• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly (vinyl chloride) (PVC-U) - Part 1:General (Second Revision) (ISO 1452-1:2009, MOD)
MS 628-1:2014 (CONFIRMED:2019)
Status : 2nd Revision
Format : PDF

This Malaysian Standard specifies the general aspects of unplasticized poly (vinyl chloride) (PVC-U) solid-wall piping systems intended for water supply and for buried and above-ground drainage and se ....Read more werage under pressure.  Close

RM 30.00

Document will be sent via email



 Add To Cart
Plastics piping systems for water supply and for buried and above ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) - (PVC-U) Part 2: Pipes (Second revision) (ISO 1452-2:2009, MOD)
MS 628-2:2014 (CONFIRMED:2019)
Status : 2nd Revision
Format : PDF

This Malaysian Standard specifies the characteristics of solid-wall pipes made from unplasticized poly(vinyl chloride) (PVC-U) for piping systems intended for water supply and for buried and above-gro ....Read more und drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to in this standard.

This standard is intended to be used for the following:

a) water mains and services buried in the ground;
b) conveyance of water above ground for both outside and inside buildings; and
c) buried and above-ground drainage and sewerage under pressure.

It is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. Close

RM 60.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR UNPLASTICISED PVC (uPVC) PIPES FOR WATER SUPPLY: PART 1: PIPES (FIRST REVISION)
MS 628: PART 1:1999
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies the requirements for unplasticised PVC pipes for pressure application for use in cold water services or potable water. The pressure rating of the pipes shall be of PN ....Read more 9, PN 12 or PN 15.

The pipes shall be supplied in standard 6 m lengths with an integral socket formed on one end to provide for jointing by mechanical rubber ring or solvent weld joints. The plain end shall be chamfered to facilitate insertion during jointing and witness mark shall be put at the spigot end of the pipe.

Other lengths may be supplied as agreed upon between purchaser and supplier. The pipes shall conform to the standards as stated unless specifically pecified otherwise.

Rubber ring joints shall be manufactured for pipe sizes of 80 mm and above. For pipe sizes below 80 mm, the plain end or solvent weld joint pipes shall be manufactured. Close

RM 60.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR UNPLASTICISED PVC(uPVC) PIPES FOR WATER SUPPLY: PART 1: PIPES (FIRST REVISION)
MS 628: PART 1:1999, AMD 2:2002
Status : Amendment 2
Format : PDF

This Malaysian Standard specifies the requirements for unplasticised PVC pipes for pressure application for use in cold water services or potable water. The pressure rating of the pipes shall be of PN ....Read more 9, PN 12 or PN 15.  Close

FREE

Document will be sent via email



Please Login to enable MS to be send via email
SPECIFICATION FOR UNPLASTICISED PVC(uPVC) PIPES FOR WATER SUPPLY: PART 1: PIPES (FIRST REVISION)
MS 628: PART 1:1999, AMD 1:2001
Status : Amendment 1
Format : PDF

This Malaysian Standard specifies the requirements for unplasticised PVC pipes for pressure application for use in cold water services or potable water. The pressure rating of the pipes shall be of PN ....Read more 9, PN 12 or PN 15.

The pipes shall be supplied in standard 6 m lengths with an integral socket formed on one end to provide for jointing by mechanical rubber ring or solvent weld joints. The plain end shall be chamfered to facilitate insertion during jointing and witness mark shall be put at the spigot end of the pipe. Other lengths may be supplied as agreed upon between purchaser and supplier. The pipes shall conform to the standards as stated unless specifically specified otherwise.

Rubber ring joints shall be manufactured for pipe sizes of 80 mm and above. For pipe sizes below 80 mm, the plain end or solvent weld joint pipes shall be manufactured. Close

FREE

Document will be sent via email



Please Login to enable MS to be send via email
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 6: Guide for installation
MS 628-6:2015
Status : Original
Format : PDF

This Malaysian Standard set out recommended method of handling and installing unplasticised PVC pipes forwater supply. 

RM 45.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR UNPLASTICISED PVC (uPVC) PIPES FOR WATER SUPPLY: PART 2 :JOINTS AND FITTINGS FOR USE: WITH UNPLASTICISED PVC PIPES: SECTION 2.1: uPVC JOINTS AND FITTINGS
MS 628:PART 2:SECTION 2.1:1999
Status : Original
Format : PDF

This Malaysian Standard specifies the requirements for unplasticised PVC joints and fittings made principally of unplasticised polyvinyl chloride and of which one or more of the joints are intended fo ....Read more r unplasticised PVC pressure pipes complying with MS 628:Part 1.

Joints complying with this standard may be either purpose made socket formed on the pipe complying with MS 628:Part 1, or detachable couplers and other fittings, which are injection moulded. Close

RM 45.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR UNPLASTICISED PVC(uPVC) PIPES FOR WATER SUPPLY : PART 3 : GUIDE FOR INSTALLATION
MS 628 : PART 3 : 1999
Status : Original
Format : PDF

plastics products, pipes, unplasticised PVC, water supply, handling, installation,
transporting, tests, inspection

RM 45.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR UNPLASTICISED PVC (uPVC) PIPES FOR WATER SUPPLY: PART 2: JOINTS AND FITTINGS FOR USE WITH UNPLASTICISED PVC PIPES: SECTION 2.2: SOLVENT CEMENT
MS 628:PART 2:SECTION 2.2:1999
Status : Original
Format : PDF

This Malaysian Standard specifies the requirements for solvent cement, supplied in cans or
tubes for jointing unplasticised PVC pressure pipes complying with the requirements of MS
628: Pa ....Read more rt 1 and MS 762, unplasticised PVC fittings complying with the requirements of BS
4346: Part I and unplasticised PVC pipes and fittings complying with the requirements of BS
5481.
The solvent cement is also suitable, along with solvent cement complying with the
requirements of BS 6209, for jointing products complying with the requirements of BS 4514,
BS 4576: Part I and BS 4660.
NOTE. This standard does not specify the type of can used for solvent cement, but it recommends a colour for the
cans. Close

RM 30.00

Document will be sent via email



 Add To Cart
Plastics piping systems for water Supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Solvent cement
MS 628-4:2015
Status : Original
Format : PDF

This Malaysian Standard specifies the requirements for solvent cement, supplied in cans or tubes for jointing unplasticised PVC pressure pipes complying with the requirements of MS 628:Part 1 and MS 7 ....Read more 62, unplasticised PVC fittings complying with the requirements of BS 4346:Part 1 and unplasticised PVC pipes and fittings complying with the requirements of BS 5481.

The solvent cement is also suitable, along with solvent cement complying with the requirements of BS 6209, for jointing products complying with the requirements of BS 4514, BS 4576:Part 1 and BS 4660.

NOTE. This Malaysian Standard does not specify the type of can used for solvent cement, but it recommends a colour for the cans. Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 503
  • 504
  • 505
  • 506
  • 507
  • 508
  • 509
  • ...
  • 588
  • 589
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.