• :  
BM ENG
  • Subscription
  • MS Catalogue
  • MS Pack
  • Purchase History
  • Cart
  • Hi
    !
    • My Profile
    • Portal
    • Log Out

Modal title

Widget settings form goes here

Search Malaysian Standard (MS)
 Advanced Search Search

PLASTICS - GUIDELINES FOR THE RECOVERY AND RECYCLING OF PLASTICS WASTE (ISO 15270:2008, IDT)
MS ISO 15270:2008
Status : Original
Format : PDF

This Malaysian Standard provides guidance for the development of standards and specifications covering plastics waste recovery, including recycling. The standard establishes the different options for ....Read more the recovery of plastics waste arising from pre-consumer and post-consumer sources as illustrated diagrammatically in Annex A. The standard also establishes the quality requirements that should be considered in all steps of the recovery process, and provides general recommendations for inclusion in material standards, test standards and product specifications. Consequently, the process stages, requirements, recommendations and terminology presented in this International Standard are intended to be of general applicability. Close

RM 30.00

Document will be sent via email



 Add To Cart
Ergonomics of the thermal environment - Risk assessment strategy for the prevention of stress or discomfort in thermal working conditions (ISO 15265:2004, IDT)
MS ISO 15265:2008 (CONFIRMED:2019)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard describes a strategy for assessing and interpreting the risk of physiological constraints, or of discomfort, while working in a given climatic environment.

It is ....Read more applicable in any working situation with steady or varying conditions of the climate, metabolic rate or clothing.

This Malaysian Standard does not describe a single procedure, but a strategy in three stages that can be used successively to gain deeper insight in the working conditions, as it is needed to draw the most appropriate conclusions about the risk involved and identify the best control and prevention measures.

It is definitely oriented towards the prevention and/or control of these working problems in the heat or cold. The risk of heat or cold disorders and/or discomfort is therefore assessed only to the extent that it is required to reach this goal.

However, users must comply with national legislations that may require that risk assessment be performed more systematically.

As the st Close

RM 30.00

Document will be sent via email



 Add To Cart
Medical devices - Quality management - Medical device nomenclature data structure (First Revision) (ISO 15225:2010, IDT)
MS ISO 15225:2011
Status : Withdrawn
Format : PDF

This Malaysian Standard provides rules and guidelines for a medical device nomenclature data structure, in order to facilitate cooperation and exchange of data used by regulatory bodies on an internat ....Read more ional level between interested parties, e.g. regulatory authorities, manufacturers, suppliers, health care providers and end users.

This standard includes guidelines for a minimum data set and its structure. These guidelines are provided for system designers setting up databases that utilize the nomenclature system described herein.

The requirements contained in this standard are applicable to the development and maintenance of an international nomenclature for medical device identification.

This standard does not include the nomenclature itself, which is provided as a data file. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



Clinical laboratory medicine - In vitro diagnostic medical devices - Validation of user quality control procedures by the manufacturer (ISO 15198:2004, IDT)
MS ISO 15198:2008 (CONFIRMED:2015)
Status : Withdrawn
Format : PDF

This Malaysian Standard describes a process for manufacturers of in vitro diagnostic medical devices to validate quality control procedures they recommend to their users. These quality control procedu ....Read more res are intended to provide users with assurance that device performance is consistent with its intended use and the manufacturers' claims. This standard applies to all in vitro diagnostic medical devices. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



Laboratory medicine - Requirements for reference measurement laboratories (ISO 15195:2003, IDT)
MS ISO 15195:2008 (CONFIRMED:2015)
Status : Withdrawn
Format : PDF

This Malaysian Standard gives the specific requirements for reference measurement laboratories in laboratory medicine. Examinations of properties with results reported on a nominal or ordinal scale ar ....Read more e not included.

This Malaysian Standard is not applicable to routine medical laboratories. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



In vitro diagnostic medical devices - Measurement of quantities in samples of biological origin - Requirements for certified reference materials and the content of supporting documentation (First revision) (ISO 15194:2009, IDT)
MS ISO 15194:2010 (CONFIRMED:2015)
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies requirements for certified reference materials and the content of their supporting documentation, in order for them to be considered of higher metrological. It is app ....Read more licable to certified reference materials classifiable as primary measurement standards, secondary measurement standards and international conventional calibrators that function either as calibrators or trueness control materials. This standard also provides requirements on how to collect data for value determination and how to present the assigned value and its measurement uncertainty.

This Malaysian Standard applies to certified reference materials with assigned values of differential or rational quantities. Annex A provides information on nominal properties and ordinal quantities.

This Malaysian Standard does not apply to reference materials that are parts of an in vitro diagnostic measuring system, although it is possible that many elements are helpful. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



In vitro diagnostic medical devices - Measurement of quantities in samples of biological origin - Requirements for content and presentation of reference measurement procedures (First revision) (ISO 15193:2009, IDT)
MS ISO 15193:2010 (CONFIRMED:2015)
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies requirements for the content of a reference measurement procedure for in vitro diagnostic medical devices and medical laboratories.

This Malaysian Stand ....Read more ard applies to reference measurement procedures providing values of differential or rational quantities. Annex A provides information on nominal properties and ordinal quantities.

This Malaysian Standard is valid for any person, body or institution involved in one of the various branches of laboratory medicine whose intention is to write a document to serve as a reference measurement procedure.

Full descriptions of measurement methods are usually published in scientific literature, in which methods are described in sufficient detail that they can be used as the basis of a documented measurement procedure. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



Medical laboratories - Requirements for safety (ISO 15190:2003, IDT)
MS ISO 15190:2008 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies requirements for safe practices in the medical laboratory.

RM 75.00

Document will be sent via email



 Add To Cart
Medical laboratories - Requirements for quality and competence (Second revision) (ISO 15189:2012, IDT)
MS ISO 15189:2014 (CONFIRMED:2020)
Status : 2nd Revision
Format : PDF

This Malaysian Standard specifies requirements for quality and competence particular to medical laboratories. It can be used by accreditation body in confirming the competence of medical laboratories ....Read more and by medical laboratories in designing their quality management system and assessing their own competence. Close

RM 90.00

Document will be sent via email



 Add To Cart
Ground granulated blast furnace slag for use in concrete, mortar and grout - Part 2: Conformity evaluation (First revision)
MS EN 15167-2:2010 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies the scheme for the evaluation of conformity of ground granulated blastfurnace slag according to EN 15167-1.

The standard provides technical rules for ....Read more the production control by the manufacturer, including autocontrol testing of samples. It also provides rules for actions to be followed in the event of non-conformity, the procedure for the certification of conformity and requirements for dispatching centres. Close

RM 45.00

Document will be sent via email

For sale within Malaysia Only

 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • ...
  • 580
  • 581
  • ›