• :  
BM ENG
  • Subscription
  • MS Catalogue
  • MS Pack
  • Purchase History
  • Cart
  • Hi
    !
    • My Profile
    • Portal
    • Log Out

Modal title

Widget settings form goes here

Search Malaysian Standard (MS)
 Advanced Search Search

Soda ash (sodium carbonate) for use in potable water supply – Specification (First revision)
MS 1551:2021
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies requirements for soda ash for use in potable water supply service.
The main purpose of this standard is to provide purchasers, manufacturers, and suppliers wit ....Read more h the minimum requirements for soda ash, including physical, chemical, packaging, transportation and testing requirements. It also gives information on the application and safe handling of this chemical. Close

RM 45.00

Document will be sent via email



 Add To Cart
Sistem pengurusan kesihatan dan keselamatan pekerjaan – Keperluan dengan panduan penggunaan (ISO 45001:2018, IDT) (Diterbitkan oleh Jabatan Standard Malaysia pada tahun 2021)
MS ISO 45001:2018 (BM)
Status : Original
Format : PDF

Dokumen ini menetapkan keperluan untuk sistem pengurusan kesihatan dan keselamatan pekerjaan (KKP), dan memberikan panduan bagi penggunaannya, untuk membolehkan organisasi menyediakan tempat kerja yan ....Read more g selamat dan sihat dengan mencegah kecederaan dan permasalahan kesihatan berkaitan kerja, dan juga dengan memperbaik prestasi KKP secara proaktif.

Dokumen ini boleh digunakan oleh mana-mana organisasi yang ingin mewujudkan, melaksanakan dan menyelenggara sistem pengurusan KKP untuk menambah baik kesihatan dan keselamatan pekerjaan, menghapuskan hazard dan meminimumkan risiko KKP (termasuk kekurangan sistem), memanfaatkan peluang KKP, dan menangani ketakpatuhan sistem pengurusan KKP yang berkaitan dengan aktivitinya.

Dokumen ini membantu organisasi untuk mencapai hasil yang diingini daripada sistem pengurusan KKP. Selari dengan dasar KKP organisasi, hasil yang diingini daripada sistem pengurusan KKP termasuk:

a) penambahbaikan berterusan prestasi KKP;
b) memenuhi keperluan undang-undang dan keperluan lain;
c) pencapaian objektif KKP. Close

RM 90.00

Document will be sent via email



 Add To Cart
Medical face masks - Requirements and test methods
MS EN 14683:2021
Status : Original
Format : PDF

This document specifies construction, design, performance requirements and test methods for medical face masks intended to limit the transmission of infective agents from staff to patients during surg ....Read more ical procedures and other medical settings with similar requirements. A medical face mask with an appropriate microbial barrier can also be effective in reducing the emission of infective agents from the nose and mouth of an asymptomatic carrier or a patient with clinical symptoms.

This European Standard is not applicable to masks intended exclusively for the personal protection of staff.

NOTE 1 Standards for masks for use as respiratory personal protective equipment are available.

NOTE 2 Annex A provides information for the users of medical face masks. Close

RM 45.00

Document will be sent via email



 Add To Cart
Self-ballasted LED-lamps for general lighting services by voltage >50 V - Safety specifications (First revision) (IEC 62560:2011+AMD1:2015, IDT)
MS IEC 62560:2021
Status : 1st Revision
Format : PDF

This International Standard specifies the safety and interchangeability requirements, together with the test methods and conditions required to show compliance of LED-lamps with integrated means for s ....Read more table operation (self-ballasted LED-lamps), intended for domestic and similar general lighting purposes, having:

– a rated wattage up to 60 W;
– a rated voltage of > 50 V up to 250 V;
– caps according to Table 1.

The requirements of this standard relate only to type testing. Recommendations for whole product testing or batch testing are identical to those given in Annex C of IEC 62031.

NOTE 1 Where in this standard the term “lamp(s)” is used, it is understood to stand for “self-ballasted LEDlamp(s)”, except where it is obviously assigned to other types of lamps.

NOTE 2 This standard includes
photobiological safety. Close

RM 60.00

Document will be sent via email



 Add To Cart
LED Modules for General Lighting – Safety Specification (First revision) (IEC 62031:2018, IDT)
MS IEC 62031:2021
Status : 1st Revision
Format : PDF

International Standard IEC 62031 has been prepared by subcommittee 34A: Lamps, of IEC technical committee 34: Lamps and related equipment.

This second edition cancels and replaces the ....Read more first edition published in 2008, Amendment 1:2012 and Amendment 2:2014.

This edition constitutes a technical revision.

This edition includes the following significant technical changes with respect to the previous edition:

a) the scope was clarified as well as the wording in several other clauses;

b) the normative references were updated;

c) the definitions for "replaceable LED module", "non-replaceable LED module" and "nonuser replaceable LED module" were introduced while other definitions covered by IEC 62504 have been removed;

d) the marking clause was restructured and a table added to provide an informative overview;

e) the marking requirements for built-in LED modules were changed;

f) the entry for the marking with the working voltage was revised;

g) the provisions for terminals and heat management were revised;

h) Annex B was deleted;

i) information for luminaire design with regard to working voltage and water contact was introduced;

j) an abnormal temperature test was introduced. Close

RM 60.00

Document will be sent via email



 Add To Cart
Self-ballasted LED-lamps for general lighting services with supply voltages >50 V - Performance requirements (First revision) (IEC 62612:2013, AMD.2:2018, IDT)
MS IEC 62612:2021
Status : 1st Revision
Format : PDF

This International Standard specifies the performance requirements, together with the test methods and conditions, required to show compliance of LED lamps with integral means for stable operation, in ....Read more tended for domestic and similar general lighting purposes, having:

• a rated power up to 60 W;
• a rated voltage of > 50 V a.c. up to 250 V a.c.;
• a lamp cap as listed in IEC 62560.

These performance requirements are additional to the safety requirements in IEC 62560.

The only feature provided by this standard, when applied for replacement purposes, is
information on maximum lamp outlines.

The requirements of this standard relate to type testing. This standard covers LED lamps that intentionally produce white light, based on inorganic LEDs. Close

RM 75.00

Document will be sent via email



 Add To Cart
Adjustable telescopic steel props – Product specifications, design and assessment by calculation and test (First revision)
MS EN 1065:2021
Status : 1st Revision
Format : PDF

This European Standard specifies materials, design requirements, corrosion protection alternatives together with assessment methods using both calculations and testing for open thread and covered thre ....Read more ad adjustable telescopic steel props which are intended for use on construction sites (see Figure 1).

It specifies five classes of nominal characteristic strengths for adjustable telescopic steel props each having a series of maximum extended lengths. Each having differing endplate configuration.

This European Standard does not apply to adjustable props of different materials or construction, nor does it provide any information concerning the use of adjustable steel props. Close

RM 60.00

Document will be sent via email



 Add To Cart
Electric vehicle conductive charging system – Part 24: Digital communication between a d.c. EV charging station and an electric vehicle for control of d.c. charging (IEC 61851-24:2014, IDT)
MS IEC 61851-24:2021
Status : Original
Format : PDF

This part of IEC 61851, together with IEC 61851-23, applies to digital communication between a d.c. EV charging station and an electric road vehicle (EV) for control of d.c. charging, with an a.c. or ....Read more d.c. input voltage up to 1 000 V a.c. and up to 1 500 V d.c. for the conductive charging procedure.

The EV charging mode is mode 4, according to IEC 61851-23. The charging station supplied by high voltage a.c. supply is not covered by this standard.

Annexes A, B, and C give descriptions of digital communications for control of d.c. charging specific to d.c. EV charging systems A, B and C as defined in Part 23. Close

RM 60.00

Document will be sent via email



 Add To Cart
Electric vehicle conductive charging system – Part 23: DC electric vehicle charging station (IEC 61851-23:2014, IDT)
MS IEC 61851-23:2021
Status : Original
Format : PDF

This part of IEC 61851, together with IEC 61851-1:2010, gives the requirements for d.c. electric vehicle (EV) charging stations, herein also referred to as "DC charger", for conductive connection to t ....Read more he vehicle, with an a.c. or d.c. input voltage up to 1 000 V a.c. and up to 1 500 V d.c. according to IEC 60038.

NOTE 1 This standard includes information on EV for conductive connection, but limited to the necessary content for describing the power and signaling interface.

This part covers d.c. output voltages up to 1 500 V.

Requirements for bi-directional power flow are under consideration.

NOTE 2 Typical diagrams and variation of d.c. charging systems are shown in Annex DD.

This standard does not cover all safety aspects related to maintenance.

This part specifies the d.c. charging systems A, B and C as defined in Annexes AA, BB and CC.

NOTE 3 Typical configuration of d.c. EV charging system is shown in Annex EE.

EMC requirements for d.c. EV charging stations are defined in IEC 61851-21-2.

This standard provides the general requirements for the control communication between a d.c. EV charging station and an EV. The requirements for digital communication between d.c. EV charging station and electric vehicle for control of d.c. charging are defined in IEC 61851-24. Close

RM 135.00

Document will be sent via email



 Add To Cart
Electric vehicle conductive charging system – Part 21-2: Electric vehicle requirements for conductive connection to an AC/DC supply – EMC requirements for off-board electric vehicle charging systems (IEC 61851-21-2:2018, IDT) (First revision)
MS IEC 61851-21-2:2021
Status : 1st Revision
Format : PDF

This part of IEC 61851 defines the EMC requirements for any off-board components or equipment of such systems used to supply or charge electric vehicles with electric power by conductive power transfe ....Read more r (CPT), with a rated input voltage, according to IEC 60038:2009, up to 1 000 V AC or 1 500 V DC and an output voltage up to 1 000 V AC or 1 500 V DC.

This document covers off-board charging equipment for mode 1, mode 2, mode 3 and mode 4 charging as defined in IEC 61851-1:2017.

Cables where there is no electronics or no electric/electronic switching are considered as passive (benign) and are deemed to comply with the emission and immunity requirements of this document without any need for testing.

This document does not apply to any on-board components or equipment of charging or power supply systems being part of the vehicles. The EMC requirements for such equipment are covered by IEC 61851-21-1: 2017.

Compliance with the emission and immunity requirements of this document is verified where it can be demonstrated that the equipment under test (EUT) meets the respective limits, during type tests in the measuring arrangement of this document.

Requirements for electric vehicle wireless power transfer (WPT) systems are covered in IEC 61980 (all parts). Close

RM 90.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • ...
  • 580
  • 581
  • ›