• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




PVC floor mats for motor vehicles - Specification (First revision)
MS 1470:2011
Status : 1st Revision
Format : PDF

This standard prescribes the specifications for floor mats made of PVC intended for use in motor vehicles.

RM 15.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR PLASTIC LENSES FOR AUTOMOTIVE LAMPS
MS 1469:1999
Status : Original
Format : PDF

This Malaysian Standard prescribes the specifications for the plastic lenses for automotive lamps. It does not specify the complete lamps.

RM 15.00

Document will be sent via email



 Add To Cart
METHOD OF TEST FOR DETERMINATION OF 2 % SECANT MODULUS FOR POLYETHYLENE FILMS
MS 1467:1999 (CONFIRMED:2010)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies a method for calculating the 2 % secant modulus for polyethylene film less than 1.0 mm in thickness.

RM 15.00

Document will be sent via email



 Add To Cart
TEST METHOD FOR LINEAR THERMAL EXPANSION OF SOLID MATERIALS BY THERMOMECHANICAL ANALYSIS (FIRST REVISION)
MS 1466:2007
Status : Withdrawn
Format : PDF

This Malaysian Standard determines the apparent coefficient of linear thermal expansion of solid materials using thermomechanical analysis techniques. 

This test method is applicable ....Read more to solid materials that exhibit sufficient rigidity over the test temperature range such that the sensing probe does not produce indentation of the specimen. 

The recommended lower limit of coefficient of linear thermal expansion measured with this test method is 5 m/(m·°C). The test method may be used at lower (or negative) expansion levels with decreased accuracy and precision (see Section 11). 

This test method is applicable to the temperature range from 120 to 900 °C. The temperature range may be extended depending upon the instrumentation and calibration materials used. 

Computer or electronic based instruments, techniques, or data treatment equivalent to this test method may also be used. 

NOTE 1—Users of this test method are expressly advised that all such instruments or techniques may not be e Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



Test method for DC resistance or conductance of insulating materials (First revision)
MS 1465:2012
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies direct-current procedures for the measurement of dc insulation resistance, volume resistance, and surface resistance. From such measurements and the geometric dimensi ....Read more ons of specimen and electrodes, both volume and surface resistivity of electrical insulating materials can be calculated, as well as the corresponding conductances and conductivities. Close

RM 45.00

Document will be sent via email



 Add To Cart
GREY CAST IRONS - CLASSIFICATION (FIRST REVISION) (ISO 185:2005, MOD)
MS 1463:2008
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies the properties of unalloyed and low-alloyed grey cast irons used for castings, which have been manufactured in sand moulds or in moulds with comparable thermal behavi ....Read more our. 

This Malaysian Standard specifies the characterizing properties of grey cast iron by either 

a) the tensile strength of separately cast samples, or if agreed by the manufacturer and the purchaser, of cast-on samples or samples cut from a casting (see Table 1), or 
b) if agreed between the manufacturer and the purchaser, the hardness of the material measured on castings (see Table 2) or on a cast-on knob. Close

RM 45.00

Document will be sent via email



 Add To Cart
Metal Scaffolding - Part 3: Prefabricated scaffoldings - Section 2: Particular methods of structural design for steel and aluminium modular system scaffoldings
MS 1462-3-2:2012
Status : Original
Format : PDF

This Malaysian standard applies to façade scaffold systems. It also defines the rules for the structural analysis and design of these systems by calculation and testing.

RM 45.00

Document will be sent via email



 Add To Cart
Metal scaffolding - Part 2: Tubular (Tube and coupler scaffolds - Section 2: Specification for aluminium tubes
MS 1462-2-2:2010 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies requirements for the material, dimensions and method of manufacture of extruded aluminium tubes for use in scaffolding. It specifies one grade of material and one ran ....Read more ge of dimensions. Appendix A describes a drift expanding test for extruded aluminium scaffold tubes. Close

RM 15.00

Document will be sent via email



 Add To Cart
Metal scaffolding - Part 4: Temporary works equipments - Section 2: Information on materials
MS 1462-4-2:2013
Status : Original
Format : PDF

This Malaysian Standard provides guidance on where to find information on materials often used in temporary works. It draws attention to a number of points that a designer should take into account. < ....Read more br />
The information given is limited to commonly used steel, aluminium alloys, cast iron, timber and timber based materials. 

Requirements are also given for welding, for limiting corrosion and other deterioration. 

It is limited to the selection of types and grades of material from standards. Close

RM 30.00

Document will be sent via email



 Add To Cart
Metal scaffolding - Part 2: Tubular (tube and coupler) scaffolds - Section 1: Specification for steel tubes
MS 1462-2-1:2010 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies the requirements for non-alloy steel tubes for use with EN 74 couplers in the construction of falsework and working scaffolds. It includes detailed requirements for m ....Read more arking to aid long-term identification, for protective coating, and for inspection and testing. 

NOTE 1: Tubes to this Malaysian Standard, which have a specified outside diameter of 48,3 mm and specified thickness of 3,2 mm or 4,0 mm, may also be used in conjunction with other sizes and grades of steel tubes for applications such as prefabricated scaffolds. 

NOTE 2: The use of these tubes should be in accordance with appropriate International and national requirements, for example prEN 12811 and prEN 12812. Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 409
  • 410
  • 411
  • 412
  • 413
  • 414
  • 415
  • ...
  • 587
  • 588
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.