• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




SPECIFICATION FOR PLASTICS CONTAINERS : PART 3 : CONTAINERS OVER 5 L UP TO AND INCLUDING 60 L
MS 1407: PART 3:2001
Status : Original
Format : PDF

This Malaysian Standard specifies tolerances on dimensions and performance requirements for free standing blow moulded containers with capacities over 5 L up to and including 60 L. Method of measureme ....Read more nt and methods of test for certain important properties of the containers are also specified. Close

RM 45.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR PLASTICS CONTAINERS : PART 4 : CLOSED HEAD PLASTICS DRUMS OVER 70 L UP TO AND INCLUDING 250 L TOTAL CAPACITY
MS 1407 : PART 4 : 2001
Status : Original
Format : PDF

This Malaysian Standard specifies the capacity, mass and tolerances on dimensions for blow moulded drums having capacity over 70 L up to and including 250 L.

RM 30.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR PLASTICS CONTAINERS PART 2 : CAPACITY, MASS AND TOLERANCES ON DIMENSIONS FOR PLASTIC CONTAINERS HAVING CAPACITY OF LESS THAN 5 L
MS 1407 : PART 2 : 1996
Status : Original
Format : PDF

This Part of the Malaysian Standard specifies tolerances on capacities, mass and dimensions for plastics container having capacity of less than 5 l.

RM 45.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR PLASTICS CONTAINERS PART 1 : SCREW THREAD FINISHES FOR PLASTICS CONTAINERS
MS 1407: PART 1:1996
Status : Original
Format : PDF

This Malaysian Standard specifies the thread configuration and dimensions for finishes for plastics containers with screw-type closures, having a maximum capacity of 250l and a maximum containers dime ....Read more nsion of 305 mm (12 in.). Included are tolerances for bottle capacity and body dimensions. Close

RM 45.00

Document will be sent via email



 Add To Cart
CODE OF PRACTICE FOR SYSTEM OF TOLERANCES FOR THE DIMENSION OF PLASTICS MOULDING
MS 1406:1996 (CONFIRMED:2009)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard recommends a system of tolerances for the dimensions of plastics mouldings produced from thermoplastics and thermosetting moulding materials by compression moulding, transfer m ....Read more oulding or injection moulding. The tolerances do not apply to extrusions, blown or foam mouldings, or deep drawn or sintered parts. Close

RM 30.00

Document will be sent via email



 Add To Cart
CODING SYSTEM FOR PLASTICS PRODUCTS (FIRST REVISION)
MS 1405:2008
Status : -1
Format : PDF

This Malaysian Standard provides a system for uniform marking of the plastics products, which have been fabricated (excluding additives, silk screening, metal-blading) from polymeric materials. 
....Read more >
The acronyms (abbreviations) used are to provide for generic identification of the polymer(s). Close

RM 15.00

Document will be sent via email



 Add To Cart
ELECTRICITY GENERATING SETS - PORTABLE (UP TO 5 kW)
MS 1403:1996 (CONFIRMED:2003)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies requirements for self-contained transportable electricity generating sets (hereinafter referred to as generating sets) driven by internal combustion engines and inten ....Read more ded to provide an independent 50 Hz a.c. supply, of low voltage, single-phase at 240V. They may be portable or transportable. 

The requirements apply to auxiliary power circuits of electric arc welding machines (see IEC 974) but not to their main welding circuits. 

This Standard does not apply to generating sets intended solely for charging batteries.For electrical safety requirements, this Standard shall be read in conjunction with IEC MS 335-1. 

NOTE 1. A generating set may include a separate extra-low voltage d.c. output, e.g. 12V, for battery-charging purposes. 

NOTE 2. The terms `extra-low voltage', `low voltage', are as defined in IEC MS 335-1. 

NOTE 3. Generating sets complying with this standard are not normally suitable for operation in parallel with other sets or with reticu Close

RM 60.00

Document will be sent via email



 Add To Cart
RUBBER HOSES, TEXTILE-REINFORCED, FOR GENERAL-PURPOSE WATER APPLICATIONS - SPECIFICATION (ISO 1403:2005, IDT)
MS ISO 1403:2007 (CONFIRMED:2023)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies the requirements for three types of general-purpose textile-reinforced rubber water hose with an operating temperature range of -25 °C to + 70 °C and a maximum work ....Read more ing pressure of up to 25 bar 1). 

These hoses are not intended to be used for conveyance of potable (drinking) water, for washing-machine inlets, as firefighting hoses, for special agricultural machines or as collapsible water hoses. 

These hoses may be used with additives which lower the freezing point of water. Close

RM 15.00

Document will be sent via email



 Add To Cart
CODE OF PRACTICE FOR SANITARY SYSTEM IN BUILDINGS - PART 2: INSTALLATION (FIRST REVISION)
MS 1402: PART 2:2006
Status : 1st Revision
Format : PDF

This Malaysian Standard gives recommendations on basic workmanship and covers those tasks, which are frequently carried out in relation to buildings, sanitary appliances installation. 

F ....Read more or design aspects sanitary appliances installation reference should be made to BS 5572 and AS 3500.2. 

NOTE. This Malaysian Standard includes supplementary elements in the form of commentaries to assist in its use and understanding. Compliance with the commentaries is not necessary in order to be able to claim conformity with this Malaysian Standard. Close

RM 30.00

Document will be sent via email



 Add To Cart
CODE OF PRACTICE FOR SANITARY SYSTEM IN BUILDINGS – PART 1: DESIGN (FIRST REVISION)
MS 1402: PART 1:2006
Status : 1st Revision
Format : PDF

This Malaysian Standard gives recommendation for planning, designing, installation and workmanship of sanitary systems in building, which includes water supply system, sanitary appliances, sanitary pi ....Read more pework, sanitary appurtenances and ventilation system including all other works necessary for non-pressure domestic, commercial and public buildings. This standard covers only from the fitting discharge to the final manhole. 

This standard is intended to indicate what is considered to be the minimum requirements for the design of sanitary system and good practice, under normal conditions. However, it also covers any special requirements of building such as may be found in hospitals, research and similar laboratories, or trade waste discharge. 

This standard's recommendations should be supplemented as required by skilled engineering advice based on knowledge of sanitary work practices and of local conditions. Close

RM 120.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 418
  • 419
  • 420
  • 421
  • 422
  • 423
  • 424
  • ...
  • 588
  • 589
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.