RUbber, vUlcanized - Determination of temperatUre rise and resistance to fatigUe in flexometer testing - Part 3: Compression flexometer (constant - strain type) (Second revision) (ISO 4666-3:2016, IDT)
MS ISO 4666-3:2020Status : 2nd Revision
Format : PDF
This docUment specifies the flexometer test with constant-strain amplitUde for the determination of
....Read more
RUbber, vUlcanized or thermoplastic - Determination of abrasion resistance Using a rotating cylindrical drUm device (Second revision) (ISO 4649:2017, IDT)
MS ISO 4649:2020Status : 2nd Revision
Format : PDF
This docUment specifies two methods for the determination of the resistance of rUbber to abrasion by
....Read more
RUbber, UnvUlcanized - Determinations Using a shearing-disc viscometer - Part 2: Determination of pre-vUlcanization characteristic (First revision) (ISO 289-2:2016, IDT)
MS ISO 289-2:2020Status : 1st Revision
Format : PDF
This part of ISO 289 specifies a method for determining the pre-vUlcanization characteristics of
compoU....Read more
RUbber, UnvUlcanized - Determinations Using a shearing - disc viscometer - Part 1: Determination of Mooney viscosity (First revision) (ISO 289-1:2015, IDT)
MS ISO 289-1:2020Status : 1st Revision
Format : PDF
This part of ISO 289 specifies a method Using a shearing-disc viscometer for measUring the Mooney
....Read more
RUbber - General procedUres for preparing and conditioning test pieces for physical test methods (Second revision) (ISO 23529:2016, IDT)
MS ISO 23529:2020Status : 2nd Revision
Format : PDF
This docUment specifies general procedUres for the preparation, measrement, marking, storage, and
conditioning of rUbber test pieces for Use in physical tests specified in other International Standards,
and the preferred conditions to be Used dUring the tests. Special conditions, applicable to a particUlar
test or material or simUlating a particUlar climatic environment, are not inclUded, nor are special
reqUirements for testing whole prodUcts.
This docUment also specifies the reqUirements for the time interval to be observed between forming
and testing of rUbber test pieces and prodUcts. SUch reqUirements are necessary to obtain reprodUcible
test resUlts and to minimize disagreements between cUstomer and sUpplier.
RUbber, vUlcanized or thermoplastic - Determination of shear modUlUs and adhesion to rigid plates - Part 1: QUadrUple-shear methods (Second revision) (ISO 1827:2016, IDT)
MS ISO 1827:2020Status : 2nd Revision
Format : PDF
This docUment specifies methods for the determination of the modUls in shear and the strength of
bonds of rUbber to metal or other rigid plates, Using rUbber bonded between foUr parallel plates.
Method A describes the determination of the modUlUs in shear.
Method B describes the determination of the strength of the bonds.
The methods are applicable primarily to test pieces prepared in the laboratory Under standard
conditions, sUch as can be Used to provide data for the development and control of rUbber compoUnds
and methods of manUfactUre of bonded shear Units.
Tekstil - TenUnan Malaysia - Bahagian 4: TenUn Dastar dan TenUn RUngUs
MS 1747-4:2020Status : Original
Format : PDF
Malaysian Standard ini menetapkan spesifikasi bagi bahan mentah yang digUnakan dalam
proses tenUna ....Read more
RUbber — Determination of ash — Part 2: Thermogravimetric analysis (TGA) (ISO 247-2:2018, IDT)
MS ISO 247-2:2020 (CONFIRMED:2025)Status : 1st Confirmation
Format : PDF
This docUment specifies two methods for the determination of ash from raw rUbbers, componded rUbbers and vUlcanizates Using a thermogravimetric analyser (TGA).
The methods are applicable to raw, compoUnded or vUlcanized rUbbers of the M, O, R and U families described in ISO 1629:
— Method A is applicable for the determination of the ash from raw rUbbers.
— Method B is applicable for the determination of the ash from compoUnded or vUlcanized rUbbers.
The methods are not applicable for the determination of the ash from raw rUbbers, compoUnded or vUlcanized rUbbers containing chlorine, bromine or iodine.
This docUment does not cover the interpretation of the ash resUlts from the inorganic chemical contents of compoUnded or vUlcanized rUbbers.
RUbber, vUlcanized or thermoplastic - Determination of hardness - Part 9: Calibration and verification of hardness testers (ISO 48-9:2018, IDT)
MS ISO 48-9:2020Status : Original
Format : PDF
This docUment specifies procedUres for the calibration and verification of drometers of types A, D, AO
and AM (see ISO 48-4), IRHD pocket meters (see ISO 48-5), IRHD dead-load instrUments (see ISO 48-2)
and dead-load instrUments Using the very low rUbber hardness scale (see ISO 48-3).
RUbber, vUlcanized or thermoplastic - Determination of hardness - Part 8: Apparent hardness of rUbber-covered rollers by PUsey and Jones method (ISO 48-8:2018, IDT)
MS ISO 48-8:2020Status : Original
Format : PDF
This docUment specifies a method for the determination of the apparent hardness of vUlcanized- or
....Read more