• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • Sign In
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




SPECIFICATION FOR AGGREGATES FROM NATURAL SOURCES FOR CONCRETE (FIRST REVISION)
MS 29 : 1995
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies the quality and grading requirements for aggregates
obtained by processing natural materials for use in concrete. (For lightweight aggregates, see
BS 3797 ....Read more .) Close

RM 30.00

Document will be sent via email



 Add To Cart
Batik Malaysia - Spesifikasi (Semakan kedua)
MS 692:2019 (BM)
Status : 2nd Revision
Format : PDF

Malaysian Standard ini menetapkan keperluan bahan, teknik, proses, keperluan, kaedah ujian, nilai estetika, penandaan dan pelabelan bagi Batik Malaysia.

RM 45.00

Document will be sent via email



 Add To Cart
Household and similar electrical appliances - Safety - Part 2-80: Particular requirements for fans (Fourth revision) (IEC 60335-2-80:2015, MOD)
MS 1597-2-80:2019
Status : 3rd Revision
Format : PDF

This clause of Part 1 is replaced by the following.
This International Standard deals with the safety of electric fans for household and similar purposes, their rated voltage being not more than ....Read more 250 V for single-phase appliances and 480 V for other appliances.
NOTE 101. Examples of fans that are within the scope of this standard are
- ceiling fans;
- duct fans;
- partition fans;
- pedestal fans;
- table fans.
This standard also applies to separate controls supplied with fans.
Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended for use in shops, in light industry and on farms, are within the scope of this standard.
As far as is practicable, this standard deals with the common hazards presented by appliances that are encountered by all persons in and around the home. However, in general, it does not take into account;
- persons (including children) whose
• physical, sensory or mental capabilities; or
• lack of experience and knowledge
- prevents them from using the appliance safely without supervision or instruction;
- children playing with the appliance.
NOTE 102. Attention is drawn to the fact that
- for appliances intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary;
- in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour and similar authorities. Close

RM 45.00

Document will be sent via email



 Add To Cart
Paint and coating system for naval vessels
MS 2628:2017
Status : Original
Format : PDF

specifications and colour code for use on naval vessels and naval offshore stations.
1.1 The field of application is characterized by:
a) The type of substrate and surface preparation;
....Read more /> b) The type of location;
c) The type of application for protective paint and coating system; and
d) Although this standard only covers the paint and coating system specifications for naval vessel and naval offshore station, it may by agreement also be applied to those cases which are not covered by the standard.
1.2 The paint and coating system specification includes the protection against wear or corrosive attack, and also enhances its appearance at the following locations:
a) Complete immersion (underwater area);
b) Splash zone (boot topping);
c) Upper hull (top sides) and super structures;
d) Decks;
e) Tanks and cargo spaces;
f) Interiors;
g) High heat and fire exposure areas; and
h) Other special fittings and areas. Close

RM 120.00

Document will be sent via email



 Add To Cart
Assessment service delivery — Procedures and methods to assess people in work and organizational settings - Part 2: Requirements for service providers (ISO 10667-2:2011, IDT)
MS ISO 10667-2:2017
Status : Original
Format : PDF

This part of MS ISO 10667 establishes requirements and guidance for the client working with the service provider to carry out the assessment of an individual, a group, or an organization for work-rela ....Read more ted purposes. This part of MS ISO 10667 enables the client to base its decisions on sound assessment results.
This part of MS ISO 10667 specifies the requirements of the client with respect to:
a) the needs and rationale for using assessments;
b) the conditions under which the assessment will be used;
c) the decisions about the assessment approach together with the implementation and evaluation of assessment procedures and methods;
d) the required competence and professionalism of the client’s employees who are involved in the assessment process;
e) the decisions about the access, use, and storage of assessment results and subsequent reports;
f) organizational-related decisions, e.g. training, team building, ascertaining organizational culture or morale.
This part of MS ISO 10667 also specifies assessment methods and procedures that can be carried out for one or more of the following work-related purposes made by or affecting individuals, groups or organizations, including, but not limited to:
— employment-related decisions, e.g. recruitment, selection, development, appraisal, promotion, outplacement, succession planning and reassignment;
— career-related decisions, e.g. recruiting, coaching, guidance, vocational rehabilitation and outplacement counselling;
— group decisions, e.g. training initiatives, team building, etc.;
— organization decisions, e.g. restructuring, morale and culture initiatives, mergers and acquisitions, etc.
No technical professional standards form part of MS ISO 10667. However, the quality of assessment procedures and methods should be considered in relation to the purposes of the assessment, the relevance of the measures involved, their validity, reliability, equity, standardization and any issues relating to special needs of the assessment participant and other factors that affect the practicality, acceptability and utility of the assessment.
NOTES:
1. Requirements for the service provider are specified in MS ISO 10667-2.
2. See Bibliography for examples of various professional guidelines.
3. See Annex B for further details of generally accepted technical quality guidelines.
This part of MS ISO 10667 does not detail the specific competences required for assessors as these are dependent upon the nature of the assessment.
4. See Annex C for further information on assessor competence. Close

RM 60.00

Document will be sent via email



 Add To Cart
Assessment service delivery - Procedures and methods to assess people in work and organizational settings - Part 1: Requirements for the client (ISO 10667-1:2011, IDT)
MS ISO 10667-1:2017
Status : Original
Format : PDF

This part of MS ISO 10667 establishes requirements and guidance for the client working with the service provider to carry out the assessment of an individual, a group, or an organization for work-rela ....Read more ted purposes. This part of MS ISO 10667 enables the client to base its decisions on sound assessment results.
This part of MS ISO 10667 specifies the requirements of the client with respect to:
a) the needs and rationale for using assessments;
b) the conditions under which the assessment will be used;
c) the decisions about the assessment approach together with the implementation and evaluation of assessment procedures and methods;
d) the required competence and professionalism of the client’s employees who are involved in the assessment process;
e) the decisions about the access, use, and storage of assessment results and subsequent reports;
f) organizational-related decisions, e.g. training, team building, ascertaining organizational culture or morale.
This part of MS ISO 10667 also specifies assessment methods and procedures that can be carried out for one or more of the following work-related purposes made by or affecting individuals, groups or organizations, including, but not limited to:
— employment-related decisions, e.g. recruitment, selection, development, appraisal, promotion, outplacement, succession planning and reassignment;
— career-related decisions, e.g. recruiting, coaching, guidance, vocational rehabilitation and outplacement counselling;
— group decisions, e.g. training initiatives, team building, etc.;
— organization decisions, e.g. restructuring, morale and culture initiatives, mergers and acquisitions, etc. Close

RM 45.00

Document will be sent via email



 Add To Cart
Code of practice for structural use of timber - Part 5: timber joints (First revision)
MS 544-5:2018
Status : 1st Revision
Format : PDF

This part of Malaysian Standard applies to joints in solid timbers fabricated with mechanical fasteners. These include joints fabricated with the following fasteners:
a) nails;
b) wood scr ....Read more ews;
c) bolts;
d) coach screws;
e) split-ring connectors;
f) shear-plate connectors; and
g) steel dowels.
For mechanical fasteners used in connections for engineered timber components (e.g. glue laminated timber or glulam, laminated veneer lumber (LVL), etc.), guidance is recommended to be obtained from their manufacturers on whether the joint design values based on solid timber are applicable for their products.
NOTES:
1. Design rules for specialised and patented mechanical fasteners and for variants of conventional fasteners are not included in this standard.
2. This standard does not specifically cover glued timber-to-timber or timber-to-plywood connections as occurred in fabricated components such as stressed skin panels or plywood webbed beams. In such cases, joint design can be based on the timber components in the connection, provided that the joints are fabricated using a rigid, durable adhesive. Phenolic type adhesives meet these requirements. The design of fabricated components comprising glued connections is therefore based on the fact that with correct bonding practice and quality control, a joint is developed in which the adhesive bond strength and durability will be superior to the components comprising the joints. Reference may be made to Appendix C3 of AS 1720.1:2010, for information on methods for assessing the deformation of joints. Close

RM 75.00

Document will be sent via email



 Add To Cart
Code of practice for structural use of timber - Part 3: Permissible stress design of glued laminated timber (First revision)
MS 544-3:2017 (CONFIRMED:2022)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard provides the guidelines on the structural use of glued laminated timber in include recommendation on quality, grade stresses and modification factors applicable to this materia ....Read more l when use as a simple member or as part of build-up components or as part of structure incorporating other materials. It also gives recommendation for design of mechanical and glued connections and it includes general advice on workmanship. Close

RM 45.00

Document will be sent via email



 Add To Cart
Code of practice for structural use of timber - Part 2: permissible stress design of solid timber (First revision)
MS 544-2:2017 (CONFIRMED:2022)
Status : 1st Confirmation
Format : PDF

This part of Malaysian Standard describes recommendations for the structural use of the Malaysian hardwood and softwood timber species in load bearing members. It includes recommendations on quality, ....Read more grade stresses and modification factors applicable to these timbers when used as simple members, or as parts of built-up components, or as parts of structures incorporating other materials. It does not, and it is not intended to deal comprehensively with all aspects of timber construction. In particular, it does not cover well tried and traditional methods of timber construction which have been employed successfully over a long period of time. Close

RM 90.00

Document will be sent via email



 Add To Cart
Code of practice for structural use of timber - Part 1: General (Second revision)
MS 544-1:2017 (CONFIRMED:2022)
Status : 1st Confirmation
Format : PDF

This part of Malaysian Standard provides guidance on the structural use of timber and timber-based products, in load bearing members. It includes recommendations on quality, grade stresses and modific ....Read more ation factors applicable to these materials when use as simple members or as parts of built-up components, or as parts of structures incorporating other materials. It also gives recommendations for the design of nailed, screwed, bolted, connectored and glued joints. In addition, it provides recommendations for a method of test to assess the adequacy of structural assemblies, and it includes general advice on workmanship, various treatments which can be applied, inspection and maintenance.

It does not, and it is not intended to, deal comprehensively with all aspects of timber construction. In particular, it does not cover well tried and traditional methods of timber construction which have been employed successfully over a long period of time. Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • ...
  • 580
  • 581
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.