• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Wheelchairs - Part 1: Guidelines for the application of the MS ISO 7176 series on wheelchairs
MS 2368-1:2010 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard explains how you can use the standards on wheelchairs to select your next wheelchair. The actual standards are very technical and, at first glance, you may not understand how t ....Read more his information will help you select a wheelchair or scooter. This standard is meant to help you understand the purpose for and content of the Malaysian Standards on wheelchairs. Close

RM 135.00

Document will be sent via email



 Add To Cart
Performance evaluation of in vitro diagnostic medical devices
MS 2367:2010 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard applies to the performance evaluation of in vitro diagnostic medical devices (IVD MDs) including IVD MDs for self-testing. It specifies the responsibilities and general require ....Read more ments for the planning, conduct, assessment and documentation of a performance evaluation study by the manufacturer. It does not apply to specific evaluation plans for certain IVD MDs or a specific use. Close

RM 30.00

Document will be sent via email



 Add To Cart
GUIDANCE ON THE APPLICATION OF MS IEC 60364-7-710 FOR GROUP 2: MEDICAL LOCATIONS
MS 2366:2010
Status : Original
Format : PDF

This Malaysian Standard applies to electrical installations in group 2 medical locations so as to ensure safety of patients and medical staff. It may be necessary to modify the existing electrical in ....Read more stallation, in accordance with this document, when a change of utilization of the location occurs. The requirements of this document do not apply to medical electrical equipment. For the latter reference should be made to the IEC 60601 series. This Malaysian Standard has to be used in conjunction with MS IEC 60364-7-710.  Close

RM 30.00

Document will be sent via email



 Add To Cart
Sterilisation of health care products - Moist heat - Part 2: Guidance on the application of MS ISO 17665-1
MS 2364-2:2010 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard provides general guidance on the development, validation and routine control of moist heat sterilization processes and is intended to explain the requirements set forth in MS I ....Read more SO 17665-1. Close

RM 90.00

Document will be sent via email



 Add To Cart
WORK IN TUNNELLING - CODE OF PRACTICE
MS 2363:2010
Status : Original
Format : PDF

This Malaysian Standard specifies code of practice for safety and health in tunnelling. It includes safety and health in the construction, maintenance and renovation of tunnelling. The standard inclu ....Read more des safety and health that are also relevant to cut-and-cover tunnelling and immersed tube tunnels. The standard is not specifically intended to apply to the construction of shafts or tunnels for the purpose of winning minerals. NOTE. A list of regulatory agencies related to tunnel construction is given in Annex A. Close

RM 270.00

Document will be sent via email



 Add To Cart
RECOVERED PAPER - GRADE DESCRIPTION AND MOISTURE INSPECTION PROCEDURES
MS 2362:2010 (CONFIRMED:2023)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard prescribes the requirements of recovered paper grades for the quality control that is suitable for domestic paper mills and the inspection procedures for moisture content.

RM 15.00

Document will be sent via email



 Add To Cart
Recovered waste oil - Specification
MS 2361:2010 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies the requirements and test methods for determining and classifying recovered waste oil. It is applicable to petroleum-based and synthetic waste oil.

RM 15.00

Document will be sent via email



 Add To Cart
TEST METHOD FOR RATE OF BURNING AND/OR EXTENT AND TIME OF BURNING OF PLASTICS IN A HORIZONTAL POSITION (FIRST REVISION)
MS 2360:2010
Status : 1st Revision
Format : PDF

This Malaysian Standard fire-test-response test method covers a small-scale laboratory screening procedure for comparing the relative linear rate of burning or extent and time of burning, or both, of ....Read more plastics in the form of bars, molded or cut from sheets, plates, or panels, and tested in the horizontal position. NOTE 1—This test method, and test method A of IEC 60695-11-10 are technically equivalent. NOTE 2—For additional information on materials which do not burn to the first reference mark by this test, see Test Method D 3801. This test method was developed for polymeric materials used for parts in devices and appliances. The results are intended to serve as a preliminary indication of their acceptability with respect to flammability for a particular application. The final acceptance of the material is dependent upon its use in complete equipment that conforms with the standard applicable to such equipment. The classification system described in Appendix X1 is intended for quality a Close

RM 30.00

Document will be sent via email



 Add To Cart
TEST METHOD FOR MEASURING THE COMPARATIVE BURNING CHARACTERISTICS OF SOLID PLASTICS IN A VERTICAL POSITION (FIRST REVISION)
MS 2359:2010
Status : 1st Revision
Format : PDF

This Malaysian Standard fire-test-response standard covers a small-scale laboratory procedure for determining comparative burning characteristics of solid-plastic material, using a 20-mm (50W) premixe ....Read more d flame applied to the base of specimens held in a vertical position. NOTE 1—This test method and the 20 mm (50W) Vertical Burning Test (V-0, V-1, or V-2) of ANSI/UL 94 are equivalent. NOTE 2—This test method and Test Method B of IEC 60695–11–10 are equivalent. IEC 60695–11–10 has replaced ISO 1210. NOTE 3—For additional information on materials that burn up to the holding clamp by this test method, see Test Method D 635. For test methods of flexible plastics in the form of thin sheets and film, see Test Method D 4804. For additional information on comparative burning characteristics and resistance to burn-through, see Test Method D 5048. This test method was developed for polymeric materials used for parts in devices and appliances. The results are intended to serve as a preliminary indic Close

RM 30.00

Document will be sent via email



 Add To Cart
FAT AND OIL DERIVATIVES - FATTY ACID METHYL ESTERS (FAME) - DETERMINATION OF POTASSIUM CONTENT BY ATOMIC ABSORPTION SPECTROMETRY
MS 2358:2010
Status : Original
Format : PDF

This Malaysian Standard specifies a method for the determination of potassium contents equal to or greater than 0.5 mg/kg. This standard is applicable to fatty acid methyl esters intended for additio ....Read more n to mineral oils. WARNING-The use of this method may involve hazardous equipment,materials and operations. This Malaysian Standard does not purport to address to all of the safety problems associated with its use, but it is the responsibility of the user to search and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • ...
  • 587
  • 588
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.