• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Elastomeric teats for feeding bottles - Specification (Second revision)
MS 1082:2011
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies requirements for materials, design, performance, packaging
and marking for elastomeric teats for babies‘ feeding bottles which are not cleft lip or cleft pala ....Read more te
teats. It includes methods of test for those requirements and also recommendations for the use
and care of feed teats. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



BELT DRIVES - V-BELTS AND V-RIBBED BELTS, AND CORRESPONDING GROOVED PULLEYS - VOCABULARY (ISO 1081:1995, IDT)
MS ISO 1081:2008
Status : Original
Format : PDF

This Malaysian Standard defines terms relating to V-belt drives, V-belts and V-grooved pulleys, Vribbed belt drives, V-ribbed belts and V-ribbed pulleys, as well as the corresponding symbols.
Th ....Read more e general definitions are valid irrespective of the system describing the pulleys.
The dimensions of pulleys grooves can be defined either on the basis of the datum width or on the
basis of the effective width. As a result, two systems for the definition and description of the
dimensions of pulleys and belts have been developed. The two systems are independent of each
other. Close

RM 30.00

Document will be sent via email



 Add To Cart
METHOD OF TEST FOR DETERMINATION OF CATIONIC ACTIVE MATTER IN DETERGENTS - BY DIRECT TWO PHASE TITRATION PROCEDURE
MS 1081 : 1987
Status : Withdrawn
Format : PDF

This Malaysian Standard describes two methods for the determination of cationic active matter in detergents using the direct two-phase titration procedure. It is applicable to the analysis of cationic ....Read more active materials such as long-chain quaternary ammonium compounds. (benzyl-dimethyl-stearyl-ammonium chloride. benzyl-dimethyl-dodecyl-ammonium chloride etc.) salts of laurylamine, salts of imidazoline, etc.

Both methods are also applicable to solids or to aqueous solutions of the active material. The molar mass of thecattonic active matter must be known or previously determined if its content is expressed as a percentage by mass.

NOTE. Low molar mass sulphonates of toluene and syiene present as hydrotropes do not interfere when present in concentrations up to 1 5% (rn/rn) on active material. At higher levels, their influence shall be evaluated in each particular Case.

Non-ionic surface active agents. soap, urea and ethylenediaminetetra-acetic acid salts do not interfere.

Typical in Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



METHOD OF TEST FOR DETERMINATION OF TOTAL ANIONIC DETERGENT BY HYAMINE TITRATION
MS 1079 : 1987 (CONFIRMED:2025)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard describes a method for the determination of anionic detergent by Hyamine titration. It is applicable to the analysis of alkylbenzene suiphonates, alkylsulphonates, alkylsulphat ....Read more es and hydroxylsuiphates, alkylphenolethoxysulphates and fatty alcohol ethoxysulphates in detergent liquids, powders or household cleaners.

The total active detergent is determined if a mixture of sulphonates and/or sulphates is present (see note 1). The mean molecular weight of the active detergent(s) must be known. Sulphonates with low molecular weight such as toluene and xylene sulphonate do not interfere when present in concentrations up to 15% of active material. Close

RM 15.00

Document will be sent via email



 Add To Cart
METHODS OF TEST FOR BOILING POINT OF ENGINE COOLANTS / ANTIFREEZES
MS 1078 : 1987
Status : Original
Format : PDF

This Malaysian Standard, which had been approved by the Chemical and Pharmaceutical Industry
Standards Committee and endorsed by the Council of the Standards and Industrial Research
Instit ....Read more ute of Malaysia (SIRIM) was published under the authority of the SIRIM Council in July,
1987.
SIRIM wishes to draw attention to the fact that this Malaysian Standard does not purport to
include all the necessary provisions of a contract.
The Malaysian Standards are subject to periodical review to keep abreast of progress in the
industries concerned. Suggestions for improvements will be recorded and in due course brought
to the notice of the Committees charged with the revision of the standards to which they refer. Close

RM 15.00

Document will be sent via email



 Add To Cart
Brake fluids - Test method - Part 11: Effects on SAE SBR WC cups (First revision)
MS 1077-11:2012
Status : 1st Revision
Format : PDF

This Malaysian Standard describes a method for evaluating the effects of motor vehicle brake
fluids in swelling, softening and otherwise affecting standard Society of Automotive Engineers
....Read more (SAE) styrene-butadiene rubber (SBR) wheel cylinder (WC) cups. Close

RM 15.00

Document will be sent via email



 Add To Cart
Brake fluids - Test method - Part 5: Corrosion (Second revision)
MS 1077-5:2012
Status : 2nd Revision
Format : PDF

This Malaysian Standard describes a method for evaluating the corrosiveness of motor
vehicle brake fluid by running duplicate samples.

RM 30.00

Document will be sent via email



 Add To Cart
Brake fluids - Test method - Part 4: Fluid stability (Second revision)
MS 1077-4:2012
Status : 2nd Revision
Format : PDF

This Malaysian Standard describes a method for evaluating the heat temperature and
chemical stability of motor vehicle brake fluid.

RM 15.00

Document will be sent via email



 Add To Cart
Brake fluids - Test method - Part 12: Stroking properties (First revision)
MS 1077-12:2012
Status : 1st Revision
Format : PDF

This Malaysian Standard describes a method for evaluating the lubricating properties,
component compatibility, resistance to leakage and related qualities of a motor vehicle brake
fluids.

RM 30.00

Document will be sent via email



 Add To Cart
Brake fluids - Test method - Part 1: Equilibrium reflux boiling point (ERBP) (Second revision)
MS 1077-1:2012
Status : 2nd Revision
Format : PDF

This Malaysian Standard describes a method for determining the equilibrium reflux boiling
point (ERBP) of motor vehicle brake fluid.

RM 15.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 448
  • 449
  • 450
  • 451
  • 452
  • 453
  • 454
  • ...
  • 580
  • 581
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.