• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Hand-held motor-operated electric tools - Safety-Part 2-3: Particular requirements for grinders, polishers and disk-type sanders (Second revision) (IEC 60745-2-3:2006, AMD. 1:2010, AMD. 2:2012, IDT)
MS IEC 60745-2-3:2019
Status : 2nd Revision
Format : PDF

This clause of Part 1 is applicable, except as follows:
Addition:
This standard applies to grinders, polishers and disk-type sanders, including angle, straight
and vertical tools, wi ....Read more th a rated capacity not exceeding 230 mm. For grinders, the rated speed
does not exceed a peripheral speed of the accessory of 80 m/s at rated capacity.
This standard does not apply to dedicated cut-off machines which are covered by
IEC 60745-2-22.
This standard does not apply to random-orbit polishers and random-orbit sanders which are
covered by IEC 60745-2-4.
This standard does not apply to die grinders utilizing collets or chucks for mounting threaded
cones and mandrel mounted wheels which are covered by IEC 60745-2-23. Close

RM 75.00

Document will be sent via email



 Add To Cart
Boxes and enclosures for electrical accessories for household and similar fixed electrical installations - Part 24: Particular requirements for enclosures for housing protective devices and other power dissipating electrical equipment (Second revision) (IEC 60670-24:2011, IDT)
MS IEC 60670-24:2019
Status : 2nd Revision
Format : PDF

This part of IEC 60670 applies to enclosures and parts of them for housing protective devices
and other power dissipating electrical equipment intended to be used with a rated voltage not
....Read more exceeding 400 V and a total incoming load current not exceeding 125 A for household and
similar fixed electrical installations.
These enclosures are intended to be installed where unskilled persons have access. They are
intended to be integrated with electrical equipment on site by skilled persons (installers).
They are intended to be installed where the prospective short circuit current does not exceed
10 kA unless they are protected by current limiting protective devices with a cut-off current not
exceeding 17 kA.
Enclosures complying with this standard are suitable for use, after installation, at ambient
temperature not normally exceeding 25 °C, but occasionally reaching 35 °C over 24 h, max.
40 °C and min. –5 °C.
An enclosure which is an integral part of an electrical accessory and provides protection
against external influences (e.g. mechanical impacts, ingress of solid objects or of water), is
covered by the relevant standard for such an accessory.
This standard does not apply to a low-voltage switchgear and controlgear assembly
(ASSEMBLY) as defined in the IEC 60439 or IEC 61439 series of standards nor to a main
entrance panel which may or may not be part of the distribution board.
NOTE 1 A main entrance panel is a set composed by a panel or an enclosure equipped with a meter and/or the
main incoming device. Main entrance panels comply with their appropriate standards or the requirements of the
local supplier if any.
NOTE 2 In the following country this standard cannot be used in installations with a 230 V single-phase supply
rated up to 100 A that is under the control of ordinary persons. Integration of mechanical and electrical devices into
an enclosure must be verified by compliance with IEC 60439-3 [British standard EN 60439-3]: UK.
NOTE 3 In the following country this standard can only be used for GP enclosures with the instructions according
to Annex A. For the other types of enclosures the integration of mechanical and electrical devices into an enclosure
is verified by compliance with DS EN 60439-3: DK. Close

RM 60.00

Document will be sent via email



 Add To Cart
Luminaires - Part 2-12: Particular requirements - Mains socket-outlet mounted nightlights (First revision) (IEC 60598-2-12:2013, IDT)
MS IEC 60598-2-12:2019 (CONFIRMED:2024)
Status : 1st Confirmation
Format : PDF

This part of IEC 60598 specifies requirements for mains socket-outlet mounted nightlights for use with electric light sources, on supply voltages not exceeding 250 V a.c. 50/60 Hz. It is to be read in ....Read more conjunction with those sections of Part 1 to which reference is made. Close

RM 15.00

Document will be sent via email



 Add To Cart
LUMINAIRES - PART 2-3: PARTICULAR REQUIREMENTS - LUMINAIRES FOR ROAD AND STREET LIGHTING (SECOND REVISION) (IEC 60598-2-3:2002, AMD. 1 :2011, IDT)
MS IEC 60598-2-3:2019
Status : 2nd Revision
Format : PDF

This part of IEC 60598 specifies requirements for
− luminaires for road, street lighting and other public outdoor lighting applications;
− tunnel lighting;
− column-integrated ....Read more luminaires with a minimum total height above normal ground level of
2,5 m;
and for use with electrical lighting sources on supply voltages not exceeding 1 000 V.
NOTE Column integrated luminaires with a total height below 2,5 m are under consideration. Close

RM 30.00

Document will be sent via email



 Add To Cart
Luminaires-Part 2-2: Particular requirements - Recessed luminaires (First revision) (IEC 60598-2-2:2011, IDT)
MS IEC 60598-2-2:2019
Status : 1st Revision
Format : PDF

This part of IEC 60598 specifies requirements for recessed luminaires incorporating electric
light sources for operation from supply voltages up to 1 000 V. This section does not apply to
....Read more air-handling or liquid-cooled luminaires. Close

RM 15.00

Document will be sent via email



 Add To Cart
Environmental testing - Part 2-2: Tests - Test B: Dry heat (First revision) (IEC 60068-2-2:2007, IDT)
MS IEC 60068-2-2:2019
Status : 1st Revision
Format : PDF

This standard deals with dry heat tests applicable both to heat-dissipating and non heatdissipating
specimens. For non heat-dissipating specimens, Tests Bb and Bd do not deviate
essentiall ....Read more y from earlier issues.
The object of the dry heat test is limited to the determination of the ability of components,
equipment or other articles to be used, transported or stored at high temperature.
These dry heat tests do not enable the ability of specimens to withstand or operate during the
temperature variations to be assessed. In this case, it would be necessary to use IEC 60068-
2-14 Test N: Change of temperature.
The dry heat tests are subdivided as follows:
Dry heat test for non heat-dissipating specimens
– with gradual change of temperature, Bb.
Dry heat tests for heat-dissipating specimens
– with gradual change of temperature, Bd;
– with gradual change of temperature, specimen powered throughout, Be.
The procedures given in this standard are normally intended for specimens that achieve
temperature stability during the performance of the test procedure. Close

RM 30.00

Document will be sent via email



 Add To Cart
Good Agricultural Practice (GAP) - Part 3: Rubber (Hevea brasiliensis (Willd. ex A.Juss.) Müll.Arg.) (First revision)
MS 1784-3:2019
Status : 1st Revision
Format : PDF

This Malaysian Standard defines the essential elements for sustainable rubber cultivation that
is legally compliant, environmentally sound, socially acceptable and economically viable to
e ....Read more nsure quality produce that is safe and suitable for utilisation.
This standard is applicable to the cultivation area not less than 40.47 hectares (100 acres) in a
piece of land or continuous planted area. Close

RM 30.00

Document will be sent via email



 Add To Cart
Determination of additive elements in lubricating oils by inductively coupled plasma atomic emission spectrometry - Test method (First revision)
MS 2036:2018
Status : 1st Revision
Format : PDF

1.1 This test method covers the quantitative determination
of barium, boron, calcium, copper, magnesium, molybdenum,
phosphorus, sulfur, and zinc in unused lubricating oils and
addit ....Read more ive packages.
1.2 The precision statements are valid for dilutions in which
the mass % sample in solvent is held constant in the range of
1 to 5 mass % oil.
1.3 The precision tables define the concentration ranges
covered in the interlaboratory study. However, both lower and
higher concentrations can be determined by this test method.
The low concentration limits are dependent on the sensitivity
of the ICP instrument and the dilution factor. The high
concentration limits are determined by the product of the
maximum concentration defined by the linear calibration curve
and the sample dilution factor.
1.4 Sulfur can be determined if the instrument can operate at
a wavelength of 180 nm.
1.5 The values stated in SI units are to be regarded as
standard. No other units of measurement are included in this
standard.
1.6 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appropriate
safety and health practices and determine the applicability
of regulatory limitations prior to use. Close

RM 15.00

Document will be sent via email



 Add To Cart
Evaluation of automotive engine oils in the sequence VIII spark-ignition engine (CLR oil test engine) - Test method (First revision)
MS 2035:2018
Status : -1
Format : PDF

engine oils (SAE grades 0W, 5W, 10W, 20, 30, 40, and 50, and
multi-viscosity grades) intended for use in spark-ignition
gasoline engines. The test procedure is conducted using a
carb ....Read more ureted, spark-ignition Cooperative Lubrication Research
(CLR) Oil Test Engine (also referred to as the Sequence VIII
test engine in this test method) run on unleaded fuel. An oil is
evaluated for its ability to protect the engine and the oil from
deterioration under high-temperature and severe service conditions.
The test method can also be used to evaluate the
viscosity stability of multi-viscosity-graded oils. Companion
test methods used to evaluate engine oil performance for
specification requirements are discussed in the latest revision
of Specification D4485.
1.2 Correlation of test results with those obtained in automotive
service has not been established. Furthermore, the
results obtained in this test are not necessarily indicative of
results that will be obtained in a full-scale automotive sparkignition
or compression-ignition engine, or in an engine
operated under conditions different from those of the test. The
test can be used to compare one oil with another.
1.3 The values stated in SI units are to be regarded as
standard. No other units of measurement are included in this
standard.
1.3.1 Exceptions—The values stated in inch-pounds for
certain tube measurements, screw thread specifications, and
sole source supply equipment are to be regarded as standard.
1.3.1.1 The bearing wear in the text is measured in grams
and described as weight loss, a non-SI term.
1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appropriate
safety and health practices and determine the applicability
of regulatory limitations prior to use. Specific precautionary
statements are provided throughout this test method. Close

RM 75.00

Document will be sent via email



 Add To Cart
Measuring the effect on filterability of engine oils after treatment with various amounts of water and a long (6 h) heating time - Test method (First revision)
MS 2034:2018
Status : 1st Revision
Format : PDF

tendency
of an oil to form a precipitate that can plug an oil filter.
It simulates a problem that may be encountered in a new engine
run for a short period of time, followed by a lon ....Read more g period of
storage with some water in the oil.
1.2 The values stated in SI units are to be regarded as
standard. No other units of measurement are included in this
standard.
1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appropriate
safety and health practices and determine the applicability
of regulatory limitations prior to use. Close

RM 15.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • ...
  • 587
  • 588
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.