• :  
BM ENG
  • Subscription
  • MS Catalogue
  • MS Pack
  • Purchase History
  • Cart
  • Hi
    !
    • My Profile
    • Portal
    • Log Out

Modal title

Widget settings form goes here

Search Malaysian Standard (MS)
 Advanced Search Search

Household insecticide products - Mosquito Coil - Chemical, physical and biological efficacy requirements (Fifth revision)
MS 23:2017
Status : Original
Format : PDF

This malaysian Standard specifies the minimum chemical and physical requirements, and biological efficacy of mosquito coil products intended for househo ....Read more ld use against mosquitoes.
NOTE. Attention is drawn to the mandatory requirement that mosquito coils marketed in the country is to be registered with the Pesticides Board under the Pesticides Act 1974 (Amendment 2004). Close

RM 30.00

Document will be sent via email



 Add To Cart
PLASTICS PIPING SYSTEMS - INJECTION- MOULDED THERMOPLASTICS FITTINGS FOR ELASTIC SEALING RING TYPE JOINTS FOR PRESSURE PIPING - TEST METHOD FOR RESISTANCE TO A SHORT-TERM INTERNAL PRESSURE WITHOUT END THRUST
MS 2251:2009 (CONFIRMED:2018)
Status : 1st Confirmation
Format : PDF

The adoption of the EN Standard as a malaysian Standard was recommended by the
Technical Committee on Plastics Pipes and Fittings under the author ....Read more ity of the Industry
Standards Committee on Plastics and Plastics Products.
This malaysian Standard is identical with EN 803:1994, Plastics piping systems - Injection moulded
thermoplastics fittings for elastic sealing ring type joints for pressure piping - Test
method for resistance to a short-term internal pressure without end thrust, published by the
European Committee for Standardization (CEN) with the exceptions as listed below.

malaysiaN STANDARD EXCEPTIONS
a) in the source text, "this European Standard" should read "this malaysian Standard"; and
b) the comma which is used as a decimal sign (if any), to read as a point.
This standard is published with the permission of the European Committee for
Standardization. Such permission is hereby acknowledged.
Compliance with a malaysian Standard does not of itself confer immunity from legal
obligations. Close

RM 15.00

Document will be sent via email



 Add To Cart
MOULDED THERMOPLASTICS DUSTBINS (EXCLUDING LIDS) - SPECIFICATION
MS 1906:2006 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This malaysian Standard specifies requirements for the dimensions, materials, design and
performance of moulded dustbins (excluding lids) manufact ....Read more ured from thermoplastics materials
having capacities from 50 L to 120 L.
This malaysian Standard does not take account of:
a) whether the dustbin is to be used in conjunction with a bin liner;
b) the special design requirements necessary if the dustbin is to be subjected to regular
dragging or rolling as part of a collection system. Close

RM 30.00

Document will be sent via email



 Add To Cart
PLASTICS PIPING SYSTEMS - MECHANICAL JOINTS BETWEEN FITTINGS AND POLYOLEFIN PRESSURE PIPES - TEST METHOD FOR LEAKTIGHTNESS UNDER INTERNAL PRESSURE OF ASSEMBLIES SUBJECTED TO BENDING
MS 1741:2004 (CONFIRMED:2018)
Status : 1st Confirmation
Format : PDF

This malaysian Standard specifies a method for checking the leaktightness under internal
hydrostatic pressure of assembled mechanical joints (excl ....Read more uding fusion-welded joints) between
fittings and polyolefin pressure pipes while subjected to bending. It defines a calculation
method for the average bending radius and the procedure for achieving this bending (see
note). Checking of the leaktightness under internal pressure is carried out in accordance with
the method given in EN 715. The test method is applicable regardless of the design and
material of the fitting used for jointing pipes. Close

RM 15.00

Document will be sent via email



 Add To Cart
THERMOPLASTICS PIPING SYSTEMS – END- LOAD BEARING MECHANICAL JOINTS BETWEEN PRESSURE PIPES AND FITTINGS – TEST METHOD FOR RESISTANCE TO PULL OUT UNDER CONSTANT LONGITUDINAL FORCE
MS 1740:2004 (CONFIRMED:2018)
Status : 1st Confirmation
Format : PDF

This malaysian Standard specifies a method for checking the ability of assembled end-load bearing mechanical joints (excluding fusion-welded joints) bet ....Read more ween fittings and pressure pipes to withstand a longitudinal tensile force. Close

RM 15.00

Document will be sent via email



 Add To Cart
PLASTICS PIPING SYSTEMS – THERMOPLASTICS PIPES AND FITTINGS FOR HOT AND COLD WATER – TEST METHOD FOR THE RESISTANCE OF MOUNTED ASSEMBLIES TO TEMPERATURE CYCLING
MS 1739:2004 (CONFIRMED:2018)
Status : 1st Confirmation
Format : PDF

This malaysian Standard specifies a method for testing the resistance to temperature cycling
of joints for piping systems with rigid or flexible t ....Read more hermoplastics pipes.
It is applicable to thermoplastics piping systems intended to be used in hot and cold water pressure applications. Close

RM 15.00

Document will be sent via email



 Add To Cart
PLASTICS PIPING SYSTEMS – INJECTION- MOULDED THERMOPLASTICS FITTINGS, VALVES AND ANCILLARY EQUIPMENT – DETERMINATION OF THE LONG-TERM HYDROSTATIC STRENGTH OF THERMOPLASTICS MATERIALS FOR INJECTION MOULDING OF PIPING COMPONENTS
MS 1738:2004 (CONFIRMED:2018)
Status : 1st Confirmation
Format : PDF

This malaysian Standard specifies methods for preparing tubular test pieces for testing
thermoplastics materials used for injection moulding, to e ....Read more valuate the long-term resistance to
constant internal water pressure at constant temperature and to check the hydrostatic
strength of the material. Close

RM 15.00

Document will be sent via email



 Add To Cart
PLASTICS - BLOW-MOULDED THERMOPLASTIC CONTAINERS - DETERMINATION OF DROP IMPACT RESISTANCE (First revision)
MS 1735:2018
Status : 1st Revision
Format : PDF

This malaysian Standard specifies three methods for determining the drop impact
resistance of blow-moulded thermoplastic containers as a summation ....Read more of the effects of material, manufacturing conditions, container design, and other factors. Close

RM 30.00

Document will be sent via email



 Add To Cart
Guidelines on packaging in plastics containers AMENDMENT 1
MS 1733:2004, AMD. 1:2016
Status : Amendment 1
Format : PDF

AMENDMENT OF malaysiaN STANDARD
malaysiaN STANDARD
MS 1733:2004

FREE

Document will be sent via email



 Send To Email
PLASTICS - BLOW MOULDED THERMOPLASTIC CONTAINERS - PLASTICS LABORATORY WARE - WASH BOTTLES - GENERAL REQUIREMENTS
MS 1503:2018
Status : 1st Revision
Format : PDF

This malaysian Standard specifies details of flexible (squeeze type) plastics wash bottles for general laboratory use.

RM 15.00

Document will be sent via email

For sale within Malaysia Only

 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 514
  • 515
  • 516
  • 517
  • 518
  • 519
  • 520
  • ...
  • 523
  • 524
  • ›