• :  
BM ENG
  • Subscription
  • MS Catalogue
  • MS Pack
  • Purchase History
  • Cart
  • Hi
    !
    • My Profile
    • Portal
    • Log Out

Modal title

Widget settings form goes here

Search Malaysian Standard (MS)
 Advanced Search Search

CODE OF PRACTICE FOR STRUCTURAL USE OF TIMBER : PART 6 : WORKMANSHIP, INSPECTION AND MAINTENANCE (FIRST REVISION)
MS 544 : PART 6 :2001 (CONFIRMED:2020)
Status : 1st Confirmation
Format : PDF

This part gives recommendations for the preparation, fabrication, inspection, storage,
handling and maintenance of materials and components. The recommendations given in this part are necessary ....Read more conditions for applicability of the permissible stresses and loads given elsewhere in MS 544. Materials should be applied, used and fixed in such a way as to perform adequately the functions for which they are designed.
Workmanship in fabrication, preparation and installation of materials should conform in all respects to accepted good practice.

There should be adequate supervision throughout the preparation and construction of the structure to ensure that it conforms to the principles and practical considerations of the design. Members which are damaged, crushed or split beyond the limits permitted for similar defects in the grading should be rejected or repaired to the satisfaction of the designers and approving authority. For wood particleboard, cement bonded particleboard and high density fibreboard, in addition to the recommendations given in this part, all the recommendations of BS 5669 should be followed. The clauses in this part apply to all assemblies other than those of glued laminated members which are dealt with in MS 758, BS 4169 and MS 544 : Part 3. Close

RM 30.00

Document will be sent via email



 Add To Cart
CODE OF PRACTICE FOR STRUCTURAL USE OF TIMBER : PART 4 : TIMBER PANEL PRODUCTS : SECTION 4 : ORIENTED STRAND BOARD (OSB)
MS 544 : PART 4 : SECTION 4 : 2001 (CONFIRMED:2020)
Status : 1st Confirmation
Format : PDF

This Section gives recommendations for the use of Oriented Strand Board (OSB) in
construction. The panels in conformance to this Section are intended for use as floor and wall
sheathings ....Read more in light framing construction. However, uses are not limited to these applications.
Other possible uses may include temporary formworks for concrete and furniture frames.
The strength values listed in Tables 5, 6 and 7 in this Section relate to product strength
properties but they are not design values to be used directly in engineering calculations
without proper reduction factors. These reduction factors take into account the variability of
strength of manufactured panels and also load duration. Since the production of OSB in this
country is still new, the reduction factor that relates to the manufacturing variation cannot be
determined. However, laboratory scale experiment had been conducted to make the
derivation of the allowable spans for OSB panels possible. Therefore, for the purpose of floor
design, the allowable span values given herein should be used Close

RM 30.00

Document will be sent via email



 Add To Cart
CODE OF PRACTICE FOR STRUCTURAL USE OF TIMBER : PART 11 : RECOMMENDED SPAN TABLES AND THEIR CALCULATIONS : SECTION 3 : CEILING BINDERS
MS 544 : PART 11 :SECTION 3 : 2001 (CONFIRMED:2020)
Status : 1st Confirmation
Format : PDF

This Section of MS 544 : Part 11 recommends a calculation basis for the permissible clear span of ceiling binders used in traditional pitched roof construction, i.e. not including trussed roofs. The m ....Read more ethod of calculation is for single span ceiling binders formed from solid timber and supported at each end by external or internal walls. The space above the ceiling binders is assumed to be accessible, thus both uniform loads and a single concentrated load are considered. A typical example of roof construction is given in Figure 1. This Section of MS 544 : Part 11 is applicable to the species, strength groups and grades of timber given in MS 544 : Part 2 Close

RM 45.00

Document will be sent via email



 Add To Cart
CODE OF PRACTICE FOR STRUCTURAL USE OF TIMBER : PART 2 : PERMISSIBLE STRESS DESIGN OF SOLID TIMBER (FIRST REVISION)
MS 544: PART 2: 2001
Status : 1st Revision
Format : PDF

This Part gives recommendations for the structural use of the Malaysian hardwood and
softwood timber species in load bearing members. It includes recommendations on quality,
grade stresses ....Read more and modification factors applicable to these timber when used as simple
members, or as parts of built-up components, or as parts of structures incorporating other
materials. It does not, and it is not intended to deal comprehensively with all aspects of timber
construction. In particular it does not cover well tried and traditional methods of timber
construction which have been employed successfully over a long period of time. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



CODE OF PRACTICE FOR STRUCTURAL USE OF TIMBER: PART 12: LAMINATED VENEER LUMBER FOR STRUCTURAL APPLICATION
MS 544 : PART 12:2006 (CONFIRMED:2020)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard applies to Laminated Veneer Lumber (LVL) products engineered for use in structural applications in which the primary loading is in either the edgewise or endwise direction [(Fi ....Read more gures 1a) and 1b)] such as rafters, headers, beams, joists, studs and columns. Secondary gluing shall be permitted for edgewise bending application. Use of scaffold planks or secondary end-jointing is beyond the scope of this standard.

Structural Laminated Veneer Lumber (SLVL) to be used in this standard shall be manufactured in accordance with MS 544 and shall meet all requirements of the standard. Structural Laminated Veneer Lumber is a product intended for use in dry service condition, Service class I or II, where the moisture content is not more than 20 %. Close

RM 75.00

Document will be sent via email



 Add To Cart
CODE OF PRACTICE FOR STRUCTURAL USE OF TIMBER: PART 10: PRESERVATIVE TREATMENT OF STRUCTURAL TIMBER
MS 544 : PART 10 : 2003 (CONFIRMED:2024)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard gives recommendations for preservative treatment of timbers to be used for structural purposes in Malaysia to protect them from degradation by wood-destroying organisms. It doe ....Read more s not cover the remedial treatment of existing timber in old buildings. It does not deal with the protection of timber against fire, nor with preserving the appearance of timber against weathering or staining.

NOTE. All wood preservatives used in Malaysia have to be registered with Pesticides Board Malaysia under the Pesticides Act 1974 Close

RM 45.00

Document will be sent via email



 Add To Cart
CODE OF PRACTICE FOR STRUCTURAL USE OF TIMBER : PART 5 : TIMBER JOINTS
MS 544 : PART 5 : 2001
Status : Withdrawn
Format : PDF

This part applies to joints in solid timber fabricated with mechanical fasteners described by Malaysian Standard. These include joints fabricated with the following mechanical fasteners:

....Read more a) nails;
b) wood screws;
c) bolts;
d) coach screws;
e) split-ring connectors; and
f) shear-plate connectors.

NOTES:
1. Design rules for specialised and patented mechanical fasteners and for variants of conventional fasteners are not included in this code.
2. This Standard doe.s not specifically cover glued timber-to-timber or timber-to plywood connections as occurred in fabricated components such as stressed skin panels or plywood webbed beams. In such cases, joint design can be based on the timber components in the connection, provided that the joint is fabricated using a rigid, durable adhesive. Phenolic type adhesives meet these requirements. The design of fabricated components comprising glued connections is therefore based on the fact that with correct bonding practice and quality control, a joint is developed
in which the adhesive bond strength and durability will be superior to the components comprising the joint. Reference may be made to AS 1720.1: 1988, Appendix D2 for information on methods for assessing the deformation of joints. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



CODE OF PRACTICE FOR STRUCTURAL USE OF TIMBER : PART 4 : TIMBER PANEL PRODUCTS : SECTION 2 : MARINE PLYWOOD
MS 544 : PART 4 : SECTION 2 : 2001 (CONFIRMED:2024)
Status : 1st Confirmation
Format : PDF

This section gives recommendations for the use of sanded and unsanded Marine Plywood, in balanced construction, manufactured in accordance with The Standard Product Manual for the Production of Malays ....Read more ian Basic Structural Grade (MBSG) Rated Plywood, Timber Technology Bulletin, No: 1, August 1995 by Forest Research Institute Malaysia, (FRIM) with special restriction on the species that are allowed to be used in the lay-up. These plywoods are designated as MBSG-Marine.

This section applies only to plywoods that are to be used in severe wetting conditions (open deck, jetty, etc) in buildings or civil construction works but not meant for shipbuilding, where direct and prolong contact with sea and fresh water is involved. This section is suitable for parts of marine craft such as decking, cabins and other similar parts. Close

RM 30.00

Document will be sent via email



 Add To Cart
CODE OF PRACTICE FOR STRUCTURAL USE OF TIMBER : PART 11 : RECOMMENDED SPAN TABLES AND THEIR CALCULATIONS : SECTION 2 : CEILING JOISTS
MS 544 : PART 11 : SECTION 2 : 2001 (CONFIRMED:2020)
Status : 1st Confirmation
Format : PDF

This Section of MS 544 : Part 11 recommends a calculation basis for permissible clear span for ceiling joists with access at a maximum spacing of 610 mm centre-to-centre. It does not cater for the des ....Read more ign of the ties of trussed rafters, whether prefabricated or otherwise. The uniform and concentrated loads recommended in Uniform Building By-Law (UBBL) : 1984 are considered.

This Section of MS 544 : Part 11 is applicable to the species, strength groups and grades of timber given in MS 544 : Part 2 for both single and continuous span ceiling joists as shown in Figure 1. Close

RM 45.00

Document will be sent via email



 Add To Cart
CODE OF PRACTICE FOR STRUCTURAL USE OF TIMBER: PART 4 : TIMBER PANEL PRODUCTS: SECTION 1 : STRUCTURAL PLYWOOD
MS 544 : PART 4 : SECTION 1 : 2001 (CONFIRMED:2024)
Status : 1st Confirmation
Format : PDF

This section gives recommendations for the use of sanded and unsanded structural plywoods, in balanced construction, manufactured in accordance with The Standard Product Manual for the Production of M ....Read more alaysian Basic Structural Grade (MBSG) Rated Plywood, Timber Technology Bulletin, No.1, August 1995, Forest Research Institute Malaysia (FRIM). When plywoods are intended for structural use, only plywoods that are MBSG rated or equivalent to MBSG rated or better than MBSG rated shall be specified. Reference should also be made to the panel grade and the surface finish, i.e. Sanded or Unsanded. Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 502
  • 503
  • 504
  • 505
  • 506
  • 507
  • 508
  • ...
  • 580
  • 581
  • ›