• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • Sign In
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts (First revision) (ISO 286-2:2010, IDT)
MS ISO 286-2:2011
Status : Withdrawn
Format : PDF

This part of ISO 286 gives values of the limit deviations for commonly used tolerance classes for holes and shafts calculated from the tables given in ISO 286-1. This part of ISO 286 covers values for ....Read more the upper limit deviations ES (for holes) and es (for shafts), and the lower limit deviations EI (for holes) and ei (for shafts) (see Figures 1 and 2).
NOTE In the tables of limit deviations, the values of the upper limit deviation ES or es are shown above the values of the lower limit deviation EI or ei except for tolerance classes JS and js which are symmetrical about the zero line.
The ISO system for tolerances on linear size provides a system of tolerances and deviations suitable for features of the following types:
a) cylinders;
b) two parallel opposite surfaces.
For simplicity, and also because of the importance of cylindrical workpieces of circular section, only these are referred to explicitly. It should be clearly understood, however, that the tolerances and deviations given in this part of ISO 286 equally apply to workpieces of other than circular sections.
In particular, the term “hole” or “shaft” is used to designate features of the cylinder type (e.g. for the tolerancing of the diameter of a hole or shaft) and, for simplicity, these terms are also used for two parallel opposite surfaces (e.g. for the tolerancing of the thickness of a key or the width of a slot).
For further information on terminology, symbols, the basis of the system, etc., see ISO 286-1. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



SPECIFICATION FOR PAPER (DUPLICATING, COPY, LIQUID PROCESS)
MS 285:1975 (Previously numbered as MS 1.77:1975) (CONFIRMED:2003)
Status : Withdrawal without replacement
Format : PDF

This Malaysian Standard Specification applies to white and coloured paper intended for use in liquid process (spirit) duplicating, printing, copying pen-and-ink writing and typewriting.

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



SPECIFICATION FOR CARBON PAPER, HANDWRITING
MS 284:1975 (CONFIRMED:2003)
Status : Original
Format : PDF

This Malaysian Standard prescribes the requirements and the methods of sampling and test for carbon papers, for making carbon copies with pencil or pen.

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



SPECIFICATION FOR CARBON PAPER FOR TYPEWRITERS (FIRST REVISION)
MS 283:1986
Status : 1st Revision
Format : PDF

This Malaysian Standard prescribes the requirements and the methods of test for carbon paper for use with typewriters.

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



Natural rubber latex concentrate - Part 16: Determination of pH (Fourth revision)
MS 281-16:2012
Status : Original
Format : PDF

This Malaysian Standard specifies a method for the determination of the pH of natural rubber
latex concentrate by means of a pH meter equipped with a combined glass and silver
reference el ....Read more ectrode.
NOTE. It is also suitable for synthetic latices, pre-vulcanized latex, compounds containing polymer dispersions or
rubber latices including adhesives. Close

RM 15.00

Document will be sent via email



 Add To Cart
NATURAL RUBBER LATEX CONCENTRATE - PART 5: DETERMINATION OF MECHANICAL STABILITY (FOURTH REVISION)
MS 281-5:2010
Status : 4th Revision
Format : PDF

This Malaysian Standard specifies a method for the determination of the mechanical stability of natural rubber latex concentrate.

RM 15.00

Document will be sent via email



 Add To Cart
NATURAL RUBBER LATEX CONCENTRATE - PART 3: DETERMINATION OF DRY RUBBER CONTENT (FOURTH REVISION)
MS 281-3:2009
Status : 4th Revision
Format : PDF

This Malaysian Standard specifies a method for the determination of the dry rubber content of natural rubber latex concentrate.

RM 15.00

Document will be sent via email



 Add To Cart
NATURAL RUBBER LATEX CONCENTRATE - PART 17: DETERMINATION OF ZINC OXIDE STABILITY TIME (ZST)
MS 281: PART 17:2007
Status : Original
Format : PDF

This Malaysian Standard specifies a method for the determination of zinc oxide stability of natural rubber latex concentrate. It is also suitable for compounded latices.

RM 15.00

Document will be sent via email



 Add To Cart
NATURAL RUBBER LATEX CONCENTRATE – PART 18: DETERMINATION OF ZINC OXIDE VISCOSITY (ZOV)
MS 281: PART 18:2007
Status : Original
Format : PDF

This Malaysian Standard specifies a method for the determination of the zinc oxide viscosity of natural rubber latex concentrate.

RM 15.00

Document will be sent via email



 Add To Cart
NATURAL RUBBER LATEX CONCENTRATE - PART 11: DETERMINATION OF KOH NUMBER (FOURTH REVISION)
MS 281-11:2011
Status : 3rd Revision
Format : PDF

This Malaysian Standard specifies a method for the determination of the KOH number of natural rubber latex concentrate which is preserved wholly or in part with ammonia. The method is applicable to la ....Read more tices containing boric acid. The method is not applicable to latices preserved with potassium hydroxide. It is not necessarily suitable for latices from natural sources other than Hevea brasiliensis, or for latices of synthetic rubber, compounded latex, vulcanized latex or artificial dispersions of rubber. Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 524
  • 525
  • 526
  • 527
  • 528
  • 529
  • 530
  • ...
  • 580
  • 581
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.