• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • Sign In
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Rubber and plastics test equipment - Tensile, flexural and compression types (constant rate of traverse) - Specification (First revision) (ISO 5893:2019, IDT)
MS ISO 5893:2020
Status : 1st Revision
Format : PDF

This document specifies requirements for tensile-testing systems operating at constant rate of traverse and suitable for testing rubbers, plastics and adhesives, although any one system might only be ....Read more applicable to a narrower range of materials. It also covers such systems when used for flexural, shear and compression tests. Close

RM 15.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized - Determination of adhesion to wire cord (Second revision) (ISO 5603:2017, IDT)
MS ISO 5603:2020
Status : 2nd Revision
Format : PDF

This document specifies two methods for determining the adhesion strength of vulcanized rubber to wire cord which is embedded in the rubber.
The two methods do not necessarily give the same resu ....Read more lts.
They are applicable primarily to test pieces prepared in the laboratory under standard conditions and used for the development and control of materials and processes utilized in the manufacture of products reinforced with wire cord.
NOTE The methods can also be used for single wire, for example bead wire.
Method 1 reduces the dependence of the measured adhesion on the modulus and strength properties of the rubber. Close

RM 45.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized or thermoplastic - Resistance to weathering (Second revision) (ISO 4665:2016, IDT)
MS ISO 4665:2020
Status : 2nd Revision
Format : PDF

This International Standard specifies methods for the exposure of vulcanized or thermoplastic rubbers
to natural or artificial weathering and methods for the determination of changes in colour, ....Read more appearance,
and physical properties resulting from exposure. Close

RM 30.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized or thermoplastic - Methods of test for staining in contact with organic material (Second revision) (ISO 3865:2020, IDT)
MS ISO 3865:2020
Status : 2nd Revision
Format : PDF

This document specifies three methods for estimating the staining of organic finishes (subsequently referred to as “organic material”) by vulcanized or thermoplastic rubber, as defined in Clause 3 ....Read more :
— method A: contact staining and migration staining;
— method B: extraction staining;
— method C: penetration staining; Close

RM 30.00

Document will be sent via email



 Add To Cart
Conducting and dissipative rubbers, vulcanized or thermoplastic - ICS: 83.060 © Copyright 2020 DEPARTMENT OF STANDARDS MALAYSIA Measurement of resistivity (Second revision) (ISO 1853:2018, IDT)
MS ISO 1853:2020
Status : 2nd Revision
Format : PDF

This document specifies the requirements for the laboratory testing of the volume resistivity of specially prepared test pieces of vulcanized or thermoplastic rubber compounds rendered conducting or d ....Read more issipative by the inclusion of carbon black or ionizable materials. The tests are suitable for materials with a resistivity of less than about 108 Ω⋅m.
Method 1 is the preferred method when test pieces with bonded electrodes are not available.
Method 2 is the preferred method when test pieces are moulded with the inclusion of bonded electrodes.
Method 3 is another method that can be used if the apparatus for method 1 or 2 is not available, but it has lower accuracy.
If a reference to this document is made without specifying the method, method 1 is used. Close

RM 30.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized or thermoplastic - Determination of flex cracking and crack growth (De Mattia) (Second revision) (ISO 132:2017, IDT)
MS ISO 132:2020
Status : 2nd Revision
Format : PDF

This document specifies a method of test intended for use in comparing the resistance of vulcanized or thermoplastic rubbers to the formation and growth of cracks, when subjected to repeated flexing o ....Read more n the De Mattia type machine. For determination of crack growth, an artificial cut is made in the testpiece to initiate cut growth. Close

RM 45.00

Document will be sent via email



 Add To Cart
Ceramic tiles – Definitions, classification, characteristics and marking (Second revision) (ISO 13006:2018, MOD)
MS ISO 13006:2020
Status : 2nd Revision
Format : PDF

This document defines terms and establishes classifications, characteristics and marking requirements for ceramic tiles of the best commercial quality (first quality). This document is not applicable ....Read more to tiles made by other than normal processes of extrusion or dry pressing. It is not applicable to decorative accessories or trim such as edges, corners, skirting, capping, coves, beads, steps, curved tiles and other accessory pieces or mosaics (i.e. any piece that can fit into a square, the side of which is less than 7 cm).
NOTE ISO 10545 (all parts) describes the test procedures required to determine the product characteristics listed in this document. ISO 10545 is a multi-part standard, each part describes a specific test procedure orrelated matter. Close

RM 90.00

Document will be sent via email



 Add To Cart
Risk management - Guidelines (First revision) (ISO 31000:2018, IDT)
MS ISO 31000:2020
Status : 1st Revision
Format : PDF

This document provides guidelines on managing risk faced by organizations. The application of these
guidelines can be customized to any organization and its context.
This document provides ....Read more a common approach to managing any type of risk and is not industry or sector
specific.
This document can be used throughout the life of the organization and can be applied to any activity,
including decision-making at all levels. Close

RM 45.00

Document will be sent via email



 Add To Cart
Information and documentation - Document storage requirements for archive and library materials (First revision) (ISO 11799:2015, IDT)
MS ISO 11799:2020
Status : 1st Revision
Format : PDF

This International Standard specifies the characteristics of repositories used for the long-term storage
of archive and library materials. It covers the siting and construction and renovation of ....Read more the building
and the installation and equipment to be used both within and around the building.
It applies to all archive and library materials held in repositories, where mixed media may be stored
together with paper-based materials. It does not preclude the establishment of separate areas or
compartments within individual repositories, where the environment can be controlled to create
conditions suitable for the needs of specific archive materials.
In a number of fields, national or local building regulations may encompass such matters as
construction, safety and security for public buildings and buildings in which valuable objects are stored
(fire precautions, emergency exits, security against earthquakes, theft, burglary, terrorist acts, etc.),
as well as services and equipment in professional use. This International Standard therefore avoids
detailed rules and regulations in these fields, except when recommending what may be additions to
these requirements. Close

RM 30.00

Document will be sent via email



 Add To Cart
Measurement of fluid flow in closed conduits - Ultrasonic transit-time meters for liquid
MS 2645:2020
Status : Original
Format : PDF

This Malaysian Standard specifies requirements and recommendations for ultrasonic liquid flowmeters, which utilize the transit time of ultrasonic signals to measure the flow of single-phase homogenous ....Read more liquids in closed conduits.
There are no limits on the minimum or maximum sizes of the meter.
This Malaysian Standard specifies performance, calibration and output characteristics of ultrasonic meters (USMs) for liquid flow measurement and deals with installation conditions. It covers installation with and without a dedicated proving (calibration) system. It covers both in-line and clamp-on transducers (used in configurations in which the beam is non-refracted and in those in which it is refracted). Included are both meters incorporating meter bodies and meters with field-mounted transducers. Close

RM 135.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • ...
  • 580
  • 581
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.