• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




FAT AND OIL DERIVATIVES - FATTY ACID METHYL ESTER (FAME) - DETERMINATION OF CA, K, MG AND NA CONTENT BY OPTICAL EMISSION SPECTRAL ANALYSIS WITH INDUCTIVELY COUPLED PLASMA (ICP OES)
MS 2357:2010
Status : Original
Format : PDF

This Malaysian Standard specifies a procedure for the direct determination of the soap building elements Calcium (Ca), Magnesium (Mg), Sodium (Na) and Potassium (K) in fatty acid methyl esters (FAME) ....Read more by ICP OES at levels of about 1 mg/kg to 10 mg/kg.  Close

RM 15.00

Document will be sent via email



 Add To Cart
TEST METHOD FOR CLOUD POINT OF PETROLEUM PRODUCTS
MS 2356:2010
Status : Original
Format : PDF

This Malaysian Standard covers petroleum products and biodiesel fuels that are transparent in layers 40 mm in thickness, and with a cloud point below 49°C. NOTE1—The interlaboratory program consis ....Read more ted of petroleum products of Test Method D1500 color of 3.5 and lower.The precisions stated in this test method may not apply to samples with ASTM color higher than 3.5. The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.  Close

RM 15.00

Document will be sent via email



 Add To Cart
CORROSION-RESISTANT HIGH-SILICON IRON CASTINGS - SPECIFICATION
MS 2354:2010
Status : Original
Format : PDF

This Malaysian Standard covers high-silicon cast iron castings intended for corrosion resistant service. Selection of grade depends on the corrosive service to be experienced by the casting. All three ....Read more grades are suited for application in severe corrosive environments. However, Grade 2 is particularly suited for application in strong chloride environments, and Grade 3 is recommended for impressed current anodes.  Close

RM 30.00

Document will be sent via email



 Add To Cart
THERMAL INSULATING PRODUCTS - EVALUATION OF CONFORMITY
MS 2353:2010
Status : Original
Format : PDF

This Malaysian Standard specifies the procedures and the criteria for the evaluation of the conformity of a thermal insulating product with the relevant Malaysian product specification.

RM 45.00

Document will be sent via email



 Add To Cart
THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF BEHAVIOUR UNDER POINT LOAD
MS 2352:2010
Status : Original
Format : PDF

This Malaysian Standard specifies the equipment and procedures for determining the behaviour of products under a force applied to small area of a test specimen at a given speed. It is applicable to th ....Read more ermal insulating products. The standard can be used to determine whether the products have sufficient strength to withstand forces applied directly to them, either during installation or during application, mainly caused by pedestrian traffic. NOTE The test methods given in the main body of the standard and in annex A are reported and interpreted in different ways. The similarities that exist between the methods are not sufficient to permit reasonable comparisons to be made. Close

RM 15.00

Document will be sent via email



 Add To Cart
THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF SHEAR BEHAVIOUR
MS 2351:2010
Status : Original
Format : PDF

This Malalysian Standard specifies the equipment and procedures for determining shear behaviour. It is applicable to thermal insulating products. NOTE, The tests described in this standard do not det ....Read more ermine pure shear behaviour, but measure the effects of applying two opposite parallel forces to the major faces of the test specimen. The test is, however, called 'sheaf in this text by convention. The application of a force tangentially to the major surface of the test specimen is considered to represent more closely the stresses imposed upon thermal insulation products in many building applications, particularly walls, than other methods of measuring shear performance, e.g. bending tests. Close

RM 15.00

Document will be sent via email



 Add To Cart
THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF LONG TERM WATER ABSORPTION BY IMMERSION
MS 2350:2010
Status : Original
Format : PDF

This Malaysian Standard specifies the equipment and procedures for determining the long term water absorption of test specimens. It is applicable to thermal insulating products. This Malaysian Standa ....Read more rd specifies two options: Method 1- partial immersion Method 2 - total immersion The long term water absorption by partial immersion is intended to simulate the water absorption caused by long term water exposure. The long term water absorption by total immersion is not directly related to the conditions on site, but has been recognized as a relevant condition of test for some products in some applications. Close

RM 30.00

Document will be sent via email



 Add To Cart
THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF BENDING BEHAVIOUR
MS 2349:2010
Status : Original
Format : PDF

This Malaysian Standard specifies the equipment and procedures for determining the bending behaviour of full size products (method A) and test specimens (method B) under the action of three-point load ....Read more ing. It is applicable to thermal insulating products.The test is designed to determine the bending strength of products and their deflection at a given load. The method can be used to determine the resistance of the product to bending stresses during transport and application. Close

RM 15.00

Document will be sent via email



 Add To Cart
THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF WATER VAPOUR TRANSMISSION PROPERTIES
MS 2348:2010
Status : Original
Format : PDF

This Malaysian Standard specifies the equipment and procedures for determining the water vapour transmission rate, water vapour permeance and water vapour permeability of test specimens in the steady ....Read more state under different sets of specified test conditions. It is applicable to thermal insulating products. It is intended to be used for homogeneous materials (see note 1) and for products which may contain integral skins or facings of different material(s). NOTE I A material is considered to be homogeneous, with regard to mass distribution, if its density is approximately the same throughout, i.e. if the measured density values are close to its mean density. NOTE 2 This test method is not normally used for determining the water vapour transmission properties of single, separate vapour harriers (of high diffusion resistance ), such as prefabricated films, foils, membranes or sheets, due to the long duration of the test. For products with a vapour retarder or barrier with a water vapour diff Close

RM 30.00

Document will be sent via email



 Add To Cart
THERMAL INSULATING PRODUCTS FOR BUILDING APPLICATIONS - DETERMINATION OF SHORT TERM WATER ABSORPTION BY PARTIAL IMMERSION
MS 2347:2010
Status : Original
Format : PDF

This Malaysian Standard specifies the equipment and procedures for determining the short-term water absorption of specimens by partial immersion. It is applicable to thermal insulating products. NOTE ....Read more It is intended to simulate the water absorption caused by a 24 h raining period during construction work. Close

RM 15.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • ...
  • 587
  • 588
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.