• :  
BM ENG
  • Subscription
  • MS Catalogue
  • MS Pack
  • Purchase History
  • Cart
  • Hi
    !
    • My Profile
    • Portal
    • Log Out

Modal title

Widget settings form goes here

Search Malaysian Standard (MS)
 Advanced Search Search

PROTECTIVE CLOTHING – GENERAL REQUIREMENTS (ISO 13688:1998, IDT)
MS ISO 13688 : 2004
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies general requirements and recommendations for ergonomics, ageing, sizing and marking of protective clothing, and for information supplied by the manufacturer.

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



NATURAL GAS – QUALITY DESIGNATION (ISO 13686:1998, IDT)
MS ISO 13686:2005 (CONFIRMED:2011)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies the parameters required to describe finally processed and, where required, blended natural gas. Such gas is referred to subsequently in this text simply as “natural ....Read more gas”. 
The main text of this standard contains a list of these parameters, their units and references to measurement standards. Informative annexes give examples of typical values for these parameters, with the main emphasis on health and safety.

In defining the parameters governing composition, physical properties and trace constituents, consideration has also been given to existing natural gases to ensure their continuing viability.

The question of interchangeability is dealt with in annex A clause A.2 Close

RM 90.00

Document will be sent via email



 Add To Cart
Plastics - Determination of fracture toughness (G(IC) and K(IC)) - Linear elastics fracture mechanics (LEFM) approach (ISO 13586:2000, IDT)
MS ISO 13586:2003, AMD. 1:2013
Status : Amendment 1
Format : PDF

This Malaysian Standard specifies the principles for determining the fracture toughness of plastics in the crack-opening mode (mode I) under defined conditions. Two test methods with cracked specimens ....Read more are defined, namely three-point-bending tests and compact-specimen tensile tests in order to suit different types of equipment available or different types of material. 
The methods are suitable for use with the following range of materials:

- rigid and semi-rigid thermoplastic moulding, extrusion and casting materials;
- rigid and semi-rigid thermosetting moulding and casting materials.

Certain restrictions on the linearity of the load-displacement diagram, on the specimen width and on the thickness are imposed to ensure validity (see6.4) since the scheme used assumes linear elastic behaviour of the cracked material and a state of plane strain at the crack tip. Finally, the crack must be sharp enough so that an even sharper crack will not result in significantly lower values of the Close

FREE

Document will be sent via email



 Send To Email
PLASTICS – DETERMINATION OF FRACTURE TOUGHNESS(G(IC) AND K(IC)) – LINEAR ELASTICS FRACTURE MECHANICS (LEFM) APPROACH (ISO 13586: 2000, IDT)
MS ISO 13586:2003
Status : Original
Format : PDF

This Malaysian Standard specifies the principles for determining the fracture toughness of plastics in the crack-opening mode (mode I) under defined conditions. Two test methods with cracked specimens ....Read more are defined, namely three-point-bending tests and compact-specimen tensile tests in order to suit different types of equipment available or different types of material. 
Themethodsaresuitableforusewiththefollowingrangeofmaterials:

- rigid and semi-rigid thermoplastic moulding, extrusion and casting materials;

- rigid and semi-rigid thermosetting moulding and casting materials.

Certain restrictions on the linearity of the load-displacement diagram, on the specimen width and on the thickness are imposed to ensure validity (see6.4) since the scheme used assumes linear elastic behaviour of the cracked material and a state of plane strain at the crack tip. Finally, the crack must be sharp enough so that an even sharper crack will not result in significantly lower values of the measured p Close

RM 45.00

Document will be sent via email



 Add To Cart
PAPER AND BOARD - SPECIFICATION FOR INTERNAL DIAMETERS OF CORES FOR REELS (ISO 13542:2006, IDT)
MS ISO 13542:2007 (CONFIRMED:2023)
Status : 2nd Confirmation
Format : PDF

This Malaysian Standard specifies the internal diameters and tolerances for cores recommended for general use with reels of paper and board in international trade.

RM 15.00

Document will be sent via email



 Add To Cart
Statistical methods for use in proficiency testing by interlaboratory comparison (ISO 13528:2015, IDT) (Published by Standards Malaysia in 2017)
MS ISO 13528:2017
Status : Original
Format : PDF

This Malaysian Standard provides detailed descriptions of statistical methods for proficiency testing providers to use to design proficiency testing schemes and to analyse the data obtained from those ....Read more schemes. 
It provides recommendations on the interpretation of proficiency testing data by participants in such schemes and by accreditation bodies. Close

RM 150.00

Document will be sent via email



 Add To Cart
Meat and meat products - Detection of colouring agents - Method using thin-layer chromatography (ISO 13496:2000, IDT)
MS ISO 13496:2012
Status : Original
Format : PDF

This Malaysian Standard specifies a thin-layer chromatographic method for the detection of synthetic, watersoluble colouring agents in meat and meat products.

RM 30.00

Document will be sent via email



 Add To Cart
Medical devices - Quality management systems - Requirements for regulatory purposes (First revision) (ISO 13485:2016, IDT)
MS ISO 13485:2017
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies requirements for a quality management system where an organization needs to demonstrate its ability to provide medical devices and related services that consistently ....Read more meet customer and applicable regulatory requirements. Such organizations can be involved in one or more stages of the life-cycle, including design and development, production, storage and distribution, installation, or servicing of a medical device and design and development or provision of associated activities (e.g. technical support). 
This Malaysian Standard can also be used by suppliers or external parties that provide product, including quality management system-related services to such organizations. Close

RM 75.00

Document will be sent via email



 Add To Cart
Medical devices - Quality management systems - Requirements for regulatory purposes (Including COR. 1:2009) (ISO 13485:2003, IDT)
MS ISO 13485:2006 (CONFIRMED:2013)
Status : Withdrawal with replacement
Format : PDF

This Malaysian Standard specifies requirements for a quality management system that can be used by an organization for the design and development, production, installation and servicing of medical dev ....Read more ices, and the design, development, and provision of related services. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



Road vehicles - Ignition coils - Electrical characteristics and test methods (ISO 13476:1997, COR. 1:1999, IDT)
MS ISO 13476:2009 (CONFIRMED:2016)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard applies to ignition coils for inductive energy storage. It defines test methods for ignition coils used in ignition systems with solid state switching of spark ignited internal ....Read more combustion engines. Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • ...
  • 580
  • 581
  • ›