• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




SPECIFICATION FOR STRAIGHT MINERAL LUBRICATING OILS (FIRST REVISION)
MS 381:1983
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies requirements for three levels of quality for straight mineral lubricating oils classified according to viscosity and viscosity index, as follows:

(a) Ta ....Read more ble 1 (grades TLS 10 to TLS 1500). Oils for total loss systems (TLS) with viscosities specified at one temperature only.

(b) Table 2A (grades CSA 15 to CSA1500). Oils for circulating systems (CS) with a minimum viscosity index (VI) of 35.

(c) Table 2B (grades CSB 10 to CSB 1000).Oils for circulating systems (CS) with a minimum viscosity index (VI) of 70. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



SPECIFICATION FOR STEAM TURBINE OILS(FIRST REVISION)
MS 380:1983
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies lubricating oils for steam turbines in four grades of differing viscosity ranges, but does not cover oils of the extreme pressure (E.P.) type.

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



SPECIFICATION FOR MASTIC ASPHALT FOR USE IN WATER-PROOFING (FIRST REVISION)
MS 378 : 1995
Status : 1st Revision
Format : PDF

This Malaysian Standard covers materials for mastic asphalt suitable for use inwater-proofing, consisting of asphaltic cement, mineral filter and mineralaggregrate.

The material covered ....Read more by this standard is suitable for water-proofing the floors of buildings and bridges, for reservoirs, waterways, subways and similar structures.It is not intended for use as a pavement for either foot or vehicular traffic. Close

RM 15.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR SODIUM CARBONATE (TECHNICAL GRADE)
MS 377:1976 (CONFIRMED:2004)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard Specification describes the requirements for sodium carbonate (soda ash) of the technical grade.

The requirements given in this standard shall cover essentially t ....Read more wo types of sodium carbonate. The first type shall be sodium carbonate decahydrate, while the second type is the anhydrous sodium carbonate. Close

RM 30.00

Document will be sent via email



 Add To Cart
ENGINE OILS - SPECIFICATION (SECOND REVISION)
MS 376:2010
Status : 2nd Revision
Format : PDF

This Malaysian Standard specifies requirement for engine oils.

This standard is applicable to all automotive gasoline and diesel engines, and also high speed industrial diesel engines.

RM 45.00

Document will be sent via email



 Add To Cart
Metallic materials - Calibration of force-proving instruments used for the verification of uniaxial testing machines (First revision) (ISO 376:2011, IDT)
MS ISO 376:2015
Status : 1st Revision
Format : PDF

This International Standard specifies a method for the calibration of force-proving instruments used for the
static verification of uniaxial testing machines (e.g. tension/compression testing ma ....Read more chines) and describes a
procedure for the classification of these instruments.
This International Standard is applicable to force-proving instruments in which the force is determined by
measuring the elastic deformation of a loaded member or a quantity which is proportional to it Close

RM 60.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR BITUMINOUS EMULSIONS USED AS A PROTECTIVE COATING FOR ROOFING (FIRST REVISION)
MS 375:1995
Status : 1st Revision
Format : PDF

This Malaysian Standard covers emulsified bitumen suitable for use as a protective coating for built-up roofs and other exposed surfaces with inclines of not less than 4% or 42 mm/m. 

RM 30.00

Document will be sent via email



 Add To Cart
SPECIFICATION FOR INJECTABLE PREPARATIONS (FIRST REVISION)
MS 372 : 1986
Status : 1st Revision
Format : PDF

This Malaysian Standard Specification prescribes the requirements for injectable preparations.

RM 45.00

Document will be sent via email



 Add To Cart
MEASUREMENT OF NOISE EMITTED BY ACCELERATING ROAD VEHICLES - ENGINEERING METHOD - PART 1: M AND N CATEGORIES (FIRST REVISION) (ISO 362-1:2007, COR 1:2009, IDT)
MS ISO 362-1:2010
Status : 1st Revision
Format : PDF

The adoption of the ISO Standard as a Malaysian Standard was recommended by the
Technical Committee on Pollution and Energy under the authority of the Industry Standards
Committee on Road ....Read more Vehicles.
This Malaysian Standard is the first revision of MS 1213, Method of test for the measurement
of noise emitted by accelerating motor vehicles - Engineering method.
This Malaysian Standard is identical with ISO 362-1:2007, Measurement of noise emitted by
accelerating road vehicles - Engineering method - Part 1: M and N categories, including its
Technical Corrigendum 1:2009, published by the International Organization for
Standardization (ISO). However, for the purposes of this Malaysian Standard, the following
apply:
a) in the source text, "this International Standard" should read "this Malaysian Standard";
and
b) the comma which is used as a decimal sign (if any), to read as a point.
This Malaysian Standard cancels and replaces MS 1213:1991.
Compliance with a Malaysian Standard does not of itself confer immunity from legal
obligations Close

RM 105.00

Document will be sent via email



 Add To Cart
MEASUREMENT OF NOISE EMITTED BY ACCELERATING ROAD VEHICLES - ENGINEERING METHOD - PART 2: L CATEGORY (ISO 362-2:2009, IDT)
MS ISO 362-2:2011 (CONFIRMED:2024)
Status : 2nd Confirmation
Format : PDF

The adoption of the ISO Standard as a Malaysian Standard was recommended by the
Technical Committee on Pollution and Energy under the authority of the Industry Standards Committee on Road Vehic ....Read more les.
This Malaysian Standard is identical with ISO 362-2:2009, Measurement of noise emitted by accelerating road vehicles - Engineering method - Part 2: L category, published by the International Organization for Standardization (ISO). However, for the purposes of this Malaysian Standard, the following apply:
a) in the source text, "this International Standard" should read "this Malaysian Standard";
and
b) the comma which is used as a decimal sign (if any), to read as a point.
Compliance with a Malaysian Standard does not of itself confer immunity from legal
obligations. Close

RM 60.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 518
  • 519
  • 520
  • 521
  • 522
  • 523
  • 524
  • ...
  • 580
  • 581
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.