• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • Sign In
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Rubber - General procedures for preparing and conditioning test pieces for physical test methods (Second revision) (ISO 23529:2016, IDT)
MS ISO 23529:2020
Status : 2nd Revision
Format : PDF

This document specifies general procedures for the preparation, measurement, marking, storage, and
conditioning of rubber test pieces for use in physical tests specified in other International S ....Read more tandards,
and the preferred conditions to be used during the tests. Special conditions, applicable to a particular
test or material or simulating a particular climatic environment, are not included, nor are special
requirements for testing whole products.
This document also specifies the requirements for the time interval to be observed between forming
and testing of rubber test pieces and products. Such requirements are necessary to obtain reproducible
test results and to minimize disagreements between customer and supplier. Close

RM 30.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized or thermoplastic - Determination of shear modulus and adhesion to rigid plates - Part 1: Quadruple-shear methods (Second revision) (ISO 1827:2016, IDT)
MS ISO 1827:2020
Status : 2nd Revision
Format : PDF

This document specifies methods for the determination of the modulus in shear and the strength of
bonds of rubber to metal or other rigid plates, using rubber bonded between four parallel plates ....Read more .
Method A describes the determination of the modulus in shear.
Method B describes the determination of the strength of the bonds.
The methods are applicable primarily to test pieces prepared in the laboratory under standard
conditions, such as can be used to provide data for the development and control of rubber compounds
and methods of manufacture of bonded shear units. Close

RM 30.00

Document will be sent via email



 Add To Cart
Tekstil - Tenunan Malaysia - Bahagian 4: Tenun Dastar dan Tenun Rungus
MS 1747-4:2020
Status : Original
Format : PDF

Malaysian Standard ini menetapkan spesifikasi bagi bahan mentah yang digunakan dalam
proses tenunan, terma dan definisi yang berkaitan hasil tenunan serta proses tenunan,
struktur asas, ka ....Read more edah penjagaan, kriteria kualiti, penandaan dan pelabelan bagi Tenun Dastar
dan Tenun Rungus. Close

RM 45.00

Document will be sent via email



 Add To Cart
Rubber — Determination of ash — Part 2: Thermogravimetric analysis (TGA) (ISO 247-2:2018, IDT)
MS ISO 247-2:2020
Status : Original
Format : PDF

This document specifies two methods for the determination of ash from raw rubbers, compounded
rubbers and vulcanizates using a thermogravimetric analyser (TGA).
The methods are applicable ....Read more to raw, compounded or vulcanized rubbers of the M, O, R and U families
described in ISO 1629:
— Method A is applicable for the determination of the ash from raw rubbers.
— Method B is applicable for the determination of the ash from compounded or vulcanized rubbers.
The methods are not applicable for the determination of the ash from raw rubbers, compounded or
vulcanized rubbers containing chlorine, bromine or iodine.
This document does not cover the interpretation of the ash results from the inorganic chemical contents
of compounded or vulcanized rubbers. Close

RM 15.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized or thermoplastic - Determination of hardness - Part 9: Calibration and verification of hardness testers (ISO 48-9:2018, IDT)
MS ISO 48-9:2020
Status : Original
Format : PDF

This document specifies procedures for the calibration and verification of durometers of types A, D, AO
and AM (see ISO 48-4), IRHD pocket meters (see ISO 48-5), IRHD dead-load instruments (see ....Read more ISO 48-2)
and dead-load instruments using the very low rubber hardness scale (see ISO 48-3). Close

RM 45.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized or thermoplastic - Determination of hardness - Part 8: Apparent hardness of rubber-covered rollers by Pusey and Jones method (ISO 48-8:2018, IDT)
MS ISO 48-8:2020
Status : Original
Format : PDF

This document specifies a method for the determination of the apparent hardness of vulcanized- or
thermoplastic-rubber roller covers, expressed as the Pusey and Jones indentation value.
Th ....Read more e Pusey and Jones plastometer apparatus is used to measure the depth of indentation of an
indentor under a specified force into the surface of the rubber. The indentation value is not the same
as that measured by the international rubber hardness test method ISO 48-2, since in this method
the rubber immediately adjacent to the indentor is precompressed. The Pusey and Jones indentation
value is an inverse measurement of hardness, i.e. the harder the rubber the lower the Pusey and Jones
indentation value. Close

RM 30.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized or thermoplastic - Determination of hardness - Part 7: Apparent hardness of rubber-covered rollers by Shore-type durometer method (ISO 48-7:2018, IDT)
MS ISO 48-7:2020
Status : Original
Format : PDF

This document specifies a method for the determination of the apparent hardness of vulcanized- or
thermoplastic-rubber roller covers, expressed in Shore hardness, for measurement where only medi ....Read more um
precision is required. The method and apparatus used are essentially those described in ISO 48-4, the
measurements in this case being made on the curved surface of the conditioned rubber-covered roller
rather than on a flat test piece. Shore type A and type D instruments are specified, the latter being used
for measurements on rollers of high hardness.
NOTE With some rollers, there can be significant variation in the thickness of the rubber over the surface of
the roller, which could affect the measured apparent hardness. Close

RM 30.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized or thermoplastic - Determination of hardness - Part 6: Apparent hardness of rubber-covered rollers by IRHD method (ISO 48-6:2018, IDT)
MS ISO 48-6:2020
Status : Original
Format : PDF

This document specifies a method for the determination of the apparent hardness, expressed in
International Rubber Hardness Degrees (IRHD), of vulcanized- or thermoplastic-rubber roller covers.< ....Read more br /> The method is similar in principle to the methods used for the determination of the hardness of rubber
in ISO 48-2 in that it consists essentially of measuring the depth of penetration of a spherical indentor
operating under a specified force. The apparatus used is similar to that described in ISO 48-2, having a
base specifically designed for application to roller covers and similar curved surfaces.
NOTE With some rollers, there can be significant variation in the thickness of the rubber over the surface of
the roller, which could affect the measured apparent hardness. Close

RM 30.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized or thermoplastic - Determination of hardness - Part 5: Indentation hardness by IRHD pocket meter method (ISO 48-5:2018, IDT)
MS ISO 48-5:2020
Status : Original
Format : PDF

This document specifies a method for determining the indentation hardness of vulcanized or
thermoplastic rubber by means of a pocket hardness meter calibrated in IRHD. The use of such meters is< ....Read more br /> primarily intended for control, not specification, purposes (for specification, see ISO 48-2). It is possible
to increase precision by fixing the pocket hardness meter on a support. Close

RM 30.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized or thermoplastic - Determination of hardness - Part 4: Indentation hardness by durometer method (Shore hardness) (ISO 48-4:2018, IDT)
MS ISO 48-4:2020
Status : Original
Format : PDF

This document specifies a method for determining the indentation hardness (Shore hardness) of
vulcanized or thermoplastic rubber using durometers with the following scales:
— the A scale ....Read more for rubbers in the normal-hardness range;
— the D scale for rubbers in the high-hardness range;
— the AO scale for rubbers in the low-hardness range and for cellular rubbers;
— the AM scale for thin rubber test pieces in the normal-hardness range. Close

RM 45.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • ...
  • 580
  • 581
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.