• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Tests for mechanical and physical properties of aggregates - Part 2: Methods for the determination of resistance to fragmentation (Second revision)
MS EN 1097-2:2011 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

Tests for mechanical and physical properties
of aggregates - Part 2: Methods for the
determination of resistance to fragmentation
(Second revision)

RM 60.00

Document will be sent via email

For sale within Malaysia Only

 Add To Cart
Road vehicles - the use of compressed natural gas fuel for vehicle engines - code of practice (Second revision)
MS 1096:2011 (CONFIRMED:2020)
Status : 2nd Revision
Format : PDF

This Malaysian Standard specifies requirements for compressed natural gas (CNG) fuel
systems for engines mounted on motor vehicles, either for the propulsion of the vehicles or for
driving ....Read more some auxiliary function, e.g. a mixer or a pump. It provides requirements for the
design and construction of component parts, and for their installation in vehicles, and for
tests, commissioning, and periodic inspection. It applies to all vehicle types, e.g. rigid chassis,
articulated chassis and semitrailers.
This standard does not apply to forklifts, floor sweepers, polishers, tow tractors, elevating
work platforms and industrial stationary engines and to other CNG usage, such as the gas
supply system for appliances in caravans, mobile homes or for the propulsion of marine craft.
This standard does not cover the areas where major structural modifications are to be carried
out to the vehicle. Prior to commencement of such work guidance should be sought from the
vehicle manufacturer or a professional engineer who is experienced in the automotive
disciplines. Close

RM 90.00

Document will be sent via email



 Add To Cart
ROAD VEHICLES - THE USE OF COMPRESSED NATURAL GAS FUEL FOR VEHICLE ENGINES - CODE OF PRACTICE (SECOND REVISION)
MS 1096:2011, AMD. 1:2011
Status : Amendment 1
Format : PDF

This Malaysian Standard specifies requirements for compressed natural gas (CNG) fuel systems for engines mounted on motor vehicles, either for the propulsion of the vehicles or for driving some auxili ....Read more ary function, e.g. a mixer or a pump. It provides requirements for the design and construction of component parts, and for their installation in vehicles, and for tests, commissioning, and periodic inspection. It applies to all vehicle types, e.g. rigid chassis, articulated chassis and semitrailers. Close

FREE

Document will be sent via email



Please Login to enable MS to be send via email
METHODS OF TEST FOR CERAMIC TILES PART 4 : DETERMINATION OF SCRATCH HARDNESS OF SURFACE ACCORDING TO MOHS
MS 1091 : PART 4 : 1987
Status : Withdrawn
Format : PDF

This Malaysian Standard defines a method of test for determining the scratch hardness of the
surface of all ceramic tiles.

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



POLYETHYLENE (PE) PIPING SYSTEMS FOR GASEOUS FUELS SUPPLY - PART 4: VALVES
MS 1086: PART 4:2008
Status : Original
Format : PDF

This Malaysian Standard specifies the characteristics of valves made form polyethylene (PE)
for piping systems in the field of the supply of gaseous fuels.
NOTE. Valves made form other mat ....Read more erial than polyethylene designed for the supply of gaseous fuels conforming to
the relevant standards are permitted to be used in PE piping system according to MS 1086 provided they have
relevant PE connection for butt fusion or electrofusion ends (see MS 1086: Part 3).
It also specifies the test parameters for the test methods referred to in this standard.
In conjunction with the other parts of MS 1086 (see Foreword), it is applicable to PE valves,
their joints and to joints with components of PE and other materials intended to be used under
the following conditions:
a) a maximum operating pressure, MOP, up to and including 4 bar1) (PE 80) and 5 bar
(PE 100);
b) an operating temperature of 20 °C as reference temperature; and
c) an operating temperature between -20 °C and +40 °C.
MS 1086 covers a range of maximum operating pressures and gives requirements
concerning colours and additives.
NOTES:
1. For other operating temperatures, derating coefficients should be used, see MS 1086: Part 5.
2. It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects. taking
into account their particular requirements and any relevant national regulations and installation practices or codes.
It is applicable to bi-directional valves with spigot end or electrofusion socket intended to be
fused with PE pipes conforming MS 1086: Part 3 without any fittings or with PE fittings
conforming to MS 1086: Part 2.
This part of MS 1086 covers valves with a nominal size DN/OD < 225. Close

RM 30.00

Document will be sent via email



 Add To Cart
POLYETHYLENE (PE) PIPING SYSTEMS FOR GASEOUS FUELS SUPPLY - PART 3: FITTINGS
MS 1086: PART 3:2008
Status : Original
Format : PDF

This Malaysian Standard specifies the characteristics of fusion fittings made from
polyethylene (PE) as well as of mechanical fittings made from PE and other materials for
piping systems i ....Read more n the field of the supply of gaseous fuels.
It also specifies the test parameters for the test methods referred to in this standard.
In conjunction with the other parts of MS 1086 (see Foreword), it is applicable to PE fittings,
their joints and to joints with components of PE and other materials intended to be used under
the following conditions:
a) a maximum operating pressure, MOP, up to and including 4 bar1) (PE 80) and 5 bar
(PE 100); and
b) an operating temperature of 20 °C as reference temperature.
NOTE. For other operating temperatures, derating coefficients should be used, see MS 1086: Part 5.
MS 1086 covers a range of maximum operating pressures and gives requirements
concerning colours and additives.
NOTE. It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects,
taking into account their particular requirements and any relevant national regulations and installation practices or
codes.
This standard is applicable for fittings of the following types:
a) electrofusion socket fittings;
b) electrofusion saddle fittings; and
c) spigot end fittings.
The fittings can be in the form of couplers, equal and reduced tees, reducers, bends or caps,
etc. Close

RM 45.00

Document will be sent via email



 Add To Cart
POLYETHYLENE (PE) PIPING SYSTEMS FOR GASEOUS FUELS SUPPLY – PART 2: PIPES (FIRST REVISION)
MS 1086: PART 2:2007
Status : 1st Revision
Format : PDF

This part of MS 1086 specifies the characteristics of pipes made from polyethylene (PE) for
piping systems in the field of the supply of gaseous fuels.
It also specifies the test parameter ....Read more s for the test methods referred to in this standard.
In conjunction with the other parts of MS 1086 (see Foreword) it is applicable to PE pipes,
their joints and to joints with components of PE and other materials intended to be used under
the following conditions:
a) a maximum operating pressure, MOP, up to and including 4 bar1) (PE 80) and 5 bar (PE
100); and
b) an operating temperature of 20 °C as a reference temperature.
NOTE. For other operating temperatures, derating coefficients should be used, see MS 1086: Part 1.
MS 1086 covers a range of maximum operating pressures and gives requirements
concerning colours and additives.
NOTE. It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects,
taking into account their particular requirements and any relevant national guidance or regulations and installation
practices or codes. Close

RM 30.00

Document will be sent via email



 Add To Cart
POLYETHYLENE (PE) PIPING SYSTEMS FOR GASEOUS SUPPLY - PART 6: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
MS 1086: PART 6:2008
Status : Original
Format : PDF

This Malaysian Standard gives guidance for assessment of conformity for PE piping systems for gaseous supply to be included in the manufacturer's quality plan as part of the quality system.

....Read more /> This standard includes:

a) requirements for materials, components and joints given in the applicable Parts 1 to 5 of MS 1086;

b) requirements for the manufacturer's quality system; and

NOTE. It is recommended that the quality system conforms to MS ISO 9001[2].

c) definitions and procedures to be applied if third party certification is involved.

NOTE. If third party certification is involved, it is recommended that the certification body is accredited to MS ISO/IEC guide 65 [2], or MS ISO/IEC guide 65 [3] as applicable.

In conjunction with the other parts of this standard (see Foreword) it is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following condition:

a) a maximum operating pressure, MOP, up to Close

RM 30.00

Document will be sent via email



 Add To Cart
POLYETHYLENE (PE) PIPING SYSTEMS FOR GASEOUS SUPPLY - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM
MS 1086: PART 5:2008
Status : Original
Format : PDF

This Malaysian Standard specifies requirements of fitness for purpose of the polyethylene
(PE) piping system in the field of the supply of gaseous fuels.
It specifies the definitions of el ....Read more ectrofusion and also specifies the method of preparation of test
piece joints, relating to installation recommendations given in EN 12007-2[1] and the tests to
be carried out on these joints for assessing the fitness for purpose of the system under
normal and extreme conditions.
It also specifies the test parameters for the test methods referred to in this standard.
In conjunction with the other parts of this standard (see Foreword) it is applicable to PE pipes,
fittings, valves, their joints and to joints with components of other materials intended to be
used under the following conditions:
a) a maximum operating pressure, MOP, up to and including 4 bar1) (PE 80) and 5 bar (PE
100); and
b) an operating temperature of 20 °C as reference temperature. Close

RM 15.00

Document will be sent via email



 Add To Cart
POLYETHYLENE (PE) PIPING SYSTEMS FOR GASEOUS FUELS SUPPLY – PART 1: GENERAL (FIRST REVISION)
MS 1086: PART 1:2007
Status : 1st Revision
Format : PDF

This part of MS 1086 specifies the general aspects of polyethylene (PE) piping systems in the
field of the supply of gaseous fuels.
It also specifies the test parameters for the test metho ....Read more ds referred to in this standard.
In conjunction with the other parts of MS 1086 (see Foreword) it is applicable to PE pipes,
fittings, and valves, their joints and to joints with components of other materials intended to be
used under the following conditions:
a) a maximum operating pressure, MOP, up to and including 4 bar1) (PE 80) and 5 bar (PE
100); and
b) an operating temperature of 20 °C as reference temperature.
NOTE. For other operating temperatures, derating coefficients should be used, see MS 1086: Part 5.
MS 1086 covers a range of maximum operating pressures and gives requirements
concerning colours and additives.
NOTE. It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects,
taking into account their particular requirements and any relevant national regulations and installation practices or
codes. Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 454
  • 455
  • 456
  • 457
  • 458
  • 459
  • 460
  • ...
  • 588
  • 589
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.