT)
MS ISO 4647:2013
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies a method for the determination of the static adhesion of textile cord to vulcanized rubber using the H-pull test. It is applicable to cords made from natural or man-m ....Read more ade fibres. 
The property levels obtained with this method are affected considerably by the history of the cord and the rubber compound. The method yields data, however, on which a judgement as to the service quality of the material can be based.

The method is primarily intended for use with tyre cord. However, it can be applied, if desired, to similar cords for use in other rubber products, but it is limited to cords of linear density not exceeding 800 mg/m (tex). Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



RUBBER AND THERMOPLASTICS HOSES, NON-COLLAPSIBLE, FOR FIRE-FIGHTING SERVICE - PART 2: SEMI-RIGID HOSES (AND HOSE ASSEMBLIES) FOR PUMPS AND VEHICLES (FIRST REVISION) (ISO 4642-2:2009, IDT)
MS ISO 4642-2:2010
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies the requirements and test methods for semi-rigid reel hoses for use on fire-fighting vehicles and trailer pumps. The hoses are intended for use at a maximum working p ....Read more ressure of 1,5 MPa for normal pressure hoses (category I) and 4,0 MPa for high pressure hoses (category II). The hoses are further subdivided into types and classes. 
This Malaysian Standard applies to delivery hoses for fire-fighting purposes intended for use at a minimum ambient temperature of ?20 °C.

Hoses conforming to this Malaysian Standard should be used with fire hose couplings conforming to the relevant national standards couplings.

Requirements are also given for hose assemblies (see 6.12) where these are fitted by the hose manufacturer.

NOTE 1. Hoses for use at temperatures lower than ?20 °C can be supplied by agreement between the manufacturer and purchaser.

NOTE 2. All pressures are expressed in megapascals where 1 MPa = 10 bar. Close

RM 60.00

Document will be sent via email



 Add To Cart
RUBBER AND THERMOPLASTICS HOSES, NON-COLLAPSIBLE, FOR FIRE-FIGHTING SERVICE - PART 1: SEMI-RIGID HOSES FOR FIXED SYSTEMS (FIRST REVISION) (ISO 4642-1:2009, IDT)
MS ISO 4642-1:2010
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies the requirements and test methods for semi-rigid reel hoses for fire-fighting purposes for use with fixed systems. The hoses are intended for use at a maximum working ....Read more pressure of 1.2 MPa for hoses of 19 mm and 25 mm inside diameter and 0.7 MPa for hoses of 33 inside diameter. 
Hoses conforming to this part of ISO 4642 are intended for applications where long intervals can occur between the occasions of use, for example on fixed fire hose reels in buildings and other construction works.

This Malaysian Standard applies exclusively to hoses for fire-fighting purposes intended for use at ambient conditions in non-aggressive or non-corrosive atmospheres within the temperature range ?20 °C to +60 °C

NOTE 1. Hoses for use at temperatures lower than ?20 °C can be supplied at the request of the purchaser.

NOTE 2. All pressures are expressed in megapascals where 1 MPa = 10 bar. Close

RM 45.00

Document will be sent via email



 Add To Cart
Rubber hoses and hose assemblies for water suction and discharge - Specification (First revision) (ISO 4641:2010, IDT)
MS ISO 4641:2012
Status : Original
Format : PDF

This Malaysian Standard specifies the minimum requirements for textile-reinforced, smooth-bore rubber water-suction and discharge hoses and hose assemblies. 
Three types of hoses and hose assem ....Read more blies are specified according to their operating duty requirements, i.e. their ambient and water temperature ranges:
- ambient temperatures: -25 °C to 70 °C;
- water temperatures during operation: 0 °C to 70 °C. Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • ...
  • 588
  • 589
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.