• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




THERMOPLASTICS PIPING SYSTEMS – END-LOAD BEARING MECHANICAL JOINTS BETWEEN PRESSURE PIPES AND FITTINGS – TEST METHOD FOR RESISTANCE TO PULL OUT UNDER CONSTANT LONGITUDINAL FORCE
MS 1740:2004
Status : Original
Format : PDF

This Malaysian Standard specifies a method for checking the ability of assembled end-load bearing mechanical joints (excluding fusion-welded joints) between fittings and pressure pipes to withstand a ....Read more longitudinal tensile force. Close

RM 15.00

Document will be sent via email



 Add To Cart
PLASTICS PIPING SYSTEMS – THERMOPLASTICS PIPES AND FITTINGS FOR HOT AND COLD WATER – TEST METHOD FOR THE RESISTANCE OF MOUNTED ASSEMBLIES TO TEMPERATURE CYCLING
MS 1739:2004
Status : Original
Format : PDF

This Malaysian Standard specifies a method for testing the resistance to temperature cycling of joints for piping systems with rigid or flexible thermoplastics pipes.

It is applicable to ....Read more thermoplastics piping systems intended to be used in hot and cold water pressure applications. Close

RM 15.00

Document will be sent via email



 Add To Cart
PLASTICS PIPING SYSTEMS – INJECTION-MOULDED THERMOPLASTICS FITTINGS, VALVES AND ANCILLARY EQUIPMENT – DETERMINATION OF THE LONG-TERM HYDROSTATIC STRENGTH OF THERMOPLASTICS MATERIALS FOR INJECTION MOULDING OF PIPING COMPONENTS
MS 1738:2004
Status : Original
Format : PDF

This Malaysian Standard specifies methods for preparing tubular test pieces for testing thermoplastics materials used for injection moulding, to evaluate the long-term resistance to constant internal ....Read more water pressure at constant temperature and to check the hydrostatic strength of the material. Close

RM 15.00

Document will be sent via email



 Add To Cart
PLASTICS PIPING SYSTEMS – GUIDANCE FOR THE INSTALLATION INSIDE BUILDINGS OF PRESSURE PIPING SYSTEMS FOR HOT AND COLD WATER INTENDED FOR HUMAN CONSUMPTION
MS 1737:2004
Status : Original
Format : PDF

This Malaysian Standard recommends practices to be followed in the application and installation of thermoplastics pipes and associated fittings.These fall within the scope of EN 806-1 and prEN 12731, ....Read more ISO/FDIS 15874, MS 1736, MS ISO 15876 and hot and cold water to be used for hot and/or cold water distribution intended for human consumption inside buildings. This document can also be used for heating installations if applicable, except for under floor heating for which EN 12164 can apply.

Guidance is also given on acceptable methods of jointing polybutylene (PB), crosslinked polyethylene (PE-X), polypropylene (PP) and chlorinated poly(vinyl chloride) (PVC-C) pipes and associated fittings, together with recommendations for their storage, handling and transportation. Close

RM 45.00

Document will be sent via email



 Add To Cart
PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS – CROSSLINKED POLYETHYLENE (PE-X): PART 2: PIPES (ISO 15875-2:2002, MOD)
MS 1736: PART 2:2004
Status : Original
Format : PDF

This Malaysian Standard specifies the characteristics of pipes made from crosslinked polyethylene (PE-X) for piping systems intended to be used for hot and cold water installations within buildings fo ....Read more r the conveyance of water, whether or not intended for human consumption (domestic systems), and for heating systems, under design pressures and temperatures appropriate to the class of application (see Table 1 of MS 1736: Part 1).

This standard covers a range of service conditions (application classes), design pressuresand pipe dimension classes.

Requirements and test methods for material and components, other than pipes are specifiedin Part 1 and Part 3: MS 1736. Characteristics for fitness for purposes (mainly for joints) arecovered in Part 5 and Part 7 which gives guidance for the assessment of conformity.

This standard and other parts in the series are applicable to PE-X pipes, fittings, their joints and joints with components of PE-X, other plastics and non-plastics materials i Close

RM 30.00

Document will be sent via email



 Add To Cart
PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS – CROSSLINKED POLYETHYLENE (PE-X) : PART 1 : GENERAL (ISO 15875-1:2002, MOD)
MS 1736: PART 1:2004
Status : Original
Format : PDF

This Malaysian Standard specifies the general aspects of crosslinked polyethylene (PE-X) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of ....Read more water, whether or not intended for human consumption (domestic systems), and for heating systems, under design pressures and temperatures according to the class of application (see Table 1).

This standard covers a range of service conditions (application classes) and design pressure classes.

NOTE. It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects,taking into account their particular requirements and any relevant national regulations and installation practices or codes.

Requirements and test methods for components are specified in Parts 2 and 3.Characteristics for fitness of purpose (mainly for joints) are covered in Part 5. Guidance for the assessment of conformity is covered in Part 7.

This standard and other parts in the Close

RM 30.00

Document will be sent via email



 Add To Cart
PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS – CROSSLINKED POLYETHYLENE (PE-X) : PART 3 : FITTINGS (ISO 15875-3:2002, MOD)
MS 1736 : PART 3 : 2004
Status : Original
Format : PDF

This Malaysian Standard specifies the characteristics of fittings for crosslinked polyethylene (PE-X) piping systems intended to be used for hot and cold water installations within buildings for the c ....Read more onveyance of water, whether or not intended for human consumption (domestic systems), and for heating systems, under design pressures and temperatures appropriate to the class of application (see Table 1 of MS 1736: Part 1).

This standard covers a range of service conditions (application classes) and design pressure classes.

NOTE. It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects,taking into account their particular requirements and any relevant national regulations and installation practices or codes.

It also specifies the test parameters for the test methods referred to in this standard.

In conjunction with the other parts of MS 1736, it is applicable to fittings made from crosslinked polyethylene (PE-X) and to fittings m Close

RM 30.00

Document will be sent via email



 Add To Cart
PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CROSSLINKED POLYETHYLENE (PE-X) : PART 7 : GUIDANCE FOR THE ASSESSMENT OF CONFORMITY (ISO/TS 15875-7:2002, MOD)
MS 1736 : PART 7 : 2004
Status : Original
Format : PDF

This Malaysian Standard gives guidance for the assessment of conformity to be included in the manufacturer's quality plan as part of his quality system.

This standard includes:
....Read more r /> a) requirements for materials, components, joints and assemblies given in the applicable part(s) of MS 1736;

b) requirements for the manufacturer’s quality system; and

c) definitions and procedures to be applied if third party certification is involved.

NOTES:

1. It is recommended that the quality system conforms to MS ISO 9001.

2. If third party certification is involved, it is recommended that the certification body is accredited to MS ISO/IEC Guide 65, MS ISO/IEC Guide 62, as applicable.

In conjunction with the other parts of MS 1736, this standard is applicable to crosslinked polyethylene (PE-X) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption(domestic systems), and for heating s Close

RM 30.00

Document will be sent via email



 Add To Cart
PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS – CROSSLINKED POLYETHYLENE (PE-X) : PART 5 : FITNESS FOR PURPOSE OF THE SYSTEM (ISO 15875-5:2002, MOD)
MS 1736 : PART 5 : 2004
Status : Original
Format : PDF

This Malaysian Standard specifies the characteristics of the fitness for purpose of crosslinked polyethylene (PE-X) piping systems, intended to be used for hot and cold water installations within buil ....Read more dings for the conveyance of water whether or not intended for human consumption(domestic systems), and for heating systems, under design pressures and temperatures according to the class of application.

This standard covers a range of service conditions (application classes) and design pressure classes.

NOTE. It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects,taking into account their particular requirements and any relevant national regulations and installation practices or codes.

It also specifies the test parameters for the test methods referred to in this standard.

Requirements and test methods for components of the piping system are specified in Parts 1,2 and 3 of this standard. Part 7 gives guidance for the assessment o Close

RM 15.00

Document will be sent via email



 Add To Cart
PLASTICS – BLOW-MOULDED THERMOPLASTIC CONTAINERS – DETERMINATION OF DROP IMPACT RESISTANCE
MS 1735:2004
Status : Original
Format : PDF

This Malaysian Standard specifies three methods for determining the drop impact resistance of blow-moulded thermoplastic containers as a summation of the effects of material, manufacturing conditions, ....Read more container design, and other factors.

The methods are as follows:

a) Method A, Static drop height;

b) Method B, Bruceton staircase; and

c) Method C, Cumulative mean failure. Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 382
  • 383
  • 384
  • 385
  • 386
  • 387
  • 388
  • ...
  • 587
  • 588
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.