• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • Sign In
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 1: Designation system and basis for specifications (First revision) (ISO 7391-1:2006, IDT)
MS ISO 7391-1:2012
Status : 1st Revision
Format : PDF

This Malaysian Standard establishes a system of designation for polycarbonate thermoplastic material, which may be used as the basis for specifications.The types of polycarbonate plastic are different ....Read more iated from each other by a classification system based on appropriate levels of the designatory properties: 
1. viscosity number
2. melt volume-flow rate
3. Charpy impact strength

and on information about the intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials.

This Malaysian Standard is applicable to thermoplastic polyesters of carbonic acid and aromatic dihydroxy compounds. The polyester may be a homopolymer, a copolymer or a mixture of the two.

It applies to materials ready for normal use in the form of powder, granules or pellets and to materials unmodified or modified by colorants, additives, fillers, etc. Close

RM 15.00

Document will be sent via email



 Add To Cart
PLASTICS – POLYCARBONATE (PC) MOULDING AND EXTRUSION MATERIALS – PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (FIRST REVISION) (ISO 7391-2:2006, IDT)
MS ISO 7391-2:2007
Status : Withdrawn
Format : PDF

This Malaysian Standards specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of polycarbonate moulding and extrusion materials. Require ....Read more ments for handling test material and for conditioning both the test material before moulding and the specimens before testing are given here. 
Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are given. Properties and test methods which are suitable and necessary to characterize polycarbonate moulding and extrusion materials are listed.

The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for or of particular significance to these moulding and extrusion materials are also included in this part of ISO 7391, as are the designatory properties specified in Part 1.

In order to obtain reproducible and comparable test results, it Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



Anaesthetic and respiratory equipment - Laryngoscopes for tracheal intubation (ISO 7376:2009, IDT)
MS ISO 7376:2011 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard gives general requirements for laryngoscopes used for intubation, and specifies critical dimensions for the handle and lamp of hook-on type laryngoscopes. It also addresses the ....Read more interchangeability of blades and handles. 
It is applicable only to instruments with an internal battery-operated power source for illuminating the larynx, since electrical safety requirements can be more stringent for instruments connected to mains or external power packs. Close

RM 60.00

Document will be sent via email



 Add To Cart
THERMAL INSULATION – PHYSICAL QUANTITIES AND DEFINITIONS (ISO 7345:1987, IDT)
MS ISO 7345 : 2003
Status : Original
Format : PDF

This Malaysian Standard defines physical quantities used in the field of thermal insulation, and gives the corresponding symbols and units.

RM 30.00

Document will be sent via email



 Add To Cart
RUBBER AND PLASTICS HOSES - ASSESSMENT OF OZONE RESISTANCE UNDER STATIC CONDITIONS (ISO 7326:2006, IDT)
MS ISO 7326:2007
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies five methods for determining the ozone resistance of the outer covers of hoses: 
-method 1, for bore sizes up to and including 25 mm, carried out on the hose ....Read more itself;
-method 2, for bore sizes greater than 25 mm, carried out on a test piece from the hose wall;
-method 3, for bore sizes greater than 25 mm, carried out on a test piece from the cover;
-method 4, for all bore sizes, carried out on the hose itself;
-method 5, for all bore sizes, carried out on hoses that are expandable, for example textile-reinforced hoses.

NOTE. For hoses with built-in fittings from which it is not possible to take test pieces, the ozone resistance may be assessed on slabs in accordance with ISO 1431-1, using test sheets of the appropriate polymeric compound vulcanized to the same degree. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



Corrugating medium - Determination of the flat crush resistance after laboratory fluting (First revision) (ISO 7263:2011, IDT)
MS ISO 7263:2012
Status : Original
Format : PDF

This Malaysian Standard specifies two methods for the determination of the flat crush resistance of a corrugating medium after laboratory fluting. 
The procedures are applicable to any corrugat ....Read more ing medium intended to be used, after fluting, in the
manufacture of corrugated board. Close

RM 30.00

Document will be sent via email



 Add To Cart
Basic human body measurements for technological design - Part 1: Body measurement definitions and landmarks (First revision) (ISO 7250-1:2008, IDT)
MS ISO 7250-1:2008 (CONFIRMED:2013)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard provides a description of anthropometric measurements which can be used as a basis for comparison of population groups. 
The basic list specified in this part of ISO 725 ....Read more 0 is intended to serve as a guide for ergonomists who are required to define population groups and apply their knowledge to the geometric design of the places where people work and live.

This list is not intended to serve as a guide for how to take anthropometric measurements, but it gives information to the ergonomist and designer on the anatomical and anthropometrical bases and principles of measurement which are applied in the solution of design tasks.

This Malaysian Standard is intended to be used in conjunction with national or international regulations or agreements to assure harmony in defining population groups. In its various applications, it is anticipated that the basic list will be supplemented by specific additional measurements. Close

RM 60.00

Document will be sent via email



 Add To Cart
BASIC HUMAN BODY MEASUREMENTS FOR TECHNOLOGICAL DESIGN(ISO 7250:1996, IDT)
MS ISO 7250:2003
Status : Original
Format : PDF

This Malaysian Standard provides a description of anthropometric measurements which can be used as a basis for comparison of population groups. 
The basic list specified in this standard is int ....Read more ended to serve as a guide for ergonomists who are required to define population groups and apply their knowledge to the geometric design of the places where people work and live.

This list is not intended to serve as a guide for how to take anthropometric measurements, but it gives in- formation to the ergonomist and designer on the anatomical and anthropometrical bases and principles of measurement which are applied in the solution of design tasks.

This Malaysian Standard may be used in conjunction with national or international regulations or agreements to assure harmony in defining population groups. In its various applications, it is anticipated that the basic list will be supplemented by specific additional measurements. Close

RM 45.00

Document will be sent via email



 Add To Cart
Rubber and plastics hoses and hose assemblies - Determination of resistance to vacuum (ISO 7233:2006, IDT)
MS ISO 7233:2008 (CONFIRMED:2013)
Status : Withdrawn
Format : PDF

This Malaysian Standard specifies three methods for determining the resistance to vacuum of hoses and hose assemblies manufactured from plastic or rubber. 
Applicable dimensions of hoses for e ....Read more ach method are as follows:
- method A — for hoses of nominal bore up to and including 80 mm;
- method B — for hoses of nominal bore greater than 80 mm;
- method C — for hoses of all dimensions.

Methods A and B can also be used to check the adhesion of the lining to the reinforcement (delamination) in a length of hard-wall hose or hose assembly. Close

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



GAS CYLINDERS – PRECAUTIONARY LABELS (ISO 7225:2005, IDT)
MS ISO 7225:2006
Status : Original
Format : PDF

This Malaysian Standard specifies the design, content (i.e. hazard symbols and text) and application of precautionary labels intended for use on individual gas cylinders containing single gases or gas ....Read more mixtures. Labels for cylinders of bundles and labels for bundles are not covered by this Malaysian Standard. Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • ...
  • 581
  • 582
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.