• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




CONTROL CHARTS – GENERAL GUIDE AND INTRODUCTION (ISO 7870 : 1993 , IDT)
MS ISO 7870 : 2000
Status : Withdrawn
Format : PDF

This International Standard presents key elements and philosophy of the control chart approach, and identifies a wide variety of control charts, including those related to the Shewhart control chart a ....Read more nd those with process acceptance or online predictive emphasis. 
It presents an overview of the basic principles and concepts and illustrates the relationship among various control chart approaches to aid in the selection of the most appropriate standard for given circumstances.

It does not specify statistical control methods using control charts. These methods will be specified in IS0 7873 and IS0 7966, and in other future Inter- national Standards. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



Sterile hypodermic needles for single use (ISO 7864:1993, IDT)
MS ISO 7864:2011
Status : Original
Format : PDF

This Malaysian Standard specifies requirements for sterile hypodermic needles for single use of nominal outside diameters 0.3 mm and 1.2 mm. 
It does not apply to dental needles.

RM 30.00

Document will be sent via email



 Add To Cart
Iron ores - Determination of arsenic content - Molybdenum blue spectrophotometric method (ISO 7834:1987, IDT)
MS ISO 7834:2004 (CONFIRMED:2013)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies a molybdenum blue spectrophotometric method for the determination of the arsenic content of iron ores. 
This method is applicable to a concentration range of 0 ....Read more ,000 1 to 0,l % (mlm) (1 to 1 000 pg/g) of arsenic in natura1 iron ores, and iron ore concentrates and agglomerates including Sinter products. Close

RM 30.00

Document will be sent via email



 Add To Cart
IRON ORES - PREPARATION OF PREDRIED TEST SAMPLES FOR CHEMICAL ANALYSIS (FIRST REVISION) (ISO 7764:2006, IDT)
MS ISO 7764:2011
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies a method for the preparation of predried test samples of natural iron ores, and iron ore concentrates and agglomerates, including sinter products, which are to be use ....Read more d for the determination of analytical values of constituents on a dry basis. 
The method is not applicable to the following types of ores:

a) processed ores containing metallic iron (direct-reduced iron);
b) natural or processed ores in which the mass fraction of sulfur is higher than 0,2 %;
c) natural or processed ores in which the content of combined water is higher than 2,5 % by mass.

NOTE 1 Alternatively, the loss on ignition may be determined as an estimate of the combined water content.

Where this method is not applicable, ISO 2596:1994, Iron ores — Determination of hygroscopic moisture in analytical samples — Gravimetric and Karl Fischer methods is used.

NOTE 2 A laboratory may elect to use ISO 2596 for all samples to determine the dry sample mass. Close

RM 15.00

Document will be sent via email



 Add To Cart
ERGONOMICS - DANGER SIGNALS FOR PUBLIC AND WORK AREAS - AUDITORY DANGER SIGNALS (ISO 7731:2003, IDT)
MS ISO 7731:2007 (CONFIRMED:2023)
Status : 1st Confirmation
Format : PDF

This standard specifies the physical principles of design, ergonomic requirements and the corresponding test methods for danger signals for public and work areas in the signal reception area and gives ....Read more gidelines for the design of the signals. It may also be applied to other appropriate situations. The relevance given in the definitions as to the difference between an auditory emergency signal, auditory emergency evacuation signal and an auditory warning signal should be noted. Close

RM 45.00

Document will be sent via email



 Add To Cart
ERGONOMICS OF THE THERMAL ENVIRONMENT - ANALYTICAL DETERMINATION AND INTERPRETATION OF THERMAL COMFORT USING CALCULATION OF THE PMV AND PPD INDICES AND LOCAL THERMAL COMFORT CRITERIA (ISO 7730:2005, IDT)
MS ISO 7730:2007
Status : Original
Format : PDF

This Malaysian Standard presents methods for predicting the general thermal sensation and degree of discomfort (thermal dissatisfaction) of people exposed to moderate thermal environments. It enables ....Read more the analytical determination and interpretation of thermal comfort using calculation of PMV (predicted mean vote) and PPD (predicted percentage of dissatisfied) and local thermal comfort criteria, giving the environmental conditions considered acceptable for general thermal comfort as well as those representing local discomfort. It is applicable to healthy men and women exposed to indoor environments where thermal comfort is desirable, but where moderate deviations from thermal comfort occur, in the design of new environments or the assessment of existing ones. 
Although developed specifically for the work environment, it is applicable to other kinds of environment as well. It is intended to be used with reference to ISO/TS 14415:2005, 4.2, when considering persons with special requirement Close

RM 90.00

Document will be sent via email



 Add To Cart
Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Acrylonitrile-butadiene-styrene (ABS) (First revision) (ISO 7682:2003, IDT)
MS ISO 7682:2012 (CONFIRMED:2019)
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies the requirements for solid-wall acrylonitrile-butadiene-styrene (ABS) pipes and fittings for soil and waste discharge (low and high temperature) above ground inside b ....Read more uildings, as well as the system itself. It does not include buried pipework. 
It also specifies the test parameters for the test methods referred to in this standard.

This Malaysian Standard is applicable to ABS pipes and fittings, as well as assemblies of such pipes and fittings, intended to be used for the following purposes:
a) soil and waste discharge pipework for the conveyance of domestic waste waters (low and high temperature);
b) ventilation pipework associated with a);
c) rainwater pipework inside the building.

It is applicable to pipes and fittings for jointing by means of elastomeric sealing rings, solvent cementing or integral dual-purpose sockets, i.e. for elastomeric ring seal joints and/or for solvent cement joints.

Two systems, system I and system II, are specified Close

RM 60.00

Document will be sent via email



 Add To Cart
Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Chlorinated poly(vinyl chloride) (PVC-C) (First revision) (ISO 7675:2003, IDT)
MS ISO 7675:2012 (CONFIRMED:2024)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies the requirements for solid-wall chlorinated poly(vinyl chloride (PVC-C) pipes and fittings for soil and waste discharge (low and high temperature) inside buildings, a ....Read more s well as the system itself. It does not include buried pipework. 
It also specifies the test parameters for the test methods referred to in this standard.

This Malaysian Standard is applicable to PVC-C pipes and fittings, as well as assemblies of such pipes and fittings, intended to be used for the following purposes:
a) soil and waste discharge pipework for the conveyance of domestic waste waters (low and high temperature);
b) ventilation pipework associated with a);
c) rainwater pipework inside the building.

It is applicable to pipes and fittings designed for jointing by means of elastomeric sealing rings solvent cementing or integral dual-purpose sockets, i.e. for elastomeric ring seal joints and/or for solvent cement joints. Close

RM 60.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized or thermoplastic - Determination of indentation hardness - Durometer method (Shore hardness) (First revision) (ISO 7619-1:2010, IDT)
MS ISO 7619-1:2013
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies a method for determining the indentation hardness (Shore hardness) of vulcanized or thermoplastic rubber using durometers with the following scales: 
- the A s ....Read more cale for rubbers in the normal-hardness range;
- the D scale for rubbers in the high-hardness range;
- the AO scale for rubbers in the low-hardness range and for cellular rubbers;
- the AM scale for thin rubber test pieces in the normal-hardness range. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



Rubber, vulcanized or thermoplastic - Determination of indentation hardness - IRHD pocket meter method (First revision) (ISO 7619-2:2010, IDT)
MS ISO 7619-2:2013
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies a method for determining the indentation hardness of vulcanized or thermoplastic rubber by means of a pocket hardness meter calibrated in IRHD. The use of such meters ....Read more is primarily intended for control, not specification, purposes. It is possible to increase precision by fixing the pocket hardness meter on a support. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



  • ‹
  • 1
  • 2
  • ...
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • ...
  • 587
  • 588
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.