• :  
BM ENG
  • Subscription
  • MS Catalogue
  • MS Pack
  • Purchase History
  • Cart
  • Hi
    !
    • My Profile
    • Portal
    • Log Out

Modal title

Widget settings form goes here

Search Malaysian Standard (MS)
 Advanced Search Search

BOXES AND ENCLOSURES FOR ELECTRICAL ACCESSORIES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS - PART 21: PARTICULAR REQUIREMENTS FOR BOXES AND ENCLOSURES WITH PROVISION FOR SUSPENSION MEANS (FIRST REVISION) (IEC 60670-21:2004, IDT)
MS 1873-21:2006
Status : 1st Revision
Format : PDF

The scope of Part 1 of this Malaysian Standard is applicable with the following modification:

Addition after the fourth paragraph:

This standard applies to boxes and enclosur ....Read more es with provision for suspension means. Close

RM 30.00

Document will be sent via email



 Add To Cart
PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (FIRST REVISION) (ISO 1873-2:2007, IDT)
MS ISO 1873-2:2010
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of PP moulding and extrusion materials. Requirements for ha ....Read more ndling test material and for conditioning both the test material before moulding and the specimens before testing are given.

Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are given. Properties and test methods which are suitable and necessary to characterize PP moulding and extrusion materials are listed.

The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for, or of particular significance to, these moulding and extrusion materials are also included in this part of ISO 1873, as are the designatory properties specified in Part 1. Close

RM 30.00

Document will be sent via email



 Add To Cart
BOXES AND ENCLOSURES FOR ELECTRICAL ACCESSORIES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS - PART 24: PARTICULAR REQUIREMENTS FOR ENCLOSURES FOR HOUSING PROTECTIVE DEVICES AND SIMILAR POWER CONSUMING DEVICES (FIRST REVISION) (IEC 60670-24:2005, IDT)
MS 1873: PART 24:2007
Status : 1st Revision
Format : PDF

This Malaysian Standard applies to empty enclosures and parts of them for electrical accessories intended to be used with a rated voltage not exceeding 400 V and a total incoming load current not exce ....Read more eding 125 A for household and similar fixed electrical installations, where a maximum capability to dissipate power in normal use is declared by the manufacturer.

These enclosures are intended for housing protective devices and devices with or without power dissipation. They are intended to be installed where the prospective short circuit current does not exceed 10 kA unless they are protected by current limiting protective devices with a cut-off current not exceeding 17 kA.

Enclosures complying with this standard are suitable for use, after installation, at ambient temperature normally not exceeding 25 °C, but occasionally reaching 35 °C over 24 h, max. 40 °C and min. –5 °C. An enclosure which is an integral part of an electrical accessory and provides protection against external influe Close

RM 45.00

Document will be sent via email



 Add To Cart
BOXES AND ENCLOSURES FOR ELECTRICAL ACCESSORIES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS - PART 22: PARTICULAR REQUIREMENTS FOR CONNECTING BOXES AND ENCLOSURES (FIRST REVISION) (IEC 60670-22:2004, IDT)
MS 1873:2005
Status : 1st Revision
Format : PDF

This Malaysian Standards applies to boxes, enclosures and parts of enclosures (here after called “boxes” and “enclosures”) for electrical accessories with a rated voltage not exceeding 1 000 V ....Read more a.c. and 1 500 V d.c. intended for household or similar fixed electrical installations, either indoors or outdoors.

NOTE. Requirements for particular types of boxes and enclosures are given in the relevant parts 2 of IEC 60670.

Boxes and enclosures complying with this standard are suitable for use at ambient tem-perature not normally exceeding 25 °C but occasionally reaching 35 °C.

This Malaysian Standard is intended to apply to boxes and enclosures for electrical accessories within the scope of IEC technical committee 23.

A box or an enclosure which is an integral part of an electrical accessory and provides protection for that accessory against external influences (for example mechanical impact, ingress of solid objects or water, etc.) is covered by the relevant standard for such anaccessor Close

RM 105.00

Document will be sent via email



 Add To Cart
BOXES AND ENCLOSURES FOR ELECTRICAL ACCESSORIES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS - PART 22: PARTICULAR REQUIREMENTS FOR CONNECTING BOXES AND ENCLOSURES (FIRST REVISION) (IEC 60670-22:2004, IDT)
MS 1873: PART 22:2006
Status : 1st Revision
Format : PDF

The scope of Part 1 of this Malaysian Standard applies with the following addition:

Add after the fourth paragraph:

This standard applies to connecting boxes for junction(s) ....Read more and/or tapping(s).

NOTE. Unless otherwise stated, throughout the document the term “boxes” also applies to “enclosures”. Close

RM 30.00

Document will be sent via email



 Add To Cart
Flexible cellular polymeric materials - Determination of compression set under humid conditions (ISO 13362:2000, MOD)
MS 1872:2005 (CONFIRMED:2013)
Status : Original
Format : PDF

This Malaysian Standard specifies a method for determining the compression set of flexible cellular materials under humid conditions.

This method consists of maintaining the test piece un ....Read more der specified conditions of time, temperature, humidity and constant compressive strain and determining the effect on the thickness of the test piece after a specified recovery period. Close

RM 15.00

Document will be sent via email



 Add To Cart
PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 1872-2:2007, IDT)
MS ISO 1872-2:2008
Status : Original
Format : PDF

This Malaysian Standard specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of polyethylene (PE) moulding and extrusion materials. Requ ....Read more irements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given.

Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are also given. Properties and test methods that are suitable and necessary to characterize PE moulding and extrusion materials are listed.

The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for or of particular significance to these moulding and extrusion materials are also included in this part of ISO 1872, as are the designatory properties specified in ISO 1872-1. Close

RM 30.00

Document will be sent via email



 Add To Cart
FLEXIBLE CELLULAR POLYMERIC MATERIALS – DETERMINATION OF COMPRESSION SET UNDER HUMID CONDITIONS (ISO 13362:2000, MOD)
MS 1872:2005 (Confirmed:2020)
Status : 2nd Confirmation
Format : PDF

This Malaysian Standard specifies a method for determining the compression set of flexible cellular materials under humid conditions.

This method consists of maintaining the test piece un ....Read more der specified conditions of time, temperature, humidity and constant compressive strain and determining the effect on the thickness of the test piece after a specified recovery period. Close

RM 15.00

Document will be sent via email



 Add To Cart
FLEXIBLE CELLULAR POLYMERIC MATERIALS - DETERMINATION OF COMPRESSION SET (ISO 1856:2000, MOD)
MS 1871:2005
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies three methods for determining the compression set of flexible cellular materials.

At present, this International Standard applies only to latex and polyu ....Read more rethane foams of thickness greater than2 mm. Met hods for other materials will be added as required. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



Gas meters - Diaphragm gas meters
MS 1870:2005
Status : Original
Format : PDF

This Malaysian Standard is identical with EN 1359:1998, Gas meters – Diaphragm gas meters, published by the European Committee for Standardization (CEN) with the exceptions as listed below.
....Read more
This standard is published with the permission of the European Committee for Standardization. Such permission is hereby acknowledged. Close

RM 75.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 352
  • 353
  • 354
  • 355
  • 356
  • 357
  • 358
  • ...
  • 580
  • 581
  • ›