• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




MEDICAL DEVICE SOFTWARE - SOFTWARE LIFE CYCLE PROCESSES (IEC 62304:2006, IDT)
MS IEC 62304:2009
Status : Withdrawal without replacement
Format : PDF

This Malaysian Standard defines the life cycle requirements for medical device software. The set of processes, activities, and tasks described in this standard establishes a common framework for medic ....Read more al device software life cycle processes. This Malaysian Standard applies to the development and maintenance of medical device software when software is itself a medical device or when software is an embedded or integral part of the final medical device. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



Household electrical appliances - Measurement of standby power (First revision) (IEC 62301:2011, IDT)
MS IEC 62301:2012 (CONFIRMED:2024)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies methods of measurement of electrical power consumption in standby mode(s) and other low power modes (off mode and network mode), as applicable. It is applicable to el ....Read more ectrical products with a rated input voltage or voltage range that lies wholly or partly in the range 100 V a.c. to 250 V a.c. for single phase products and 130 V a.c. to 480 V a.c. for other products. This standard does not specify safety requirements. It does not specify minimum performance requirements nor does it set maximum limits on power or energy consumption. Close

RM 75.00

Document will be sent via email



 Add To Cart
High-voltage switchgear and controlgear - Part 202: High-voltage/low- voltage prefabricated substation (IEC 62271-202:2006, IDT)
MS IEC 62271-202:2007 (CONFIRMED:2013)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies the service conditions, rated characteristics, general structural requirements and test methods of prefabricated substations, which are cable connected, to be operate ....Read more d from inside or outside for alternating current of primary rated voltages above 1 kV and up to and including 52 kV, and for a transformer or maximum power 1 600 kVA, for service frequencies up to and including 60 Hz for outdoor installation in locations with public accessibility. Prefabricated substations can be situated at ground level or partially or completely below ground level. Close

RM 120.00

Document will be sent via email



 Add To Cart
High-voltage switchgear and controlgear - Part 209: Cable connections for gas-insulated metal-enclosed switchgear for rated voltages above 52 kV - Fluid-filled and extruded insulation cables - Fluid-filled and dry-type cable-terminations (IEC 62271-209:2007, IDT)
MS IEC 62271-209:2008 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard covers the connection assembly of fluid-filled and extruded cables to gas insulated metal enclosed switchgear (GIS), in single- or three-phase arrangements where the cable-term ....Read more inations are fluid-filled or dry type and there is a separating insulating barrier between the cable insulation and the gas insulation of the switchgear. Close

RM 30.00

Document will be sent via email



 Add To Cart
High-voltage switchgear and controlgear - Part 105: Alternating current switch-fuse combinations for rated voltages above 1 kV up to and including 52 kV (First revision) (IEC 62271-105:2012, IDT)
MS IEC 62271-105:2017
Status : 1st Revision
Format : PDF

This Malaysian Standard applies to three-pole units for public and industrial distribution systems which are functional assemblies of switches including switch-disconnectors and current limiting fuse ....Read more s designed so as to be capable of:

- breaking, at the rated recovery voltage, any current up to and including the rated shortcircuit breaking current;
- making, at the rated voltage, circuits to which the rated shortcircuit
breaking current applies.

It does not apply to fuse-circuit-breakers, fuse-contactors, combinations for motor-circuits or to combinations incorporating single capacitor bank switches. Close

RM 90.00

Document will be sent via email



 Add To Cart
HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR – PART 105: ALTERNATING CURRENT SWITCH-FUSE COMBINATIONS (IEC 62271-105:2002, IDT)
MS IEC 62271-105:2006
Status : Withdrawal with replacement
Format : PDF

This Malaysian Standard applies to three-pole units for public and industrial distribution systems which are functional assemblies of switches including switch-disconnectors and current limiting fuses ....Read more designed so as to be capable of 

– breaking, at the rated recovery voltage, any current up to and including the rated shortcircuit breaking current,

– making, at the rated voltage, circuits to which the rated short-circuit breaking current
applies.

It does not apply to fuse-circuit-breakers, fuse-contactors, combinations for motor-circuits or to combinations incorporating single capacitor bank switches. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: COMMON SPECIFICATIONS (FIRST REVISION) (IEC 62271-1:2007, IDT)
MS IEC 62271-1:2009
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies a.c. switchgear and controlgear designed for indoor and outdoor installation and for operation at service frequencies up to and including 60 Hz on systems having volt ....Read more ages above 1 kV. This standard applies to all high-voltage switchgear and controlgear. Close

RM 195.00

Document will be sent via email



 Add To Cart
HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 203: GAS-INSULATED METAL-ENCLOSED SWITCHGEAR FOR RATED VOLTAGE ABOVE 52 KV (IEC 62271-203:2003, IDT)
MS IEC 62271-203:2007
Status : Withdrawal with replacement
Format : PDF

This Malaysian Standard standard specifies requirements for gas-insulated, metal-enclosed switchgear in which the insulation is obtained, at least partly, by an insulating gas other than air at atmosp ....Read more heric pressure, for alternating current of rated voltages above 52 kV, for indoor and outdoor installation, and for service frequencies up to and including 60 Hz. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR – PART 200: AC METAL-ENCLOSED SWITCHGEAR AND CONTROLGEAR FOR RATED VOLTAGES ABOVE 1 kV AND UP TO AND INCLUDING 52 kV (IEC 62271-200:2003, IDT)
MS IEC 62271-200:2005
Status : Withdrawal with replacement
Format : PDF

This Malaysian Standard specifies the requirments for factory-assembled metal-enclosed switchgear and controlgear for alternating current of rated voltages above 1 kV and up to and including 52 kV for ....Read more indoor and outdoor installation. It also applies for service frequencies up to and including 60 Hz. Enclosures may include fixed and removable components and may be filled with fluid (liquid or gas) to provide insulation. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 102: ALTERNATING CURRENT DISCONNECTORS AND EARTING SWITCHES (IEC 62271-102: 2001, IDT)
MS IEC 62271-102:2007
Status : Original
Format : PDF

This Malaysian Standard applies to alternating current disconnectors and earthing switches, designed for indoor and outdoor enclosed and open terminal installations for voltages above 1 000 V and for ....Read more service frequencies up to and including 60 Hz. Close

RM 135.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • ...
  • 588
  • 589
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.