• :  
BM ENG
  • Subscription
  • MS Catalogue
  • MS Pack
  • Purchase History
  • Cart
  • Hi
    !
    • My Profile
    • Portal
    • Log Out

Modal title

Widget settings form goes here

Search Malaysian Standard (MS)
 Advanced Search Search

GUIDE TO MODULAR COORDINATION IN BUILDINGS : PART 6: COORDINATING SIZED AND PREFERRED SIZES FOR RIGID FLAT SHEETS (FIRST REVISION)
MS 1064: PART 6:2001 (CONFIRMED:2009)
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies coordinating sizes and preferred sizes for rigid flat sheets used in buildings.

RM 15.00

Document will be sent via email



 Add To Cart
PLASTICS PIPING SYSTEMS FOR SOIL, VENTILATION AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE – UNPLASTICISED POLY(VINYL CHLORIDE) (PVC-U) – SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM (FIRST REVISION)
MS 1063 : 2002
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies the requirements for pipes, fittings and the system of unplasticised poly(vinyl chloride) (PVC-U) piping systems in the field of soil, ventilation and waste discharge ....Read more (low and high temperature) inside buildings (marked with “B”), for soil and waste discharge systems buried in ground within the building structure (marked with “D”) and for soil, ventilation and waste discharge for both inside buildings and buried in building structures (marked with “BD”).

It also specifies the test parameters for the test method referred to in this standard.

This Malaysian Standard covers a range of pipes and fittings sizes.

NOTE. It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. Close

RM 75.00

Document will be sent via email



 Add To Cart
PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - UNPLASTICIZED POLY(VINYL CHLORIDE )(PVC-U) - SPECIFICATION FOR PIPES, FITTINGS AND THE SYSTEM (FIRST REVISION)
MS 1063:2002, AMD. 1:2010
Status : Amendment 1
Format : PDF

This Malaysian Standard specifies the requirements for pipes, fittings and the system of unplasticised poly(vinyl chloride) (PVC-U) piping systems in the field of soil, ventilation and waste discharge ....Read more (low and high temperature) inside buildings (marked with “B”), for soil and waste discharge systems buried in ground within the building structure (marked with “D”) andfor soil, ventilation and waste discharge for both inside buildings and buried in building structures (marked with “BD”). Close

FREE

Document will be sent via email



 Send To Email
SPECIFICATION FOR BORED LOCKS AND LATCHES FOR BUILDINGS
MS 1062 : 1986
Status : Original
Format : PDF

This Malaysian Standard specifies tests and levels of performance for bored locks and latches for doors in buildings.

RM 30.00

Document will be sent via email



 Add To Cart
VITRIFIED CLAY PIPES AND FITTINGS AND PIPE JOINTS FOR DRAINS AND SEWERS PART 3 : TEST METHODS (FIRST REVISION)
MS 1061: PART 3:1999 (CONFIRMED:2008)
Status : Withdrawal with replacement
Format : PDF

This Malaysian Standard is the specification for the methods of test for requirements of MS 1061 : Part 1.

NOTE. Where reference is made to clauses in MS 1061: Part 1, it is clearly sta ....Read more ted.

Throughout the clauses in this standard reference to pipes includes pipe sections as defined in clause 3.8 of MS 1061: Part I, where these are suitable and permitted for the tests. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



VITRIFIED CLAY PIPES AND FITTINGS AND PIPE JOINTS FOR DRAINS AND SEWERS PART 2 : QUALITY CONTROL AND SAMPLING (FIRST REVISION)
MS 1061: PART 2:1999 (CONFIRMED:2008)
Status : Withdrawal with replacement
Format : PDF

This Malaysian Standard specifies requirements for manufacturer’s internal quality control, third party assessment and inspection.

NOTE. Where reference is made to clauses in MS 1061 ....Read more : Part I and MS 1061 : Part 3 it is clearly stated. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



VITRIFIED CLAY PIPES AND FITTINGS AND PIPE JOINTS FOR DRAINS AND SEWERS : PART 1 : REQUIREMENTS (FIRST REVISION)
MS 1061: PART 1:1999 (CONFIRMED:2008)
Status : Withdrawal with replacement
Format : PDF

This Malaysian Standard specifies requirements for flexibly jointed vitrified claypipes and fittings with or without sockets for the construction of drainage and sewerage systems. Although normally op ....Read more erated under gravity, the pipes and fittings covered by this standard will accept periodic hydraulic surcharge.

If pipes are required to withstand continuous working under low pressure, the pressure used in tests in this standard shall be agreed between the manufacturer and the purchaser with a maximum test pressure of 600 kPa (6.0 bar).

The preferred dimensions for pipe lengths, curvature of bends and angles of junction arms are specified in this standard. Other values for these dimensions are acceptable providing the products meet all the relevant performance requirements and are marked correctly.

Fittings groups covered by this part of this standard are given in MSIO6I: Part 2.

Where this standard provides for different strength classes, different systems of jointing dimensions, dif Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



SPECIFICATION FOR MORTICE LOCKS FOR USE IN BUILDINGS
MS 1060 : 1986
Status : Original
Format : PDF

This Malaysian Standard specifies tests and levels or performance of upright mortice locks and, bathroom locks or doors used in buildings.

RM 30.00

Document will be sent via email



 Add To Cart
POLYETHYLENE (PE) PIPING SYSTEMS FOR WATER SUPPLY – PART 1: GENERAL (FOURTH REVISION)
MS 1058: PART 1:2005
Status : 3rd Revision
Format : PDF

This Malaysian Standard specifies the general aspects of polyethylene (PE) piping systems (mains and service pipes) intended for the conveyance of water for human consumption, including raw water prio ....Read more r to treatment

It also specifies the test parameters for the test methods referred to in this Malaysian Standard.

In conjunction with other parts of this standard (see Foreword), it is applicable to PE pipes,
their joints and to joints with components of PE and other materials intended to be used under
the following conditions:

a) a maximum operating pressure, MOP, up to 25 bar1); and

b) an operating temperature of 20 °C as a reference temperature.

NOTE. For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see Annex B.

MS 1058 covers a range of maximum operating pressures and gives requirements
concerning colours and additives. Close

RM 30.00

Document will be sent via email



 Add To Cart
POLYETHYLENE (PE) PIPING SYSTEMS FOR WATER SUPPLY – PART 4: FITNESS FOR PURPOSE OF THE SYSTEM
MS 1058: PART 4:2006
Status : Original
Format : PDF

This Malaysian Standard specifies the characteristics of the fitness for purpose of the assembled piping systems intended for the conveyance of water intended for human consumption, including raw wate ....Read more r prior to treatment.

It also specifies the test parameters for the test methods referred to in this standard.

In conjunction with other parts of this standard (see Foreword) it is applicable to PE pipes, fittings, their joints and to joints with components of other materials intended to be used under
the following conditions:

a) a maximum operating pressure, MOP, up to 25 bar 1); and

b) an operating temperature of 20 °C as a reference temperature. Close

RM 15.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 451
  • 452
  • 453
  • 454
  • 455
  • 456
  • 457
  • ...
  • 580
  • 581
  • ›