• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • Sign In
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Medical electrical equipment - Part 2-35: Particular requirements for the basic safety and essential performance of heating devices using blankets, pads or mattresses and intended for heating in medical use (First revision) (IEC 80601-2-35:2009, IDT)
MS IEC 80601-2-35:2018
Status : 1st Revision
Format : PDF

This International Standard applies to the BASIC SAFETY and ESSENTIAL PERFORMANCE of
HEATING DEVICES using BLANKETS, PADS or MATTRESSES in medical use, also referred to as
ME EQUIPMENT. HE ....Read more ATING DEVICES intended to prewarm a bed are included in the scope of this
International Standard.
If a clause or subclause is specifically intended to be applicable to ME EQUIPMENT only, or to
ME SYSTEMS only, the title and content of that clause or subclause will say so. If that is not the
case, the clause or subclause applies both to ME EQUIPMENT and to ME SYSTEMS, as relevant.
If a clause or subclause is specifically intended to apply to a specifically defined type of ME
EQUIPMENT, as is the case with FORCED AIR DEVICES, then the clause or subclause is entitled as
such. Clauses or subclauses that apply to all types of ME EQUIPMENT within the scope of this
standard are not specifically entitled.
HAZARDS inherent in the intended physiological function of ME EQUIPMENT or ME SYSTEMS
within the scope of this standard are not covered by specific requirements in this standard
except in 7.2.13 and 8.4.1 of the general standard.
NOTE See also 4.2 of the general standard.
This particular standard does not apply to:
– HEATING DEVICES intended for physiotherapy;
– radiant warmers; for information, see IEC 60601-2-21 [12]2;
– incubators; for information, see IEC 60601-2-19 [10];
– transport incubators, for information, see IEC 60601-2-20 [11];
– cooling devices Close

RM 105.00

Document will be sent via email



 Add To Cart
Medical electrical equipmentPart 2-67: Particular requirements for basic safety and essential performance of oxygen conserving equipment (First revision) (ISO 80601-2-67:2014, IDT)
MS ISO 80601-2-67:2018
Status : 1st Revision
Format : PDF

IEC 60601-1:2005+A1:2012, 1.1 is replaced by:
This particular standard is applicable to the BASIC SAFETY and ESSENTIAL PERFORMANCE of oxygen
CONSERVING EQUIPMENT, hereafter referred to as ....Read more ME EQUIPMENT, in combination with its
ACCESSORIES intended to conserve supplemental oxygen by delivering gas intermittently and
synchronized with the PATIENT'S inspiratory cycle, when used in the HOME HEALTHCARE
ENVIRONMENT. Oxygen CONSERVING EQUIPMENT is typically used by a LAY OPERATOR.
NOTE 1 CONSERVING EQUIPMENT can also be used in professional health care facilities.
NOTE 2 CONSERVING EQUIPMENT can be used with an oxygen concentrator.
This particular standard is also applicable to those ACCESSORIES intended by their MANUFACTURER to
be connected to CONSERVING EQUIPMENT, where the characteristics of those ACCESSORIES can affect
the BASIC SAFETY or ESSENTIAL PERFORMANCE of the CONSERVING EQUIPMENT.
This particular standard is only applicable to active devices (e.g. pneumatically or electrically
powered) and is not applicable to non-active devices (e.g. reservoir cannulas).
NOTE 3 CONSERVING EQUIPMENT complying with this particular standard can be incorporated with other
devices that have their own standards, in which case the combination needs to comply with both standards.
EXAMPLES CONSERVING EQUIPMENT combined with a pressure regulator [2], an oxygen concentrator [1] or
liquid oxygen equipment [6].
If a clause or subclause is specifically intended to be applicable to ME EQUIPMENT only, or to
ME SYSTEMS only, the title and content of that clause or subclause will say so. If that is not the case,
the clause or subclause applies both to ME EQUIPMENT and to ME SYSTEMS, as relevant.
HAZARDS inherent in the intended function of ME EQUIPMENT or ME SYSTEMS within the scope of this
standard are not covered by specific requirements in this standard except in 7.2.13 and 8.4.1 of the
general standard.
NOTE 4 See also 4.2 of the general standard.
This particular standard is a particular standard in the IEC 60601 series of standards. Close

RM 90.00

Document will be sent via email



 Add To Cart
Medical electrical equipment - Part 2-50: Particular requirements for the basic safety and essential performance of infant phototherapy equipment (First revision) (IEC 60601-2-50:2016, IDT)
MS IEC 60601-2-50:2018
Status : 1st Revision
Format : PDF

This International Standard applies to the BASIC SAFETY and ESSENTIAL PERFORMANCE of INFANT PHOTOTHERAPY EQUIPMENT, as defined in 201.3.203 of this standard, also referred to as ME EQUIPMENT.
< ....Read more br /> If a clause or subclause is specifically intended to be applicable to ME EQUIPMENT only, or to ME SYSTEMS only, the title and content of that clause or subclause will say so. If that is not the case, the clause or subclause applies both to ME EQUIPMENT and to ME SYSTEMS, as relevant.

HAZARDS inherent in the intended physiological function of ME EQUIPMENT or ME SYSTEMS within the scope of this standard are not covered by specific requirements in this standard except in 7.2.13 and 8.4.1 of the general standard.

NOTE See also 4.2 of the general standard.

This particular standard specifies safety requirements for INFANT PHOTOTHERAPY EQUIPMENT, but alternate methods of compliance with a specific clause by demonstrating equivalent safety will not be judged as non-compliant if the MANUFACTURER has demonstrated in his RISK MANAGEMENT FILE that the RISK presented by the HAZARD has been found to be of an acceptable level when weighed against the benefit of treatment from the device.

This particular standard does not apply to:
– devices supplying heat via BLANKETS, PADS or MATTRESSES in medical use, for information
see IEC 80601-2-35;
– INFANT INCUBATORS; for information see IEC 60601-2-19;
– INFANT TRANSPORT INCUBATORS; for information, see IEC 60601-2-20;
– INFANT RADIANT WARMERS; for information see IEC 60601-2-21. Close

RM 45.00

Document will be sent via email



 Add To Cart
Medical electrical equipment-Part 2-19: Particular requirements for the basic safety and essential performance of infant incubators (First revision) (IEC 60601-2-19:2016, IDT)
MS IEC 60601-2-19:2018
Status : 1st Revision
Format : PDF

This International Standard applies to the BASIC SAFETY and ESSENTIAL PERFORMANCE of INFANT INCUBATORS, as defined in 201.3.209 of this standard, also referred to as ME EQUIPMENT.

If a ....Read more clause or subclause is specifically intended to be applicable to ME EQUIPMENT only, or to ME SYSTEMS only, the title and content of that clause or subclause will say so. If that is not the case, the clause or subclause applies both to ME EQUIPMENT and to ME SYSTEMS, as relevant.

HAZARDS inherent in the intended physiological function of ME EQUIPMENT or ME SYSTEMS within the scope of this standard are not covered by specific requirements in this standard except in 7.2.13 and 8.4.1 of the general standard.

NOTE See also 4.2 of the general standard.

This particular standard specifies safety requirements for INFANT INCUBATORS but alternate methods of compliance with a specific clause by demonstrating equivalent safety will not be judged as non-compliant if the MANUFACTURER has demonstrated in his RISK MANAGEMENT FILE that the RISK presented by the HAZARD has been found to be of an acceptable level when weighed against the benefit of treatment from the device.

This particular standard does not apply to:

– devices supplying heat via BLANKETS, PADS or MATTRESSES in medical use; for information see IEC 80601-2-35 [3]2);
– INFANT RADIANT WARMERS; for information, see IEC 60601-2-21 [2];
– INFANT TRANSPORT INCUBATORS, for information, see IEC 60601-2-20 [1];
– INFANT PHOTOTHERAPY EQUIPMENT, for information see IEC 60601-2-50 [4] Close

RM 60.00

Document will be sent via email



 Add To Cart
FLUIDS FOR ELECTROTECHNICAL APPLICATIONS - UNUSED MINERAL INSULATING OILS FOR TRANSFORMERS AND SWITCHGEAR
MS 2322:2010
Status : Original
Format : PDF

This Malaysian Standard covers specifications and test methods for unused mineral insulating
oils. It applies to oil delivered to the agreed point and time of delivery, intended for use in
....Read more transformers, switchgear and similar electrical equipment in which oil is required as an
insulant and for heat transfer. These oils are obtained by distillation and refining of crude
petroleum. Oils with and without additives are both within the scope of this standard.
This standard is applicable only to unused mineral insulating oils. Reclaimed oils are beyond
the scope of this standard. This standard does not apply to mineral oils used as impregnants
in cables or capacitors.
NOTE. Mineral insulating oils complying with the requirements of this standard, of the same class and containing no
additives (see 3.4), are considered to be compatible with one another and can be mixed in any proportion. This does
not apply to oils containing additives. Where the user wishes to mix such oils, a check is recommended to be made to
ensure that the mixture meets the requirements of this standard. Close

RM 30.00

Document will be sent via email



 Add To Cart
RUBBER, VULCANIZED OR THERMOPLASTIC – DETERMINATION OF TENSION SET UNDER CONSTANT ELONGATION, AND OF TENSION SET, ELONGATION AND CREEP UNDER CONSTANT TENSILE LOAD (SECOND REVISION) (ISO 2285:2007, IDT)
MS ISO 2285:2007
Status : 2nd Revision
Format : PDF

This International Standard specifies a number of methods of determining the dimensional changes in test
pieces of vulcanized or thermoplastic rubber during and after tensile loading for relativ ....Read more ely short periods under
constant elongation or constant loading.
The constant-elongation test is intended to measure the ability of rubbers to retain their elastic properties after
extension, at a standard laboratory temperature, to a specified strain which is maintained for a specified time
at the same or at a specified higher temperature and then released at the test temperature or at the standard
laboratory temperature.
The constant-load test specifies a method for the determination of elongation, creep and tension set of
rubbers subjected to a constant load at standard laboratory temperature.
The test methods are intended to measure the elastic properties of rubber in the hardness range 20 IRHD to
94 IRHD.
The creep measurement is not recommended for product design or the evaluation of low-creep materials. For
these, reference should be made to ISO 8013. No agreement between the results of this test or those of
ISO 8013 should be inferred.
NOTE The constant-load test is primarily intended for the measurement of state of cure and the quality control of
thin-walled products. An increase in the state of cure or degree of crosslinking is usually reflected in a decrease in set,
creep or elongation. Close

RM 30.00

Document will be sent via email



 Add To Cart
Medical electrical equipment - Part 2-20: Particular requirements for the basic safety and essential performance of infant transport incubators (First revision) (IEC 60601-2-20:2016, IDT)
MS IEC 60601-2-20:2018
Status : 1st Revision
Format : PDF

This International Standard applies to the BASIC SAFETY and ESSENTIAL PERFORMANCE of INFANT TRANSPORT INCUBATOR equipment, as defined in 201.3.211 of this standard, also referred to as ME EQUIPMENT.....Read more r />
If a clause or subclause is specifically intended to be applicable to ME EQUIPMENT
only, or to ME SYSTEMS only, the title and content of that clause or subclause will say so. If that is not the case, the clause or subclause applies both to ME EQUIPMENT and to ME SYSTEMS, as relevant. HAZARDS inherent in the intended physiological function of ME EQUIPMENT or ME SYSTEMS within the scope of this standard are not covered by specific requirements in this standard except in 7.2.13 and 8.4.1 of the general standard.

NOTE See also 4.2 of the general standard.

This particular standard specifies safety requirements for INFANT TRANSPORT INCUBATORS but alternate methods of compliance with a specific clause by demonstrating equivalent safety will not be judged as non compliant if the MANUFACTURER has demonstrated in his RISK MANAGEMENT FILE that the RISK presented by the HAZARD has been found to be of an acceptable level when weighed against the benefit of treatment from the device.

This particular standard does not apply to:

– devices supplying heat via BLANKETS, PADS or MATTRESSES in medical use; for information see IEC 80601-2-35 [1]1);
– INFANT INCUBATORS which are not INFANT TRANSPORT INCUBATOR; for information see IEC 60601-2-19 [2];
– INFANT RADIANT WARMERS; for information, see IEC 60601-2-21 [3];
– INFANT PHOTOTHERAPY; for information, see IEC 60601-2-50 [4]. Close

RM 75.00

Document will be sent via email



 Add To Cart
Optics and photonics-Lasers and laser-related equipment-Test methods for laser beam power, energy and temporal characteristics (ISO 11554:2017,IDT)
MS ISO 11554:2019
Status : Original
Format : PDF

This document specifies test methods for determining the power and energy of continuous wave and pulsed laser beams, as well as their temporal characteristics of pulse shape, pulse duration and pulse ....Read more repetition rate. Test and evaluation methods are also given for the power stability of cw-lasers, energy stability of pulsed lasers and pulse duration stability.

The test methods given in this document are used for the testing and characterization of lasers. Close

RM 45.00

Document will be sent via email



 Add To Cart
TERMINOLOGY RELATING TO LIME AND LIMESTONE (AS USED BY THE INDUSTRY)
MS 1996:2007
Status : Original
Format : PDF

1.1 This terminology refers to the terms relating to lime and limestone products as used by the industry.
1.2 Where appropriate, the various terms defined below should be prefixed with one or ot ....Read more her of the adjectives "highcalcium," "magnesian," or "dolomitic". (Examples: dolomitic quicklime; high-calcium hydraulic hydrated lime; magnesian or
dolomitic limestone).
1.3 The composition of a limestone should be given in terms of a percentage of the carbonates present. In limestone of
interest to the lime industry, it is usually assumed that the material consists almost entirely of carbonates. Where this
assumption is not valid, the percentage of noncarbonate material should be determined, and the composition expressed in terms
of the carbonate material present.
1.4 For specific application of lime or a limestone product, see the appropriate ASTM specification. Close

RM 15.00

Document will be sent via email



 Add To Cart
Auxiliaries for lamps - Capacitors for use in tubular fluorescent and other discharge lamp circuits - General and safety requirements (Second revision) (IEC 61048:2006, AMD. 1:2015, IDT)
MS IEC 61048:2019
Status : 2nd Revision
Format : PDF

continuously rated a.c. capacitors of up to and including 2,5 kVAr, and not less than 0,1 μF,
having a rated voltage not exceeding 1 000 V, which are intended for use in discharge lamp
ci ....Read more rcuits operating at 50 Hz or 60 Hz and at altitudes up to 3 000 m.
NOTE These lamps and associated ballasts are covered by IEC 60081, IEC 60901, IEC 60188, IEC 60192,
IEC 60662, and IEC 61167 and by IEC 61347-2-8 and IEC 61347-2-9, respectively.
It covers capacitors intended for connection in shunt or in series with the lamp circuit or an
effective combination of these.
It covers only impregnated or unimpregnated capacitors, having a dielectric of paper, plastic
film or a combination of both, either metallized or with metal foil electrodes.
This standard does not cover radio-interference suppressor capacitors the requirements for
which are found in IEC 60384-14.
Tests given in this standard are type tests. Requirements for testing individual capacitors
during production are not included. Close

RM 60.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • ...
  • 580
  • 581
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.