• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • Sign In
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




PLASTICS – DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD – PART 2: PLASTICS AND EBONITE (FIRST REVISION) (ISO 75-2:2004, IDT)
MS ISO 75-2:2007
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies three methods, using different values of constant flexural stress, that can be used for the determination of the temperature of deflection under load of plastics (inc ....Read more luding filled plastics and fibre-reinforced plastics in which the fibre length, prior to processing, is up to 7,5 mm) and ebonite: method A, using a flexural stress of 1,80 MPa; method B, using a flexural stress of 0,45 MPa; method C, using a flexural stress of 8,00 MPa.

The Malaysian Standard deflection ?s used to determine the temperature of deflection under load corresponds to a flexuralstrain increase ? ? f defined in this part of ISO 75. The initial flexural strain due to the loading of the specimen at room temperature is neither specified nor measured in this part of ISO 75. The ratio of this flexural-strain difference to the initial flexural strain depends on the modulus of elasticity, at room temperature, of the material under test.

This Malaysian Standard is therefore only suita Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



PLASTICS – DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD – PART 1: GENERAL TEST METHOD (FIRST REVISION) (ISO 75-1:2004, IDT)
MS ISO 75-1:2007
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies methods for the determination of the temperature of deflection under load (flexural stress under three-point loading) of plastics. Different types of test specimen an ....Read more d different constant loads are defined to suit different types of material.

This Malaysian Standard gives a general test method, part 2 gives specific requirements for plastics (including filled plastics and fibre-reinforced plastics in which the fibre length, prior to processing, is up to 7,5 mm) and ebonite while part 3 gives specific requirements for high-strength thermosetting laminates and long-fibre-reinforced plastics in which the fibre length is greater than 7,5 mm.

This Malaysian Standard specified are suitable for assessing the relative behaviour of different types of material at elevated temperature under load at a specified rate of temperature increase. The results obtained do not necessarily represent maximum applicable temperatures, because in practice essential factors suc Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



Specification for anchorages for seat belts (First revision)
MS 75:2002 (CONFIRMED:2023)
Status : 2nd Confirmation
Format : PDF

This Malaysian Standard specifies basic requirements for the locations and testing of anchorages for seat belts in motor vehicles for the attachment of seat belt assemblies,specified in MS 1175.

RM 30.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR CONTAINERS FOR LEAD - ACID BATTERIES (FIRST REVISION)
MS 68 : 1991
Status : 1st Revision
Format : PDF

This Malaysian Standard lays down the requirements and the methods of test for containers normally used in the assembly of lead-acid storage batteries.

This Malaysian Standard specifies t ....Read more he synthetic resin and ebonite containers, hereinafter referred to as the “container”, to be used for lead-acid batteries. Close

RM 15.00

Document will be sent via email



 Add To Cart
ISO GENERAL PURPOSE METRIC SCREW THREADS – BASIC PROFILE PART 1: METRIC SCREW THREADS (ISO 68-1:1998, IDT)
MS ISO 68-1:2002 (CONFIRMED:2011)
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies the basic profile for ISO general purpose metric screw threads (M).

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



PLASTICS - DETERMINATION OF WATER ABSORPTION (FIRST REVISION) (ISO 62:2008, IDT)
MS ISO 62:2010
Status : 1st Revision
Format : PDF

This Malaysian Standard describes a procedure for determining the moisture absorption properties in the "through-the-thickness" direction of flat or curved-form solid plastics. This standard also desc ....Read more ribes procedures for determining the amount of water absorbed by plastic specimens of defined dimensions, when immersed in water or when subjected to humid air under controlled conditions. The "through-the-thickness" moisture diffusion coefficient can be determined for single-phase material by assuming Fickian diffusion behaviour with constant moisture absorption properties through the thickness of the test specimen. Close

RM 30.00

Document will be sent via email



 Add To Cart
Plastics - Determination of apparent density of material that can be poured from a specified funnel (ISO 60:1977, IDT)
MS ISO 60:2004 (CONFIRMED:2012)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies a method of determining the apparent density, i.e. the mass per unit of volume, of loose material (powder or granular material) that tan be poured from a funnel of sp ....Read more ecified design.

NOTE - For a method of determining the apparent density of loose moulding material that cannot be poured from a specified funnel.

When the method is applied to relatively coarse materials, rather variable results may be obtained, owing to the error introduced when a straightedge blade is drawn across the top of the cylinder.

A knowledge of apparent density is of limited value in estimating the relative fluffiness or bulk of moulding materials, unless their densities in the moulded condition are approximately the same. Close

RM 15.00

Document will be sent via email



 Add To Cart
METHOD FOR THE DETERMINATION OF THE NUMBER OF THREADS PER UNIT LENGTH IN WOVEN TEXTILE FABRICS
MS 55: Pt. 8:1972
Status : Withdrawn
Format : PDF

This Malaysian Standard describes three methods for determining the number of threads per unit length in woven fabrics, namely:

(a) Method A — Determination by Square Counting Glass....Read more r /> (b) Method B — Determination by Traversing Thread Counter
(c) Method C — Determination by Thread Ravelling Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



SPECIFICATION FOR MAGNESIUM SULPHATE, FERTILIZER GRADE (SECOND REVISION)
MS 54 : 2001
Status : 2nd Revision
Format : PDF

This Malaysian Standard specifies the requirements for magnesium sulphate, fertilizer grade.

RM 15.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR AMMONIUM NITRATE FERTILIZER (FIRST REVISION)
MS 53 : 1993
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies requirements for ammonium nitrate fertilizers.

RM 15.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 557
  • 558
  • 559
  • 560
  • 561
  • 562
  • 563
  • ...
  • 580
  • 581
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.