• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Plastics tableware - Specification (First revision)
MS 1556:2012
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies the requirements for plastics tableware comprising plastics plates, cups, bowls and cutlery. It includes decorated tableware.

RM 30.00

Document will be sent via email



 Add To Cart
Electromagnetic compatibility (EMC) - Limits - Limitation of emission of harmonic currents in low-voltage power supply systems for equipment with rated current greater than 16A
MS 1555:2002 (CONFIRMED:2012)
Status : Original
Format : PDF

This Malaysian Standard deals with the emission of disturbances due to harmonics.

Provision of this Malaysian Standard isapplicable to electrical and electronic equipment with arated inp ....Read more ut current exceeding 16 A per phase and intended to be connected to public low-voltage a.c. distribution systems of the following types:

a) nominal voltage up to 240 V, single-phase, two or three wires;
b) nominal voltage up to 600 V, three-phase, three or four wires; and
c) nominal frequency 50 Hz or 60 Hz.
Other distribution systems are excluded.

Tests according to this standard are type tests of complete pieces of equipment, for example aspeed variable fan, and not of components, for example a converter.

Connection of this equipment to the supply generally requires agreement between the supplyauthority and the consumer. This consent will depend upon several factors including theexpected levels of disturbance caused by the equipment and the actual situation at theconnection point to the pow Close

RM 30.00

Document will be sent via email



 Add To Cart
Code of practice on wind loading for building structure
MS 1553:2002, AMD.1:2013
Status : Amendment 1
Format : PDF

This Malaysian Standard sets out procedures for determining wind speeds and resulting wind actions to be used in the structural design for structures subjected to wind action other than those caused b ....Read more y tornadoes and typhoons.

The standard covers structures within the following criteria:
a) building less than 200 m high;
b) structures with roof spans less than 100 m; and
c) structures other than off-shore structures, bridges and transmission towers. Close

FREE

Document will be sent via email



Please Login to enable MS to be send via email
CODE OF PRACTICE ON WIND LOADING FOR BUILDING STRUCTURE
MS 1553:2002
Status : Original
Format : PDF

This Malaysian Standard sets out procedures for determining wind speeds and resulting wind actions to be used in the structural design for structures subjected to wind action other than those caused b ....Read more y tornadoes and typhoons.The standard covers structures within the following criteria:
a) building less than 200 m high;
b) structures with roof spans less than 100 m; and
c) structures other than off-shore structures, bridges and transmission towers. Close

RM 165.00

Document will be sent via email



 Add To Cart
LIQUID CHLORINE FOR INDUSTRIAL USE – METHOD OF SAMPLING (FOR DETERMINING ONLY THE VOLUMETRIC CHLORINE CONTENT) (ISO 1552:1976, IDT)
MS ISO 1552 : 2003
Status : Original
Format : PDF

This Malaysian Standard specifies a method of sampling liquid chlorine for industrial use, with a view to determining only the volumetric chlorine content.

RM 15.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR RAISED ACCESS FLOOR SYSTEM : PART 1 : GENERAL REQUIREMENTS
MS 1552 : PART 1 : 2002
Status : Original
Format : PDF

This Malaysian Standard sets out the performance requirements for the design and manufacture of access floor systems. It applies to access for systems which are:

a) elevated;

....Read more /> b) full access;

c) square and rectangular shapes; and

d) installed in new and old buildings.

NOTE. Guidelines to purchasers on information to be supplied by the manufacturers are detailed in Appendix A. Close

RM 45.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR RAISED ACCESS FLOOR SYSTEM : PART 2 : TEST METHODS
MS 1552 : PART 2 : 2002
Status : Original
Format : PDF

This Malaysian Standard sets out the test methods required for design and manufacture of access floor system. The test methods prepared in this standard are to be used in conjunction with the requirem ....Read more ents described in MS 1552 : Part 1. Therefore, the user of this Malaysian Standard is advised to refer to MS 1552 : Part 1 for further clarification. The test methods listed in this Malaysian Standard are as follows:

a) Section 2 : Test for concavity and convexity;
b) Section 3 : Test for twist;
c) Section 4 : Test for panel squareness;
d) Section 5 : Test for air leakage rate;
e) Section 6 : Test for the effect of temperature;
f) Section 7 : Test for the effect of humidity;
g) Section 8 : Test for determination of surface spread of flame and index of performance (fire);
h) Section 9 : Test for floor resistance for electrostatic control;
i) Section 10 : Test for 300 mm x 300 mm concentrated load;
j) Section 11 : Test for 25 mm x 25 mm concentrated load;
k) Section 12 : Test for Close

RM 105.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR SODA ASH (SODIUM CARBONATE) USED FOR POTABLE WATER SUPPLY
MS 1551:2002
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies requirements for soda ash for use in potable water supply service . The main purpose of this standard is to provide purchasers, manufacturers, and suppliers with the ....Read more minimum requirements for soda ash, including physical, chemical, packaging, transportation and testing requirements. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



TEST METHOD FOR DETERMINATION OF RESIDUAL POWDER ON POWDERED RUBBER MEDICAL GLOVES
MS 1550 : 2002 (CONFIRMED:2024)
Status : 1st Confirmation
Format : PDF

This standard is designed to determine the amount of residual powder (or filter-retained mass) found on powdered gloves.

RM 15.00

Document will be sent via email



 Add To Cart
TEST METHOD FOR DETERMINATION OF RESIDUAL POWDER ON POWDER -FREE RUBBER MEDICAL GLOVES
MS 1549 : 2002 (CONFIRMED:2024)
Status : 1st Confirmation
Format : PDF

This standard is designed to determine the amount of residual powder (or filter-retained mass) found on gloves described as non-powdered, powder-free, powderless, no powder, or other words to that eff ....Read more ect. Close

RM 15.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 395
  • 396
  • 397
  • 398
  • 399
  • 400
  • 401
  • ...
  • 588
  • 589
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.