• :  
BM ENG
  • Subscription
  • MS Catalogue
  • MS Pack
  • Purchase History
  • Cart
  • Hi
    !
    • My Profile
    • Portal
    • Log Out

Modal title

Widget settings form goes here

Search Malaysian Standard (MS)
 Advanced Search Search

Steel wire for the reinforcement of concrete products - Specification (Fourth revision)
MS 144:2014
Status : 3rd Revision
Format : PDF

This Malaysian Standard specifies requirements for plain, indented and ribbed steel wire used for the reinforcement of concrete products.

This standard contains provisions for two grades, ....Read more based on mechanical properties. Grade 500 is specified for plain, indented and ribbed wires. Grade 250 is specified as an option for plain wires only. Close

RM 60.00

Document will be sent via email



 Add To Cart
Ballasts for tubular fluorescent lamps - Performance (watt loss) requirements (Second revision)
MS 141:2014
Status : 2nd Revision
Format : PDF

This Malaysian Standard specifies performance requirements for ballasts loss excluding resistance types, for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, associated with tubular fluorescent l ....Read more amps with pre-heated cathodes operated with or without a starter or starting device and having rated wattages, dimensions and characteristics as specified in MS IEC 60081 and MS IEC 60901. Close

RM 15.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR PVC-INSULATED CABLES FOR SWITCHGEAR AND CONTROL GEAR WIRING
MS 137:1973
Status : Original
Format : PDF

This Malaysian Standard specifies performance requirements for ballasts loss excluding resistance types, for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, associated with tubular fluorescent l ....Read more amps with pre-heated cathodes operated with or without a starter or starting device and having rated wattages, dimensions and characteristics as specified in MS IEC 60081 and MS IEC 60901. Close

RM 30.00

Document will be sent via email



 Add To Cart
LATEX EMULSION PAINT FOR EXTERIORAND INTERIOR USE – SPECIFICATION (THIRD REVISION)
MS 134:2007
Status : 3rd Revision
Format : PDF

This Malaysian Standard specifies an air-drying latex emulsion paint including textured finish suitable for exterior and interior use on masonry surfaces including concrete, brick, stucco, concrete bl ....Read more ock and asbestos cement shingles and sidings, and for recoating of previously painted surface provided the surface is in sound condition and suitable for receiving such a coating. It may also be used on suitably primed metal and wood surfaces.

NOTE. Paints specifically for interior use only are covered by MS 903:1984, Specification for latex emulsion paint for interior use. Close

RM 15.00

Document will be sent via email



 Add To Cart
METHODS OF TEST FOR PAINTS AND VARNISHES : PART E14 : DETERMINATION OF RESISTANCE TO ABRASION (ROTATING ABRASIVE-PAPER-COVERED WHEEL) (ISO 7784-1:1997, MOD)
MS 133: PART E14:2002 (CONFIRMED:2011)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard is one of a series of standards dealing with the sampling and testing of paints, varnishes and related products.

This Malaysian Standard specifies a method for det ....Read more ermining the resistance to abrasion of a dried film of paint, varnish or related product, using abrasive paper attached to wheels and abrading by making a rotary movement. Close

RM 15.00

Document will be sent via email



 Add To Cart
METHODS OF TEST FOR PAINTS AND VARNISHES : PART D11 : COLORIMETRY - CALCULATION OF COLOUR DIFFERENCES (ISO 7724/3 : 1984, IDT)
MS 133: PART D11:1999 (CONFIRMED:2011)
Status : 1st Confirmation
Format : PDF

This part of MS 133 : Part D11 describes a method for the quantitative colorimetric evaluation of small colour differences between paint films.

NOTE. There are numerous formula for calcul ....Read more ating a colour difference from the colour co-ordinates of twospecimens. For various reasons the results given by such formula, including the one defined here, do not in all casesagree satisfactorily with visual perception nor are they likely to agree with each other. The Commission Internationalede l'Eclairage (CIE) recommended in 1976 two formula for general use. One of these, the CIE 1976 (L*a*b*) colourdifference formula (see CIE Publication No. 15 Supplement No. 2), has proved to be of practical value for thecolorimetric evaluation of paint films and is specified for this application in the parts of MS 133 : Part D9, Part D10and Part D11. Close

RM 15.00

Document will be sent via email



 Add To Cart
METHODS OF TEST FOR PAINTS AND VARNISHES : PART D4 : COMPARISON OF CONTRAST RATIO (HIDING POWER) OF PAINTS OF THE SAME TYPE AND COLOUR (FIRST REVISION) [ISO 2814 : 1973, MOD]
MS 133: PART D4:1998 (CONFIRMED:2020)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies the standard method to be used in comparing the contrastratios given by paint films of white or light colours, of reflectance factor greater than 40 %,dried at normal ....Read more air temperatures and applied at approximately equal wet film thickness to black and white substrates.

The method, comparison of contrast ratio of films drawn down on a black and white substrateat equal wet film thickness, is the simplest of those investigated and has been found to give are producible comparison for paints of similar type. Because different operators using the same film coating device obtain films differing significantly in thickness, probably due tovariation in pressure on the applicator, the method is not satisfactory as an absolute method for the determination of hiding power. Alternative techniques for test film preparation and measurement are specified; MS 133 : Part D6 deals with application to black and white charts, while MS 133 : Part D7 deals with application to Close

RM 15.00

Document will be sent via email



 Add To Cart
METHODS OF TEST FOR PAINTS AND VARNISHES: PART B8: DETERMINATION OF SOLUBLE CADMIUM CONTENT - FLAME ATOMIC ABSORPTION SPECTROMETRIC METHOD AND POLAROGRAPHIC METHOD (ISO 3856/4: 1984, IDT)
MS 133: PART B8:1999 (CONFIRMED:2011)
Status : Withdrawn
Format : PDF

This part of Malaysian Standard describes two methods for the determination of the cadmium content of the test solutions prepared according to MS 1431 or other suitable Malaysian Standards.

....Read more /> The methods are applicable to paint shaving “soluble” cadmium contents in the range of about 0.05 to 5% (m/m).

The flame atomic absorption spectrometric method (AAS) (Clause 3) should be used as the referee method in cases of dispute. Other methods can be used by agreement between the interested parties. A polarographic method is given in Clause 4. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



METHODS OF TEST FOR PAINTS AND VARNISHES PART A13: DETERMINATION OF FLOW TIME BY USE OF ISO 2431 FLOW CUPS
MS 133: PART A13:1994 (CONFIRMED:2011)
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies a method for the determination of the flow time of paints, varnishes and related products that may be used to control consistency. It is recognized that the flow time ....Read more s are reproducible only for products of Newtonian or near- Newtonian flow properties. This effectively limits their practical use. Nevertheless, for checking purposes, these flow cups do serve a useful purpose. Furthermore, the measurement of flow time is often used to confirm the application consistency. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



METHODS OF TEST FOR PAINTS AND VARNISHES: PART B4: DETERMINATION OF TOTALLEAD BY FLAME ATOMIC ABSORPTION SPECTROMETRIC METHOD (FIRST REVISION)
MS 133: PART B4:1997 (CONFIRMED:2011)
Status : Withdrawn
Format : PDF

This Malaysian Standard describes a flame atomic absorption spectrometric method for the determination of total lead in paints and related products.

The method is applicable to products h ....Read more aving total lead contents in the range of about 0.01 to2% (m/m) (Note 1).

Two methods are given for the treatment of the test portion; the dry ashing method (Clause 4) should be used as the referee method in cases of dispute.

For the determination of lead in the test solution, the dithizone spectrophotometric method specified in MS 133 : Part B5 may be used as an alternative method.

NOTE 1. This method may also be applicable to products with a total lead content of more than 2 % (m/m), but itshould only be used when the precision does not exceed the appropriate values given in Clause 7.2. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



  • ‹
  • 1
  • 2
  • ...
  • 539
  • 540
  • 541
  • 542
  • 543
  • 544
  • 545
  • ...
  • 580
  • 581
  • ›