• :  
BM ENG
  • Subscription
  • MS Catalogue
  • MS Pack
  • Purchase History
  • Cart
  • Hi
    !
    • My Profile
    • Portal
    • Log Out

Modal title

Widget settings form goes here

Search Malaysian Standard (MS)
 Advanced Search Search

Test methods for water in engine coolant concentrate by the Karl Fischer reagent method
MS 1575 : 2003 (CONFIRMED:2014)
Status : 1st Confirmation
Format : PDF

1.1 This Malaysian Standard covers the determination of the water present in new or
unused glycol-based coolant concentrates using a manual (Test method A) or an automatic
(Test method B) ....Read more coulometric titrator procedure.

1.2 Many carbonyl compounds react slowly with the Fischer reagent, causing a fading end point and leading to high results. A modified Fischer reagent procedure is included that minimises these undesirable and interfering reactions.

1.3 This standard does not purport to address all of the safety problems, if any,
associated with its use. It is the responsibility of the user of this standard to establish
appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. Close

RM 30.00

Document will be sent via email



 Add To Cart
Pencils - Specification (First revision)
MS 1159:2009 (CONFIRMED:2014)
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies requirements and test methods for wooden-cased black
lead pencils primarily intended for writing, drafting and drawing purposes.

RM 15.00

Document will be sent via email



 Add To Cart
Method of test for determination of total non-ionic detergent by batch technique
MS 1080:1987 (CONFIRMED:2014)
Status : Original
Format : PDF

This Malaysian Standard describes a method applicable to synthetic detergents for the determination of non-ionic detergent using the batch technique. Any other non-ionic material such as free fatty al ....Read more cohol, fatty amides and free oil will be included in this determination. Close

RM 15.00

Document will be sent via email



 Add To Cart
Specification for detergent powder for hand wash household laundry (First revision)
MS 553:2002 (CONFIRMED:2014)
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies the requirements and methods of analysis for detergent for
hand wash household laundry in powder form. It does not cover other special detergents like
soa ....Read more kers, low suds, etc. The formulation of this detergent may contain one or more builders
and/or other additives depending on the end use of the product. Close

RM 30.00

Document will be sent via email



 Add To Cart
Specification for magnesium sulphate, fertilizer grade (Second revision)
MS 54:2001 (CONFIRMED:2014)
Status : 2nd Revision
Format : PDF

This Malaysian Standard specifies the requirements for magnesium sulphate, fertilizer grade.

RM 15.00

Document will be sent via email



 Add To Cart
RUBBER TREAD COMPOUND FOR HOT (CONVENTIONAL) RETREADING OF PASSENGER CAR AND COMMERCIAL VEHICLE TYRES – SPECIFICATION (THIRD REVISION)
MS 1097:2020
Status : 3rd Revision
Format : PDF

This Malaysian Standard specifies the minimum requirements for rubber tread compound for
retreading of pneumatic tyres for use of passenger cars and commercial vehicles.
The rubber tread c ....Read more ompound specified in this standard covers those suitable for use in hot
(conventional) retreading (camelback, slab or stripwinding) process only Close

RM 15.00

Document will be sent via email



 Add To Cart
PRECURED TREAD FOR RETREADING TYRES – SPECIFICATION (THIRD REVISION)
MS 1208:2020
Status : 3rd Revision
Format : PDF

This Malaysian Standard specifies the minimum requirements for precured tread for retreading
tyres.

RM 15.00

Document will be sent via email



 Add To Cart
CUSHION GUM USED IN PRECURED RETREADING OF TYRES –SPECIFICATION (THIRD REVISION)
MS 1348:2020
Status : 3rd Revision
Format : PDF

This Malaysian Standard specifies the requirements for cushion gum (calendered sheet or orbi
strip) used in the precured process of retreading tyres.

RM 15.00

Document will be sent via email



 Add To Cart
Float glass - Specification (Second revision)
MS 1135:2020
Status : 2nd Revision
Format : PDF

This Malaysian Standard specifies the requirements for annealed, flat soda-lime glass
supplied as cut sizes or stock sheets.
This standard also covers the quality requirements of flat, tra ....Read more nsparent, clear and tinted glass.
This glass is intended to be used primarily for architectural glazing products including coated
glass, safety glass and insulating glass units.
NOTE. Reflective distortion is not addressed in this standard. Close

RM 30.00

Document will be sent via email



 Add To Cart
Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 2: Cracking-resistant carbon and low alloy steels, and the use of cast irons (First revision) (ISO 15156-2:2015, MOD)
MS 2285-2:2020
Status : 1st Revision
Format : PDF

This part of ISO 15156 gives requirements and recommendations for the selection and qualification
of carbon and low-alloy steels for service in equipment used in oil and natural gas production a ....Read more nd
natural gas treatment plants in H2S-containing environments, whose failure can pose a risk to the
health and safety of the public and personnel or to the environment. It can be applied to help to avoid
costly corrosion damage to the equipment itself. It supplements, but does not replace, the materials
requirements of the appropriate design codes, standards or regulations.
This part of ISO 15156 addresses the resistance of these steels to damage that can be caused by sulfide
stress-cracking (SSC) and the related phenomena of stress-oriented hydrogen-induced cracking
(SOHIC) and soft-zone cracking (SZC).
This part of ISO 15156 also addresses the resistance of these steels to hydrogen-induced cracking (HIC)
and its possible development into stepwise cracking (SWC).
This part of ISO 15156 is concerned only with cracking. Loss of material by general (mass loss) or
localized corrosion is not addressed.
Table 1 provides a non-exhaustive list of equipment to which this part of ISO 15156 is applicable,
including permitted exclusions.
This part of ISO 15156 applies to the qualification and selection of materials for equipment designed and
constructed using load controlled design methods. For design utilizing strain-based design methods,
see ISO 15156-1:2015, Clause 5.
Annex A lists SSC-resistant carbon and low alloy steels, and A.2.4 includes requirements for the use
of cast irons.
This part of ISO 15156 is not necessarily suitable for application to equipment used in refining or
downstream processes and equipment. Close

RM 75.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 572
  • 573
  • 574
  • 575
  • 576
  • 577
  • 578
  • 579
  • 580
  • 581
  • ›