Power transformers - Part 3: Insulation levels, dielectric tests and external clearances in air (IEC 60076-3: 2000, IDT)
MS IEC 60076-3:2005 (CONFIRMED:2013)Status : 1st Confirmation
Format : PDF
his Malaysian Standard applies to single-phase and three-phase oil-immersed power transformers (including auto-transformers), with the exception of certain small and special transformers, as defined i ....Read more
Power transformers - Part 4: Guide to the lightning impulse and switching impulse testing - Power transformers and reactors (IEC 60076-4:2002, IDT)
MS IEC 60076-4:2005 (CONFIRMED:2013)Status : 1st Confirmation
Format : PDF
This Malaysian Standard gives guidance and explanatory comments on the existing procedures for
lightning and switching impulse testing of power transformers to supplement the requirements of ....Read more
Power transformers - Part 1: General (First revision) (IEC 60076-1:2011, MOD)
MS 60076-1:2015Status : 1st Revision
Format : PDF
This Malaysian Standard applies to three-phase and single-phase power transformers (including auto-transformers) with the exception of certain categories of small and special transformers. For those c ....Read more
Insulation co-ordination - Part 4: Computational guide to insulation co-ordination and modelling of electrical networks
MS 60071-4:2012Status : Original
Format : PDF
This Malaysian Standard gives guidance on conducting insulation co-ordination studies which propose internationally recognised recommendations - for the numerical modelling of electrical systems, and ....Read more
Insulation co-ordination - Part 5: Procedures for high-voltage direct current (HVDC) converter stations (IEC/TS 60071-5:2002, MOD)
MS 60071-5:2012Status : Original
Format : PDF
This Malaysian Standard specifies guidance on the procedures for insulation co-ordination of high-voltage direct current (HVDC) converter stations, without prescribing standardised insulation levels. ....Read more
NOT FOR SALE
"Please contact us if you are interested to purchase for reference."INSULATION CO-ORDINATION - PART 2: APPLICATION GUIDE (IEC 60071-2:1996, IDT)
MS IEC 60071-2:2009Status : Original
Format : PDF
This Malaysian Standard constitutes an application guide and deals with the selection of insulationlevels of equipment or installations for three-phase electrical systems. Its aim is to give guidance ....Read more
Environmental testing - Part 2-69: Tests - Test TE: Solderability testing, of electronic components for surface mounting devices (SMD) by the wetting balance method (IEC 60068-2-69:1995, IDT)
MS IEC 60068-2-69:2008 (CONFIRMED:2015)Status : 1st Confirmation
Format : PDF
This Malaysian Standard outlines test Te, solder bath wetting balance method and solder globule wetting balance method, applicable for surface mounting devices. These methods determine quantitatively ....Read more
Environmental testing - Part 2: Tests - Test CY: Damp heat, steady state, accelerated test primarily intended for components (IEC 60068-2-67:1995, IDT)
MS IEC 60068-2-67:2008 (CONFIRMED:2015)Status : 1st Confirmation
Format : PDF
This Malaysian Standard provides a standard test procedure for the purpose of evaluating, in an accelerated manner, the resistance of small electrotechnical products, primarily non-hermetically sealed ....Read more
Environmental testing - Part 2-18: Tests - Test R and guidance: Water (IEC 60068-2-18:2000, IDT)
MS IEC 60068-2-18:2008 (CONFIRMED:2015)Status : 1st Confirmation
Format : PDF
This Malaysian Standard specifies methods of test applicable to products which, during transportation, storage or in service, may be subjected to falling drops, impacting water or immersion.
Basic environmental testing procedures - Part 2: Tests - Test M: Low air pressure (IEC 60068-2-13:1983, IDT)
MS IEC 60068-2-13:2008 (CONFIRMED:2015)Status : 1st Confirmation
Format : PDF
This Malaysian Standard deals with low pressure tests at room temperature.