• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Palm plywood - Specification
MS 2629:2018 (CONFIRMED:2025)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies requirements for plywood for general, furniture and structural use, in dry, tropical-dry/humid and high-humidity/exterior conditions. This standard includes requireme ....Read more nts for the quality of veneer, glue-bond, lay-up (construction), dimensions and tolerances, conformance verification (where applicable) and marking. Additional information on supplementary properties for certain applications is also provided. Close

RM 30.00

Document will be sent via email



 Add To Cart
Natural fibre-plastic composite (NFPC) -Test method - Part 2: Decking profiles and tiles
MS 2630:2018
Status : Original
Format : PDF

This Malaysian Standard provides test methods of natural fibre-plastic composite (NFPC), usually called wood-plastic composite (WPC), for decking profiles and tiles used in exterior applications. This ....Read more part of standard will cover the preparation of specimen, test equipment, procedures of measurements and evaluation methods. Close

RM 45.00

Document will be sent via email



 Add To Cart
Surface active agents – Vocabulary (ISO 862:1984 and its technical corrigendum 1:1993, IDT)
MS ISO 862:2005 (CONFIRMED:2025)
Status : 1st Confirmation
Format : PDF

This International Standard defines terms frequently used in the field of surface
active agents

NOTES - Some terms dissociated or not from their definition can appear as commerci ....Read more al terms according to their usage or to their mode of presentation; under no circumstances may their definitions be used as reference definitions for the commercial terms.
Other terms which appear non-specific to surface active agents, are nevertheless
widely used in this field.

This International Standard gives, in particular, specific terms for textiles applications, dry cleaning, etc., but terms for other applications may be introduced.
These terms are grouped according to the classification shown below. Close

RM 105.00

Document will be sent via email



 Add To Cart
Sodium carbonate for industrial use – Determination of total soluble alkalinity – Titrimetric method (ISO 740:1976, IDT)
MS ISO 740:2003 (CONFIRMED:2014)
Status : 1st Confirmation
Format : PDF

This International Standard specifies a titrimetric method
for the determination of the total soluble alkalinity of sodium carbonate for industrial use.

RM 15.00

Document will be sent via email



 Add To Cart
Analysis of soaps - Determination of total alkali content and total fatty matter content (ISO 685:1975, IDT)
MS ISO 685:2006 (CONFIRMED:2025)
Status : 2nd Confirmation
Format : PDF

This International Standard specifies a method for the simultaneous determination of the total alkali (l) content and the total fatty matter content of soaps, excluding compounded products.

....Read more /> This method for the determination of total alkali is not applicable to coloured soaps if the colour interferes with the methyl orange end-point. Close

RM 15.00

Document will be sent via email



 Add To Cart
Soaps – Determination of content of ethanol-insoluble matter (ISO 673:1981, IDT)
MS ISO 673:2004 (CONFIRMED:2025)
Status : 2nd Confirmation
Format : PDF

This International Standard specifies a method for the determination of the content of ethanol insoluble matter in commercial soaps, excluding compounded products.

RM 15.00

Document will be sent via email



 Add To Cart
Soaps - Determination of moisture and volatile matter content – Oven method (ISO 672:1978, IDT)
MS ISO 672:2006 (CONFIRMED:2025)
Status : 2nd Confirmation
Format : PDF

This International Standard specifies an oven method for the determination of the moisture and volatile matter content of commercial soaps, excluding compounded
products.

NOTE - ....Read more Attention is drawn to IS0 4318 which specifies an azeotropic distillation method for etermination of water content. Close

RM 15.00

Document will be sent via email



 Add To Cart
Surface active agents and detergents – Methods of sample division (ISO 607:1980, IDT)
MS ISO 607:2004 (CONFIRMED:2025)
Status : 2nd Confirmation
Format : PDF

This International Standard specifies methods for obtaining a reduced sample of surface active agent or detergent suitable for use with single or mixed products, in the form of powders, pastes or liqu ....Read more ids.

The sample reduction process may be required for the following reasons :
a) the preparation of a final sample or a laboratory sample of mass greater than 250 g from a blended bulk sample of mass greater than 500 g;
b) the preparation of several equivalent laboratory samples and/or reference samples and/or storage samples, each of mass greater than 250 g, from a final sample;
c) the preparation of a test sample from a laboratory sample Close

RM 15.00

Document will be sent via email



 Add To Cart
Surface active agents – Analysis of soaps – Determination of free caustic alkali (ISO 456:1973, IDT)
MS ISO 456:2005 (CONFIRMED:2025)
Status : 2nd Confirmation
Format : PDF

This International Standard specifies two methods of determining free caustic alkali in commercial soaps, excluding compounded products :
-- Method A, ethanol method;
- Method B, barium ....Read more chloride method. Close

RM 15.00

Document will be sent via email



 Add To Cart
Fine ceramics (advanced ceramics, advanced technical ceramics) – Test method for shear strength of continuous fiber reinforced advanced ceramics at ambient temperatures
MS 1983:2007 (CONFIRMED:2014)
Status : 1st Confirmation
Format : PDF

1.1 This test method covers the determination of shear strength of continuous fiber-reinforced ceramic composites (CFCCs)
at ambient temperature. The test methods addressed are (1) the compressi ....Read more on of a double-notched specimen to determine
interlaminar shear strength and (2) the Iosipescu test method to determine the shear strength in any one of the material planes
of laminated composites. Specimen fabrication methods, testing modes (load or displacement control), testing rates (load rate
or displacement rate), data collection, and reporting procedures are addressed.
1.2 This test method is used for testing advanced ceramic or glass matrix composites with continuous fiber reinforcement
having uni-directional (1-D) or bi-directional (2-D) fiber architecture. This test method does not address composites with (3-D)
fiber architecture or discontinuous fiber-reinforced, whisker-reinforced, or particulate-reinforced ceramics.
1.3 The values stated in SI units are to be regarded as the standard and are in accordance with IEEE/ASTM SI 10.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of
regulatory limitations prior to use. Specific hazard statements are given in 8.1 and 8.2. Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 579
  • 580
  • 581
  • 582
  • 583
  • 584
  • 585
  • ...
  • 588
  • 589
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.