• :  
BM ENG
  • Subscription
  • MS Catalogue
  • MS Pack
  • Purchase History
  • Cart
  • Hi
    !
    • My Profile
    • Portal
    • Log Out

Modal title

Widget settings form goes here

Search Malaysian Standard (MS)
 Advanced Search Search

RUBBER AND PLASTICS HOSES - ASSESSMENT OF OZONE RESISTANCE UNDER STATIC CONDITIONS (ISO 7326:2006, IDT)
MS ISO 7326:2007
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies five methods for determining the ozone resistance of the outer covers of hoses: 
-method 1, for bore sizes up to and including 25 mm, carried out on the hose ....Read more itself;
-method 2, for bore sizes greater than 25 mm, carried out on a test piece from the hose wall;
-method 3, for bore sizes greater than 25 mm, carried out on a test piece from the cover;
-method 4, for all bore sizes, carried out on the hose itself;
-method 5, for all bore sizes, carried out on hoses that are expandable, for example textile-reinforced hoses.

NOTE. For hoses with built-in fittings from which it is not possible to take test pieces, the ozone resistance may be assessed on slabs in accordance with ISO 1431-1, using test sheets of the appropriate polymeric compound vulcanized to the same degree. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



Corrugating medium - Determination of the flat crush resistance after laboratory fluting (First revision) (ISO 7263:2011, IDT)
MS ISO 7263:2012
Status : Original
Format : PDF

This Malaysian Standard specifies two methods for the determination of the flat crush resistance of a corrugating medium after laboratory fluting. 
The procedures are applicable to any corrugat ....Read more ing medium intended to be used, after fluting, in the
manufacture of corrugated board. Close

RM 30.00

Document will be sent via email



 Add To Cart
Basic human body measurements for technological design - Part 1: Body measurement definitions and landmarks (First revision) (ISO 7250-1:2008, IDT)
MS ISO 7250-1:2008 (CONFIRMED:2013)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard provides a description of anthropometric measurements which can be used as a basis for comparison of population groups. 
The basic list specified in this part of ISO 725 ....Read more 0 is intended to serve as a guide for ergonomists who are required to define population groups and apply their knowledge to the geometric design of the places where people work and live.

This list is not intended to serve as a guide for how to take anthropometric measurements, but it gives information to the ergonomist and designer on the anatomical and anthropometrical bases and principles of measurement which are applied in the solution of design tasks.

This Malaysian Standard is intended to be used in conjunction with national or international regulations or agreements to assure harmony in defining population groups. In its various applications, it is anticipated that the basic list will be supplemented by specific additional measurements. Close

RM 60.00

Document will be sent via email



 Add To Cart
BASIC HUMAN BODY MEASUREMENTS FOR TECHNOLOGICAL DESIGN(ISO 7250:1996, IDT)
MS ISO 7250:2003
Status : Original
Format : PDF

This Malaysian Standard provides a description of anthropometric measurements which can be used as a basis for comparison of population groups. 
The basic list specified in this standard is int ....Read more ended to serve as a guide for ergonomists who are required to define population groups and apply their knowledge to the geometric design of the places where people work and live.

This list is not intended to serve as a guide for how to take anthropometric measurements, but it gives in- formation to the ergonomist and designer on the anatomical and anthropometrical bases and principles of measurement which are applied in the solution of design tasks.

This Malaysian Standard may be used in conjunction with national or international regulations or agreements to assure harmony in defining population groups. In its various applications, it is anticipated that the basic list will be supplemented by specific additional measurements. Close

RM 45.00

Document will be sent via email



 Add To Cart
Rubber and plastics hoses and hose assemblies - Determination of resistance to vacuum (ISO 7233:2006, IDT)
MS ISO 7233:2008 (CONFIRMED:2013)
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies three methods for determining the resistance to vacuum of hoses and hose assemblies manufactured from plastic or rubber. 
Applicable dimensions of hoses for e ....Read more ach method are as follows:
- method A — for hoses of nominal bore up to and including 80 mm;
- method B — for hoses of nominal bore greater than 80 mm;
- method C — for hoses of all dimensions.

Methods A and B can also be used to check the adhesion of the lining to the reinforcement (delamination) in a length of hard-wall hose or hose assembly. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



GAS CYLINDERS – PRECAUTIONARY LABELS (ISO 7225:2005, IDT)
MS ISO 7225:2006
Status : Original
Format : PDF

This Malaysian Standard specifies the design, content (i.e. hazard symbols and text) and application of precautionary labels intended for use on individual gas cylinders containing single gases or gas ....Read more mixtures. Labels for cylinders of bundles and labels for bundles are not covered by this Malaysian Standard. Close

RM 30.00

Document will be sent via email



 Add To Cart
PULPS – SAMPLING FOR TESTING (ISO 7213 - 1981, IDT)
MS ISO 7213 : 2001
Status : Original
Format : PDF

This Malaysian Standard specifies a method of obtaining, for test purposes, a gross sample representative of a certain lot of pulp. This Malaysian Standard applies to all kinds of pulp delivered in ba ....Read more les or rolls. lt is recommended for use when sampling for all kinds of testing purposes except for the determination of saleable mass, in which case other International Standards should be applied, such as ISO 801/1 or ISO 801/2. 
If, however, the pulp is to be tested for saleable mass in addition to other properties, the gross sample obtained according to the appropriate standard for sampling saleable mass may also be used for the other pulp property tests. Close

RM 15.00

Document will be sent via email



 Add To Cart
TEXTILES – WOVEN FABRICS – CONSTRUCTION – METHODS OF ANALYSIS – PART 2: DETERMINATION OF NUMBER OF THREADS PER UNIT LENGTH (ISO 7211-2:1984, IDT)
MS ISO 7211-2:2003 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies three methods for the determination of the number of threads per centimetre in woven fabrics.

RM 15.00

Document will be sent via email



 Add To Cart
Implants for surgery - Components for partial and total knee joint prostheses - Part 1: Classification, definitions and designation of dimensions (ISO 7207-1:2007, IDT)
MS ISO 7207-1:2010 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard classifies femoral, tibial and patellar components for knee joint prostheses in which the bearing surfaces of one or more compartments of the knee are replaced. It also gives d ....Read more efinitions of components and the designation of dimensions. Close

RM 30.00

Document will be sent via email



 Add To Cart
Wheelchairs - Part 19: Wheeled mobility devices for use as seats in motor vehicles (ISO 7176-19:2008, IDT)
MS ISO 7176-19:2010 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard applies to all manual and powered wheelchairs, including scooters, which, in addition to their primary function as wheeled mobility devices, are also likely to be used as forwa ....Read more rd-facing seats in motor vehicles by children and adults with a body mass equal to or greater than 22 kg. This standard specifies wheelchair design requirements, performance requirements and associated test methods, and requirements for wheelchair labelling, presale literature, user instructions and user warnings. It applies to complete wheelchairs, including a base frame and seating system, as well as to wheelchairs equipped with add-on adaptive components designed to facilitate compliance with one or more of the requirements. Close

RM 75.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • ...
  • 580
  • 581
  • ›