Road vehicles – Information for first and second responders – Part 2: Rescue sheet for buses, coaches and heavy commercial vehicles (ISO 17840-2:2019, IDT) (Published by Department of Standards Malaysia in 2024)
MS ISO 17840-2:2019Status : Original
Format : PDF
This document defines the content and the layout of the rescue sheet providing necessary and useful information about a vehicle involved in an accident/incident to support the rescue team in rescuing ....Read more
Road vehicles – Information for first and second responders – Part 1: Rescue sheet for passenger cars and light commercial vehicles (ISO 17840-1:2022, IDT) (Published by Department of Standards Malaysia in 2024)
MS ISO 17840-1:2022Status : Original
Format : PDF
This document defines the contents and the layout of the rescue sheet providing necessary and useful information about a vehicle involved in an accident to support the rescue team extricating the occu ....Read more
Motor vehicle aftermarket - Smash repair - Requirements
MS 2726:2024Status : Original
Format : PDF
This Malaysian Standard specifies requirements for smash repair workshop activities including motor vehicle body panel repair and motor vehicle refinishing with regards to management systems requireme ....Read more
Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 7: Guidance for the assessment of conformity (First revision) (ISO/TS 15876-7:2018, MOD)
MS 2763-7:2024Status : 1st Revision
Format : PDF
This document gives requirements and guidance for the assessment of conformity of compounds, products, and assemblies in accordance with the applicable part(s) of ISO 15876 intended to be included in ....Read more
Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 5: Fitness for purpose of the system (First revision) (ISO 15876-5:2017 and its AMENDMENT 1:2020, MOD)
MS 2763-5:2024Status : 1st Revision
Format : PDF
This document specifies the characteristics of the fitness for purpose of polybutene-1 (PB-1) piping systems, intended to be used for hot and cold water installations within buildings for the conveyan ....Read more
Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 3: Fittings (First revision) (ISO 15876-3:2017 and its AMENDMENT 1:2020 and AMENDMENT 2:2021, MOD)
MS 2763-3:2024Status : 1st Revision
Format : PDF
This document specifies the characteristics of fittings for polybutene-1 (PB-1) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, wh ....Read more
Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 2: Pipes (First revision) (ISO 15876-2:2017 and its AMENDMENT 1:2020, MOD)
MS 2763-2:2024Status : 1st Revision
Format : PDF
This document specifies the characteristics of pipes for polybutene-1 (PB-1) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whethe ....Read more
Plastics piping systems for hot and cold water installations - Polybutylene (PB) - Part 1: General (First revision) (ISO 15876-1:2017, MOD)
MS 2763-1:2024Status : 1st Revision
Format : PDF
This document specifies the general aspects of polybutene-1 (PB-1) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not i ....Read more
Water dispenser for household use - Method of measuring the performance
MS 2799:2024Status : Original
Format : PDF
This Malaysian Standard specifies method for measuring the performance of storage and instant hot & cold water dispensers with a maximum rated voltage does not exceeding 250 V for household use.
Natural rubber and butyl rubber inner tubes for motorised vehicles - Specification (Second revision)
MS 868:2024Status : 2nd Revision
Format : PDF
This Malaysian Standard applies to inner tubes natural rubber and butyl rubber for pneumatic tyres.