• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Roofing products from metal sheet - Self-supporting products of steel sheet - Specification
MS 2500:2012
Status : Original
Format : PDF

This Malaysian Standard specifies requirements for self-supporting roofing products for discontinuous laying made from metallic coated steel sheet with or without additional organic coatings.
< ....Read more br /> This standard establishes general characteristics, definitions, classifications and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply when purchased before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions.

This standard applies to all discontinuously laid self-supporting external profiled sheets for roofing with the exception of tiles with a surface area less than 1 m2 and produced by stamping. These profiled roof sheets are designed to keep wind and rain out of the building and to Close

RM 75.00

Document will be sent via email



 Add To Cart
Roofing products from metal sheet - Self-supporting products of steel sheet - Specification ERRATA 1
MS 2500:2012, ERR. 1:2013
Status : Errata 1
Format : PDF

This Malaysian Standard specifies requirements for self-supporting roofing products for discontinuous laying made from metallic coated steel sheet with or without additional organic coatings.
....Read more
This standard establishes general characteristics, definitions, classifications and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply when purchased before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions.

This standard applies to all discontinuously laid self-supporting external profiled sheets for roofing with the exception of tiles with a surface area less than 1 m2 and produced by stamping. These profiled roof sheets are designed to keep wind and rain out of the building and to Close

FREE

Document will be sent via email



Please Login to enable MS to be send via email
Eco-labelling criteria for food-grade lubricants
MS 2499:2012
Status : Original
Format : PDF

This Malaysian Standard establishes the criteria for eco-labelling of food-grade lubricants used in lubrication, heat transfer, load transmission or corrosion protection of machines and equipment in t ....Read more he manufacturing and processing of food and products that may include, but not limited to cosmetics, pharmaceuticals, tobacco, animal feed and cleaning agent. This Malaysian Standard does not cover evaluation of product performance or operational criteria for food processing and other facilities. This Malaysian Standard seeks to define good environmental performance benchmarks for food grade lubricants and to promote restriction on highly toxic materials, to reduce the use of hazardous and polluting substances. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



Eco-labelling criteria for adhesives
MS 2498:2012
Status : Original
Format : PDF

This Malaysian Standard establishes environmental requirements for adhesives and water-based adhesives for industrial and consumer application. It is intended to be used for third party certification ....Read more of adhesives and water-based adhesives for the manufacturers to obtain eco-label/environmental preferred recognition. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



Cranes - Bridge and gantry cranes
MS 2496:2012
Status : Original
Format : PDF

This Malaysian Standard specifies the requirements for power-driven overhead travelling cranes for general use.

RM 150.00

Document will be sent via email



 Add To Cart
Pipework - Stainless steel fittings threaded in accordance with MS 1989: Part 1 (ISO 4144:2003, MOD)
MS 2495:2012
Status : Original
Format : PDF

This Malaysian Standard specifies the types, pressure-temperature ratings, minimum dimensions and materials of stainless steel fittings for threaded connections used for ordinary piping for steam, air ....Read more , gas, water, oil, etc. Close

RM 45.00

Document will be sent via email



 Add To Cart
Paper and board - Determination of bending resistance - Part 1: Constant rate of deflection (Second revision) (ISO 2493-1:2010, IDT)
MS ISO 2493-1:2012 (CONFIRMED:2023)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies procedures, based on the two-point loading principle, for determining the bending resistance of paper and board.

NOTE 1: See ISO 5628[1] for a detaile ....Read more d description of the two-point loading principle.

This Malaysian Standard applies to the measurement of the bending resistance within the range 20 mN to 10 000 mN. It is not applicable to corrugated board but can be applicable to the components of such board.

The bending angle is 15° and the bending length is 50 mm.

For samples having a bending resistance that is too low to measure with a bending length of 50 mm, a shorter bending length, i.e. 10 mm, can be used.

IMPORTANT — The results obtained when using different bending lengths will not be comparable.

For boards that tend to be permanently deformed if bent through 15°, the half bending angle, i.e. 7,5°, can be used.

NOTE 2: Taber-type testers and testers using the principle of constant rate of deflection do not give comparable results. F Close

RM 30.00

Document will be sent via email



 Add To Cart
Respiratory protective devices - Half masks and quarter masks - Requirements, testing, marking
MS 2490:2012
Status : Original
Format : PDF

This Malaysian Standard specifies minimum requirements for half masks and quarter masks for use as part of respiratory protective device, except escape and diving apparatus. Laboratory and practical ....Read more performance tests are included for the assessment of compliance with the requirements. Close

RM 30.00

Document will be sent via email



 Add To Cart
Respiratory protective devices - Compressed air line breathing apparatus with demand valve - Part 2: Apparatus with a half mask at positive pressure - Requirements, testing, marking
MS 2489-2:2012
Status : Original
Format : PDF

This Malaysian Standard specifies minimum requirements for compressed air line breathing apparatus with demand valve for use with a half mask at positive pressure as a respiratory protective device. E ....Read more scape and diving apparatus and that used in abrasive blasting operations without additional protective features are not covered by this standard, although certain requirements addressing the use in conjunction with escape apparatus and escape conditions are given. Laboratory and practical performance tests are included for the assessment of conformance to the requirements. Close

RM 45.00

Document will be sent via email



 Add To Cart
Respiratory protective devices - Compressed air line breathing apparatus with demand valve - Part 1: Apparatus with a full face mask - Requirements, testing, marking
MS 2489-1:2012
Status : Original
Format : PDF

This Malaysian Standard specifies minimum requirements for compressed air line breathing apparatus with demand valve for use with a full mask as a respiratory protective device. Escape and diving appa ....Read more ratus and that used in abrasive blasting operations without additional protective features are not covered by this standard, although certain requirements addressing the use in conjunction with escape apparatus and escape conditions are given. Laboratory and practical performance tests are included for the assessment of conformance to the requirements.  Close

RM 60.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • ...
  • 587
  • 588
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.