CYLINDERS FOR ACETYLENE - BASIC REQUIREMENTS - PART 2: CYLINDERS WITH FUSIBLE PLUGS (FIRST REVISION) (ISO 3807-2:2000, IDT)
MS ISO 3807-2:2007Status : 1st Revision
Format : PDF
This Malaysian standard specifies the basic requirements for acetylene cylinders with shells made from steel and equipped with fusible plugs with a maximum nominal water capacity of 150 L. It includes ....Read more
CYLINDERS FOR ACETYLENE - BASIC REQUIREMENTS - PART 1: CYLINDERS WITHOUT FUSIBLE PLUGS (FIRST REVISION) (ISO 3807-1:2000, IDT)
MS ISO 3807-1:2007Status : 1st Revision
Format : PDF
This Malaysian standard species the basic requirements for acetylene without fusible plugs or other safety devices with a maximum nominal water capacity of 150 L. It includes the procedures for type t ....Read more
Textiles - Woven fabrics - Determination of mass per unit length and mass per unit area (ISO 3801:1977 and AMD. 1:1977, IDT)
MS ISO 3801:2003 (CONFIRMED:2024)Status : 2nd Confirmation
Format : PDF
This Malaysian Standard specifies methods for the determination of
a) the mass per unit length, and
b) the mass per unit area,
of woven fabrics that have been conditioned in th
....Read more
Road vehicles - World manufacturer identifier (WMI) code (First revision) (ISO 3780:2009, IDT)
MS ISO 3780:2011 (CONFIRMED:2016)Status : 1st Confirmation
Format : PDF
This Malaysian Standard specifies the content and structure of an identifier in order to establish, on a worldwide basis, the identification of road vehicle manufacturers. The world manufacturer ident ....Read more
Road vehicles - Vehicle identification number (VIN) - Content and structure (First revision) (ISO 3779:2009, IDT)
MS ISO 3779:2011 (CONFIRMED:2016)Status : 1st Confirmation
Format : PDF
This Malaysian standard specifies the content and structure of a vehicle identification number (VIN) in order to establish, on a world-wide basis, a uniform identification system for road vehicles. ....Read more
HARDMETALS - ROCKWELL HARDNESS TEST (SCALE A) -PART 2 : PREPARATION AND CALIBRATION OF STANDARD TEST BLOCKS
MS ISO 3738-2 : 2001Status : Original
Format : PDF
This part of ISO 3738 specifies the preparation and calibration of hardmetal primary standard test blocks, secondary standard test blocks and working standard test blocks from master standard test blo ....Read more
WATER FOR ANALYTICAL LABORATORY USE - SPECIFICATION AND TEST METHODS (ISO 3696:1987, IDT)
MS ISO 3696:2007 (CONFIRMED:2025)Status : 2nd Confirmation
Format : PDF
This Malaysian Standard specifies the requirements and corresponding test methods for three grades of water for laboratory use for the analysis of inorganic chemicals.
It is not applic
....Read more
PAPER AND BOARD - DETERMINATION OF BURSTING STRENGTH AFTER IMMERSION IN WATER (ISO 3689:1983, IDT)
MS ISO 3689:2010 (CONFIRMED:2023)Status : 1st Confirmation
Format : PDF
This Malaysian Standard specifies a method for the determination of the wet strength of Paper and board by measuring its bursting strength after it has been immersed in water for a specified period . ....Read more
PULPS - PREPARATION OF LABORATORY SHEETS FOR THE MEASUREMENT OF DIFFUSE BLUE REFLECTANCE FACTOR (ISO BRIGHTNESS) (ISO 3688 : 1999, IDT)
MS ISO 3688:2002Status : Original
Format : PDF
This Malaysian Standard specifies two procedures for the preparation of laboratory sheets prior to measuring the diffuse blue reflectance factor (ISO brightness). One is the traditional procedure base ....Read more
DETERMINATION OF FLASH POINT - RAPID EQUILIBRIUM CLOSED CUP METHOD (ISO 3679:2004, IDT)
MS ISO 3679:2009Status : Original
Format : PDF
This Malaysian Standard specifies a method for the determination of the closed cup flash point of paints (including water-borne paints), varnishes, paint binders, adhesives, solvents, petroleum, and r ....Read more