• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • Sign In
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Rubber, vulcanized or thermoplastic - Determination of tensile stress-strain properties (Third revision) (ISO 37:2017, IDT)
MS ISO 37:2019
Status : 3rd Revision
Format : PDF

This document specifies a method for the
etermination of the tensile stress-strain properties of vulcanized and thermoplastic rubbers. The properties which can be determined are tensile streng ....Read more th, elongation at break, stress at a given
elongation, elongation at a given stress, stress at yield and elongation at yield. The measurement of stress and strain at yield applies only to some thermoplastic rubbers and certain other compounds. Close

RM 60.00

Document will be sent via email



 Add To Cart
Rubber and rubber products - Determination of 2,2-bis(4-hydroxyphenyl)propane [Bisphenol A] (BPA) by using high performance liquid chromatography (HPLC)
MS 2625:2016
Status : Original
Format : PDF

This Malaysian Standard provides a method for the determination of 2,2-bis(4-
hydroxyphenyl)propane [Bisphenol A] (BPA) in rubber and rubber products (for example
natural rubber (NR) glove ....Read more s, synthetic gloves, child use and care articles) by using high
performance liquid chromatography (HPLC) technique.
NOTE Bisphenol A (BPA) is a carbon-based synthetic compound with the chemical formula
(CH3)2C(C6H4OH)2 belonging to the group of diphenyl methane derivatives and bisphenols, with two
hydroxyphenyl groups. BPA is known to be used as an additive to make polycarbonate plastics and
epoxy resins. Close

RM 15.00

Document will be sent via email



 Add To Cart
Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Polypropylene (PP) (First revision) (ISO 7671:2003, IDT)
MS ISO 7671:2012 (CONFIRMED:2018)
Status : 1st Revision
Format : PDF

This International Standard specifies the requirements for solid-wall polypropylene (PP) pipes and fittings for soil and waste discharge (low and high temperature) inside buildings, as well as the sys ....Read more tem itself. It does not include buried pipework.
It also specifies the test parameters for the test methods referred to in this International Standard.
This International Standard is applicable to PP pipes and fittings, as well as assemblies of such pipes and fittings, intended to be used for the following purposes:
a) soil and waste discharge pipework for the conveyance of domestic waste waters (low and high temperature);
b) ventilation pipework associated with a);
c) rainwater pipework inside the building.
It is applicable to pipes and fittings for jointing by means of elastomeric sealing rings or by butt fusion. Close

RM 60.00

Document will be sent via email



 Add To Cart
PLASTICS - DETERMINATION OF FRACTURE TOUGHNESS (GIC AND KIC) AT MODERATELY HIGH LOADING RATES (1 m/s) (ISO 17281:2002, IDT)
MS ISO 17281:2004 (CONFIRMED:2018)
Status : 1st Confirmation
Format : PDF

This International Standard provides guidelines for determining the fracture toughness of plastics in the crack- opening mode (Mode I) by a linear elastic fracture mechanics (LEMF) approach, at load-p ....Read more oint displacement rates of up to 1 m/s. It supplements ISO 13586 so as to extend its applicability to loading rates somewhat higher than is the case in the scope of the latter International Standard.
Fracture testing at high loading rates presents special problems because of the presence of dynamic effects: vibrations in the test system producing oscillations in the recorded quantities, and inertial loads producing forces on the test specimen different from the forces sensed by the test fixture. These effects need either to be controlled and, if possible, reduced by appropriate action, or else to be taken into account through proper analysis of the measured data. Close

RM 45.00

Document will be sent via email



 Add To Cart
Plywood - Specification (Second revision)
MS 228:2015
Status : 2nd Revision
Format : PDF

1.1 This Malaysian Standard specified requirements for plywood for general and structural
use, in dry, tropical dry/humid and high humidity/exterior conditions. This standard includes
requ ....Read more irements for the quality of veneer, glue bond, lay-up (construction), dimensions and
tolerances, conformance verification (where applicable) and marking.
1.2 The values listed in this standard relate to product properties, but these are not
characteristic values to be used in design calculations.
NOTE. Such characteristic values are given by the manufacturer, based on testing according to ISO
16572. Additional information on supplementary properties for certain applications is also given. Close

RM 30.00

Document will be sent via email



 Add To Cart
Code of practice for structural use of timber - Part 11: Recommendations for the calculation basis for span tables - Section 4: Domestic rafters
MS 544-11-4:2015
Status : Original
Format : PDF

This section of MS 544-11 recommends a calculation basis for the permissible clear span for
roof rafter with a slope from 15° to 45°. The recommendations apply to rafters at a maximum
sp ....Read more acing of 1 200 mm centre-to-centre. The method of calculation makes no allowance for any
contribution of other parts of the roof to the load resistance of the rafters although it is
assumed that the tiling battens are capable of providing lateral load distribution and lateral
support.
This section does not cover the design of rafters taking account of a structural contribution by
sheet material supporting the roofing where such action can be provided by adequate design
of its attachments as in a stressed skin panel roof. The uniform and concentrated loads of
Uniform Building By-Laws 1984 are considered. This section also covers the overhang
calculation. Typical examples of roof construction are given in Figures 1 and 2, and examples
of rafters are given in Figure 3.
This section of MS 544-11 is applicable to the species, strength groups and grades of timber
given in MS 544: Part 2:2001. Close

RM 75.00

Document will be sent via email



 Add To Cart
Code of practice for structural use of timber - Part 8: design, fabrication and installation of prefabricated timber roof trusses using toothed metal plate connectors
MS 544-8:2015
Status : Original
Format : PDF

This Malaysian Standard specifies requirements for the design, fabrication and installation of
prefabricated timber roof trusses using toothed metal plate connectors. It is applicable to the
....Read more /> design, fabrication and installation of prefabricated timber roof trusses within the following
general limitations:
a) Maximum clear span 16 m;
b) Maximum recommended truss spacing of:
i) 1 220 mm, for concrete tiles; and
ii) 1 830 mm, for metal sheet roofs.
c) Maximum design wind speed of 35.2 m/s. Close

RM 165.00

Document will be sent via email



 Add To Cart
Timber flooring - Board and strip, parquet and laminate flooring - Specification
MS 2619:2015 (CONFIRMED:2020)
Status : Original
Format : PDF

This Malaysian Standard specifies requirement for the following types of timber flooring:
a) solid board and strip;
b) parquet; and
c) laminate flooring.

RM 30.00

Document will be sent via email



 Add To Cart
Wooden windows - Specifications
MS 2620:2015 (CONFIRMED:2020)
Status : Original
Format : PDF

1.1 This Malaysian Standard specifies requirements for wooden window frames, box frame
windows and their sashes incorporating traditional component sections.
1.2 It does not apply to windo ....Read more w assemblies intended to carry loads transmitted from the
structure into which they are fitted.
1.3 The concept of modular coordination is incorporated in this standard in order to
harmonise with MS 1064.
1.4 Effort is made to classify windows into three categories of Deluxe, Regular and
Economy in line with current pattern of utilisation in the country.
1.5 Minimum dimension is also proposed for certain components used for each category
with the aim to complement the harmonisation effort made. Close

RM 30.00

Document will be sent via email



 Add To Cart
Palm plywood - Specification
MS 2629:2018
Status : Original
Format : PDF

This Malaysian Standard specifies requirements for plywood for general, furniture and structural use, in dry, tropical-dry/humid and high-humidity/exterior conditions. This standard includes requireme ....Read more nts for the quality of veneer, glue-bond, lay-up (construction), dimensions and tolerances, conformance verification (where applicable) and marking.
Additional information on supplementary properties for certain applications is also provided. Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 566
  • 567
  • 568
  • 569
  • 570
  • 571
  • 572
  • ...
  • 576
  • 577
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.