• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • Sign In
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Plastics - Preparation of test specimens by machining (ISO 2818:1994, IDT)
MS ISO 2818:1995 (CONFIRMED:2012)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard establishes the general principles and procedures to be followed when machining and notching test specimens from compression-moulded and injection-moulded plastics, extruded sh ....Read more eets, plates and partially finished or wholly finished products.

In Order to establish a basis for reproducible machining and notching conditions, the following general standardized conditions should be applied. lt is assumed, however, that the exact procedures to be used will be selected or specified by the relevant material specification or by the Standards on the particular test methods. If sufficiently detailed procedures are not thus specified, it is essential that the interested Parties agree on the conditions to be used. Close

RM 30.00

Document will be sent via email



 Add To Cart
RUBBER, VULCANIZED OR THERMOPLASTIC – DETERMINATION OF PERMEABILITY TO GASES (FIRST REVISION) (ISO 2782:2006, IDT)
MS ISO 2782:2007
Status : Original
Format : PDF

This Malaysian Standard describes two procedures for measuring the permeability of rubber to gases under steady-state conditions. One uses a horizontal measuring device for measurements at constant pr ....Read more essure and the other uses a vertical measuring device for measurements at constant volume or constant pressure. The results obtained by these procedures may be extrapolated to thicknesses of material different from that of the test piece, providing the rubber is homogeneous and isotropic.

The procedures apply to solid rubber of hardness not less than 35 IRHD and to gases such as air, nitrogen, oxygen, hydrogen, liquefied petroleum gas (in gaseous form) and coal gas. Errors may be introduced if the gas used appreciably swells the rubber under test. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



RUBBER, VULCANIZED OR THERMOPLASTIC - DETERMINATION OF DENSITY (FIRST REVISION) (ISO 2781:2008, IDT)
MS ISO 2781:2010
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies two methods of test for the determination of the density of solid vulcanized and thermoplastic rubbers.

Such determinations are of importance in the con ....Read more trol of the quality of a rubber compound and in the calculation of the mass of rubber required to produce a given volume of material.

This Malaysian Standard does not cover the determination of the relative density of rubber, which is the ratio of the mass of a given volume of rubber to the mass of an equal volume of pure water at a given temperature. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



BOARD - DETERMINATION OF BURSTING STRENGTH (ISO 2759:2001, IDT)
MS ISO 2759:2007
Status : Original
Format : PDF

This Malaysian Standard specifies a method for measuring the bursting strength of board submitted to increasing hydraulic pressure.It is applicable to all types of board (including corrugated and soli ....Read more d fibreboard) having bursting strengths within the range to . It is also applicable to papers or boards having bursting strengths as low as if the paper or board is to be used to prepare a material of higher bursting strength, such as corrugated board. In such cases, the measurements will not necessarily have the accuracy or precision stated for this method and it is necessary to include a note in the test report stating that the test gave results that were below the minimum value required by the method.

In the absence of any commercial agreement as to which method should be used for materials with bursting strengths between and , all materials with bursting strengths below , except components
of solid and corrugated fibreboard, should be tested by ISO 2758 and the remainder by this sta Close

RM 30.00

Document will be sent via email



 Add To Cart
PAPER - DETERMINATION OF BURSTING STRENGTH (ISO 2758:2001, IDT)
MS ISO 2758:2007
Status : Original
Format : PDF

This Malaysian Standard specifies a method for measuring the bursting strength of paper submitted to increasing hydraulic pressure. It is applicable to paper having bursting strengths within the range ....Read more 70 kPa 1 400 kPa. It is not intended to be used for the components (such as fluting medium or linerboard) of a combined board, for which the method given in ISO 2759 is more suitable.

In the absence of any commercial agreement as to which method should be used for testing the material, materials with bursting strengths below should be tested according to this standard. Close

RM 30.00

Document will be sent via email



 Add To Cart
Civil engineering - Standard method of measurement
MS 2701:2018
Status : Original
Format : PDF

This Malaysian Standard sets forth the procedure for measurement of the civil engineering work according to which the bill of quantities are to be prepared and priced.

This Malaysian Sta ....Read more ndard is to be used in conjunction with the conditions of contract for civil engineering work. It is applicable only for civil engineering work, simple building work, and mechanical and electrical work incidental to civil engineering work.

This standard does not deal with the preparation of the bill of quantities for complex mechanical and electrical engineering work, or complex building work or work which is seldom encountered in civil engineering contracts.

The use of other method of measurement not covered in this standard shall be stated in the preamble to the bill of quantities. Close

RM 45.00

Document will be sent via email



 Add To Cart
Landscape planting materials - Shrubs - Specification
MS 2700:2018
Status : Original
Format : PDF

This Malaysian Standard specifies requirements and methods of preparation for shrubs planting materials for landscape works. It is not applicable for bonsai or topiary.

RM 15.00

Document will be sent via email



 Add To Cart
Code of practice for medical lasers
MS 2699:2018
Status : Original
Format : PDF

This Malaysian Standard provides guidance for the safe application of lasers for medical purpose to ensure the protection of patients, public and healthcare professionals. This standard is also meant ....Read more to optimise overall safety and minimise possible hazards and exposure risks for all persons associated with medical laser usage. Close

RM 60.00

Document will be sent via email



 Add To Cart
Maintenance for lifts and escalators - Rules for maintenance instructions
MS 2698:2018
Status : Original
Format : PDF

This standard specifies the elements necessary for the preparation of the instructions for the maintenance operations, as in 3.1, which are provided for new installed passenger lifts, goods passenger ....Read more lifts, accessible goods only lifts, service lifts, escalators and moving walks.

This Malaysian Standard does not cover:
a) instructions for the installation and the dismantling;
b) any legal examinations and tests based on national regulations.

Existing installations are not covered by this standard, but it can be taken as a references. Close

RM 45.00

Document will be sent via email



 Add To Cart
Motor vehicle aftermarket - Repair, reuse, recycle and remanufacture (4R) for parts and components - Code of practice
MS 2697:2018
Status : Original
Format : PDF

This Malaysian Standard prescribes requirements for 4R activities of vehicles parts and components. This standard also covers aspects relating to knowledge, process and method, materials, equipment, s ....Read more afety and environment.

This standard applies to entities involved in 4R activities including material recovery, processing and handling for reuse, repair, recycle and remanufacture of vehicles parts and components. These licensed entities are also known as authorised treatment facilities (ATF). Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • ...
  • 580
  • 581
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.