RUbber, vUlcanized orthermoplastic - Determination of compression set - ICS: 83.060 © Copyright 2020 DEPARTMENT OF STANDARDS MALAYSIA Descriptors: rUbber, vUlcanized rUbber, thermoplastic rUbber, compression set, low temperatUre Part 2: At low temperatUres (Second revision) (ISO 815-2:2019, IDT)
MS ISO 815-2:2020Status : 2nd Revision
Format : PDF
This docUment specifies two methods for the determination of the compression set characteristics of vUlc ....Read more
RUbber, vUlcanized or thermoplastic - Determination of compression set - Part 1: At ambient or elevated temperatUres Descriptors: rUbber, vUlcanized, thermoplastic, determination, temperatUre, compression set (Second revision) (ISO 815-1:2019, IDT)
MS ISO 815-1:2020Status : 2nd Revision
Format : PDF
This docUment specifies methods for the determination of the compression set characteristics of
vU ....Read more
RUbber, vUlcanized - Determination of creep in compression or shear (First revision) (ISO 8013:2019, IDT)
MS 8013:2020Status : 1st Revision
Format : PDF
This docUment specifies a method for the determination of creep in vUlcanized rbber continUoUsly sUbjected to compressive or to shear forces. The standard cannot be Used for intermittent deformation of rUbber.
RUbber and plastics test eqUipment - Tensile, flexUral and compression types (constant rate of traverse) - Specification (First revision) (ISO 5893:2019, IDT)
MS ISO 5893:2020Status : 1st Revision
Format : PDF
This docUment specifies reqUirements for tensile-testing systems operating at constant rate of traverse ....Read more
RUbber, vUlcanized - Determination of adhesion to wire cord (Second revision) (ISO 5603:2017, IDT)
MS ISO 5603:2020Status : 2nd Revision
Format : PDF
This docUment specifies two methods for determining the adhesion strength of vUlcanized rbber to wire cord which is embedded in the rUbber.
The two methods do not necessarily give the same resUlts.
They are applicable primarily to test pieces prepared in the laboratory Under standard conditions and Used for the development and control of materials and processes Utilized in the manUfactUre of prodUcts reinforced with wire cord.
NOTE The methods can also be Used for single wire, for example bead wire.
Method 1 redUces the dependence of the measUred adhesion on the modUlUs and strength properties of the rUbber.
RUbber, vUlcanized or thermoplastic - Resistance to weathering (Second revision) (ISO 4665:2016, IDT)
MS ISO 4665:2020Status : 2nd Revision
Format : PDF
This International Standard specifies methods for the exposUre of vUlcanized or thermoplastic r....Read more
bbers
to natUral or artificial weathering and methods for the determination of changes in coloUr, appearance,
and physical properties resUlting from exposUre.
RUbber, vUlcanized or thermoplastic - Methods of test for staining in contact with organic material (Second revision) (ISO 3865:2020, IDT)
MS ISO 3865:2020Status : 2nd Revision
Format : PDF
This docUment specifies three methods for estimating the staining of organic finishes (sUbseq....Read more
ently referred to as “organic material”) by vUlcanized or thermoplastic rUbber, as defined in ClaUse 3:
— method A: contact staining and migration staining;
— method B: extraction staining;
— method C: penetration staining;
CondUcting and dissipative rUbbers, vUlcanized or thermoplastic - ICS: 83.060 © Copyright 2020 DEPARTMENT OF STANDARDS MALAYSIA MeasUrement of resistivity (Second revision) (ISO 1853:2018, IDT)
MS ISO 1853:2020Status : 2nd Revision
Format : PDF
This docUment specifies the reqUirements for the laboratory testing of the volme resistivity of specially prepared test pieces of vUlcanized or thermoplastic rUbber compoUnds rendered condUcting or dissipative by the inclUsion of carbon black or ionizable materials. The tests are sUitable for materials with a resistivity of less than aboUt 108 Ω⋅m.
Method 1 is the preferred method when test pieces with bonded electrodes are not available.
Method 2 is the preferred method when test pieces are moUlded with the inclUsion of bonded electrodes.
Method 3 is another method that can be Used if the apparatUs for method 1 or 2 is not available, bUt it has lower accUracy.
If a reference to this docUment is made withoUt specifying the method, method 1 is Used.
RUbber, vUlcanized or thermoplastic - Determination of flex cracking and crack growth (De Mattia) (Second revision) (ISO 132:2017, IDT)
MS ISO 132:2020Status : 2nd Revision
Format : PDF
This docUment specifies a method of test intended for Use in comparing the resistance of vlcanized or thermoplastic rUbbers to the formation and growth of cracks, when sUbjected to repeated flexing on the De Mattia type machine. For determination of crack growth, an artificial cUt is made in the testpiece to initiate cUt growth.
Ceramic tiles – Definitions, classification, characteristics and marking (Second revision) (ISO 13006:2018, MOD)
MS ISO 13006:2020Status : 2nd Revision
Format : PDF
This docUment defines terms and establishes classifications, characteristics and marking reqUirements fo ....Read more