• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Steel library shelving - Specification (First revision)
MS 1430:2010 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies steel, cantilevered library shelving units for installation in the form of bays and covers principal dimensions, materials, finish and design concept.

RM 30.00

Document will be sent via email



 Add To Cart
RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS WITHOUT INTEGRAL OVERCURRENT PROTECTION FOR HOUSEHOLD AND SIMILAR USES (RCCB'S) PART 1 : GENERAL RULES
MS 1426:1997
Status : Original
Format : PDF

This Malaysian Standards applies to residual current operated circuit-breakers functionally independent of, or functionally dependent on, line voltage, for household and similar uses, not incorporatin ....Read more g over current protection (here after referred to as RCCB’s), for rated voltages not exceeding 440 V a.c. and rated currents not exceeding 125 A, in tended principally for protection against shock-hazard. Close

RM 165.00

Document will be sent via email



 Add To Cart
GLOSSARY OF TERMS FOR PACKAGING PART 3 : PLASTICS SACKS
MS 1425 : PART 3 : 1997 (CONFIRMED:2023)
Status : 1st Confirmation
Format : PDF

GLOSSARY OF TERMS FOR PACKAGING PART 3 : PLASTICS SACKS SECTION ONE. GENERAL

RM 30.00

Document will be sent via email



 Add To Cart
GLOSSARY OF TERMS FOR PACKAGING PART 2 : PLASTICS AND FLEXIBLE PACKAGING
MS 1425 : PART 2 : 1997 (CONFIRMED:2023)
Status : 1st Confirmation
Format : PDF

GLOSSARY OF TERMS FOR PACKAGING PART 2. PLASTICS AND FLEXIBLE PACKAGING

RM 15.00

Document will be sent via email



 Add To Cart
GLOSSARY OF TERMS FOR PACKAGING : PART 1 : GENERAL (INCLUDING AUXILIARY MATERIALS)
MS 1425 : PART 1 : 1997
Status : Original
Format : PDF

GLOSSARY OF TERMS FOR PACKAGING PART 1 : GENERAL (INCLUDING AUXILIARY MATERIALS)

RM 45.00

Document will be sent via email



 Add To Cart
TEST METHOD FOR PACKAGE YIELD OF PLASTICS FILM (FIRST REVISION)
MS 1424:2009
Status : Withdrawn
Format : PDF

1.1 This Malaysian Standard covers the determination of yield (area per unit mass) of plastic film. 

1.2 This Malaysian Standard also described in this test method is the means for cal ....Read more culating nominal yield, given values for nominal density, and nominal thickness. This is needed since, in material specifications, limits for yield are normally stated in terms of the percent deviation of actual yield from nominal yield. 

1.3 The values stated in SI units are to be regarded as the standard. The values given in brackets are for information only. 

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 

NOTE 1—This test method is not equivalent to ISO 4591. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



TEST METHOD FOR BLOCKING LOAD OF PLASTICS FILM BY THE PARALLEL PLATE METHOD (FIRST REVISION)
MS 1423:2009
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies a method for determining the quantitative information regarding the degree of blocking (unwanted adhesion) existing between layers of plastics film. It is not intende ....Read more d to measure susceptibility to blocking. 

1.2 By this procedure, the film-to-film adhesion is expressed as a blocking load in grams, which will cause two layers of polyethylene film to separate with an area of contact of 100 cm2 to separate. The test method is limited to a maximum load of 200 g. 

1.3 The values stated in SI units are to be regarded as standard. The values given in brackets are for information only. 

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 

NOTE 1—This test method is similar to ISO 11502 Method B, but is not technically equivale Close

RM 15.00

Document will be sent via email



 Add To Cart
TEST METHOD FOR UNRESTRAINED LINEAR THERMAL SHRINKAGE OF PLASTICS FILM AND SHEETING (FIRST REVISION)
MS 1422:2009
Status : 1st Revision
Format : PDF

This Malaysian Standard covers determination of the degree of unrestrained linear thermal shrinkage at given specimen temperatures of plastic film and sheeting of 0.76 mm [0.030 in.] thickness or less ....Read more . This test method does not cover shrinkage from loss of solvent in some materials. 

This Malaysian Standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 

NOTE 1—This document is not equivalent to ISO 11501. Close

RM 15.00

Document will be sent via email



 Add To Cart
Test method for haze and luminous transmittance of transparent plastics (Second revision)
MS 1421:2014
Status : Withdrawn
Format : PDF

This test method covers the evaluation of specific light transmitting and wide-angle-light-scattering properties of planar sections of materials such as essentially transparent plastic. Two procedures ....Read more are provided for the measurement of luminous transmittance and haze. Procedure A uses a hazemeter as described in Section 5 and Procedure B uses a spectrophotometer as described in Section 8. Material having a haze value greater than 30 % is considered diffusing and should be tested in accordance with Practice E2387. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



SPECIFICATION FOR ACRYLONITRILE BUTADIENE STYRENE (ABS) PIPES AND FITTINGS FOR PRESSURE APPLICATIONS PART 4 : GUIDES FOR INSTALLATION OF ABS PIPE SYSTEMS
MS 1419 : PART 4 : 1998 (CONFIRMED:2019)
Status : Original
Format : PDF

This Malaysian Standard specifies requirements and sets out recommended methods for installing acrylonitrile butadiene styrene (ABS) pipelines, above or below ground, for both pressure and non-pressur ....Read more e applications. Information is included on the selection, storage and handling, of ABS pipes. Close

RM 75.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 415
  • 416
  • 417
  • 418
  • 419
  • 420
  • 421
  • ...
  • 588
  • 589
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.