• :  
BM ENG
  • Subscription
  • MS Catalogue
  • MS Pack
  • Purchase History
  • Cart
  • Hi
    !
    • My Profile
    • Portal
    • Log Out

Modal title

Widget settings form goes here

Search Malaysian Standard (MS)
 Advanced Search Search

RUBBERS AND LATICES – NOMENCLATURE (ISO 1629:1995, MOD)
MS ISO 1629:2004
Status : Withdrawn
Format : PDF

This Malaysian Standard establishes a system of symbols for the basic rubbers in both dry and latexforms, based on the chemical composition of the polymer chain.

The purpose of this Mala ....Read more ysian Standard is to standardize the terms used in industry, commerce and government, and it is not intended to conflict with, but rather to act as a supplement to, existing trade names and trade marks.

NOTE 1. In technical papers or presentations, the name of the rubber should be used if possible. The symbols should follow the chemical name for use in later references. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 2: Poly(vinyl chloride resins) (ISO 1628-2:1998, IDT)
MS ISO 1628-2:2004 (CONFIRMED:2012)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies conditions for the determination of the reduced viscosity (also known as viscosity number) and K-value of PVC resins. It is applicable to resins in powder form which ....Read more consist of homopolymers of the monomer vinyl chloride and copolymers, terpolymers, etc., of vinyl chloride with one or more other monomers, but where vinyl chloride is the main constituent. The resins may contain small amount of unpolymerised substances (e.g. emulsifying or suspending agents, catalyst residues, etc.) and other substances added during the course of the polymerisation. Close

RM 30.00

Document will be sent via email



 Add To Cart
PLASTICS - DETERMINATION OF VISCOSITY NUMBER AND LIMITING VISCOSITY NUMBER - PART 6: METHYL METHACRYLATE POLYMERS (ISO 1628-6:1990, IDT)
MS ISO 1628-6:2008
Status : Original
Format : PDF

This Malaysian Standards specifies the conditions to be used for the determination of the viscosity number of methyl methacrylate polymer moulding and extrusion materials in dilute solution.
....Read more r /> lt applies to methyl methacrylate (MMA) homopolymers and copolymers, and mixtures of the two with a minimum of 80 % (m/m) of MMA and up to 20 % (m/m) of other monomers, with and without additives, as defined in ISO 8257-1.

NOTE: The dilute-solution viscosity of polymers tan be also ex- pressed as a limiting viscosity number [?] Close

RM 15.00

Document will be sent via email



 Add To Cart
PLASTICS - DETERMINATION OF THE VISCOSITY OF POLYMERS IN DILUTE SOLUTION USING CAPILLARY VISCOMETERS - PART 5: THERMOPLASTIC POLYESTER (TP) HOMOPOLYMERS AND COPOLYMERS (ISO 1628-5:1998, IDT)
MS ISO 1628-5:2008
Status : Original
Format : PDF

This Malaysian Standard specifies a method for the determination of the viscosity number (also referred to as “reduced viscosity”) of dilute solutions of thermoplastic polyesters (TPs) in certain ....Read more specified solvents. The method is applicable to poly(ethylene terephthalate) (PET), poly(butylene terephthalate) (PBT), poly- (cyclohexylenedimethylene terephthalate) (PCT), and poly(ethylene naphthalate) (PEN), as well as to copolyesters and other polyesters, defined in ISO 7792-1, that are soluble in one of the specifiedsolvents under the specified conditions.

The viscosity number is determined by the general procedure specified in ISO 1628-1, observing theparticular conditions specified in this part of ISO 1628.

The determination of the viscosity number of a thermoplastic polyester provides a measure of the relative molecular mass of the polymer. Close

RM 30.00

Document will be sent via email



 Add To Cart
PLASTICS - DETERMINATION OF THE VISCOSITY OF POLYMERS IN DILUTE SOLUTION USING CAPILLARY VISCOMETERS - PART 4: POLYCARBONATE (PC) MOULDING AND EXTRUSION MATERIALS (ISO 1628-4:1999, IDT)
MS ISO 1628-4:2008
Status : Original
Format : PDF

This Malaysian Standard describes the conditions necessary for the determination of the viscosity number (also known as the reduced viscosity) and the relative viscosity of polycarbonates in dilute so ....Read more lution.

It can be used for pure polycarbonates and blends with other polymers, as well as mixtures of both, with or without fillers, as defined in ISO 7391-1. Close

RM 30.00

Document will be sent via email



 Add To Cart
PLASTICS - DETERMINATION OF THE VISCOSITY OF POLYMERS IN DILUTE SOLUTION USING CAPILLARY VISCOMETERS - PART 3: POLYETHYLENES AND POLYPROPYLENES (ISO 1628-3:2001, IDT)
MS ISO 1628-3:2008
Status : Original
Format : PDF

This Malaysian Standard defines particular conditions for determining the reduced viscosity (also known as viscosity number) and intrinsic viscosity of polyethylenes and polypropylenes at 135 °C in d ....Read more ilute solution. It is applicable to low, medium and high-density polyethylenes and to a wide range of polypropylenes, including pure isotactic, stereoblock and atactic polymers.

The viscosity of polymer solutions may be affected by additives present in the sample. The value of a reduced viscosity determined by this method may therefore be unreliable if the sample contains fillers or other additives.

NOTE: Reduced viscosity is also known as the Staudinger function (Jv) and intrinsic viscosity as the Staudinger index (Jg). Close

RM 30.00

Document will be sent via email



 Add To Cart
PLASTICS - VINYL CHLORIDE HOMOPOLYMER AND COPOLYMER RESINS - SIEVE ANALYSIS IN WATER (ISO 1624:2001, IDT)
MS ISO 1624:2007
Status : Original
Format : PDF

This Malaysian Standard specifies a method for the determination of the sieve retention of vinyl chloride homopolymer and copolymer resins. Control of this characteristic can help to ensure consistenc ....Read more y of supply and predictable processing behaviour. Close

RM 30.00

Document will be sent via email



 Add To Cart
BELT DRIVES - ENDLESS WIDE V-BELTS FOR INDUSTRIAL SPEED-CHANGERS AND GROOVE PROFILES FOR CORRESPONDING PULLEYS (ISO 1604:1989, IDT)
MS ISO 1604:2005 (CONFIRMED:2012)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies the principal dimensions of endless wide V-belts for industrial Speed-changers, and the groove profiles of corresponding fixed or variable diameter pulleys.
....Read more r /> lt does not apply to Speed-changer belts used either as Parts of farm-machines (in particular harvesters), which are standardized in ISO 3410, or for the propulsion of self-propelled vehicles (motor-cycles, scooters, cars). Close

RM 30.00

Document will be sent via email



 Add To Cart
Specification for fire resistant doorsets - Part 4: Requirements and method of determining the performance of mortice locksets
MS 1601-4:2009 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies tests and performance requirements for mortice locksets used on fire resistant doorsets in buildings.

RM 60.00

Document will be sent via email



 Add To Cart
Specification for fire resistant doorsets - Part 3: Code of practice for installation of fire resistant doorsets
MS 1601-3:2009 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies requirements for the installation of fire resistant doorsets used to protect openings in walls and partitions which are required to resist the passage of fire.
....Read more
This standard also applies to transom panels over doors, where the panels are contained within the doorframe and form part of the fire resistant doorsets. This standard covers the installation procedures for door frames, door leaves as well as hardwares. Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 379
  • 380
  • 381
  • 382
  • 383
  • 384
  • 385
  • ...
  • 580
  • 581
  • ›