• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Thermal insulation products for buildings – Factory made mineral wool (MW) products – Specification (Second revision)
MS 1020:2022
Status : 2nd Revision
Format : PDF

This Malaysian Standard specifies the requirements for factory made mineral wool products, with or without facings, which are used for the thermal insulation of buildings. The products are manufacture ....Read more d in the form of rolls, batts, boards or slabs.

This document describes product characteristics are includes procedures for testing, evaluation of conformity, marking and labeling.

Products covered by this document are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered.

This document does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards.

Products with a declared thermal resistance lower than 0.6 m2K/W or a declared thermal conductivity greater than 0.050 W/(mK) at 20 C are not covered by this standard.

This document does not cover in situ insulation products and products intended to be used for the insulation of industrial installations. Close

RM 30.00

Document will be sent via email



 Add To Cart
Methods of testing cement – Part 7: Methods of taking and preparing samples of cement (First revision) (EN 196-7:2007)
MS EN 196-7:2022
Status : 1st Revision
Format : PDF

This European Standard describes the equipment to be used, the methods to be followed and the provisions for taking samples of cement, representative of given lots for testing, to assess the quality o ....Read more f products prior to, during or after delivery.

The provisions of this standard are only applicable when samples of cement are:

a) required for evaluating the conformity of a cement at any time with a standard; or
b) requested for checking a delivery or a lot with a standard, the provisions of a contract or the specification in an order.

The standard is applicable to the taking of samples of all types of cements defined by European Standards for cements whether they are:

c) contained in silos;
d) contained in bags, canisters, drums or any other packages;
e) transported in bulk in road vehicles, railway wagons, ships, etc.

NOTE The requirements of this standard can also, by agreement between the parties, be followed for acceptance inspections for all non-standardized hydraulic binders. Close

RM 30.00

Document will be sent via email

For sale within Malaysia Only

 Add To Cart
Vitrified clay pipes and fittings and pipe joints for drains and sewers - Part 3: Test methods (First revision)
MS 1061-3:2022
Status : 1st Revision
Format : PDF

This part of this Malaysian Standard specifies requirements for the test methods.

RM 75.00

Document will be sent via email



 Add To Cart
Vitrified clay pipes and fittings and pipe joints for drains and sewers - Part 2: Quality control and sampling (First revision)
MS 1061-2:2022
Status : 1st Revision
Format : PDF

This part of this Malaysian Standard specifies requirements for manufacturer’s internal quality control, third party assessment and inspection. It describes in detail, routine, regular, optional and ....Read more evaluation tests. In addition, it includes procedures and switching rules for inspection by variables.

NOTE. Where reference is made to clauses in MS 1061-1 and MS 1061-2 it is clearly stated. Close

RM 45.00

Document will be sent via email



 Add To Cart
Vitrified clay pipes and fittings and pipe joints for drains and sewers - Part 1: Requirements (Second revision)
MS 1061-1:2022
Status : 2nd Revision
Format : PDF

This Malaysian Standard specifies requirements for flexibly jointed vitrified clay pipes and fittings with or without sockets for the construction of drainage and sewerage systems. Although normally o ....Read more perated under gravity, the pipes and fittings covered by this standard will accept periodic hydraulic surcharge.

If pipes are required to withstand continuous working under low pressure, the pressure used in tests in this document shall be agreed between the manufacturer and the purchaser with a maximum test pressure of 600 kPa (6.0 bar).

The preferred dimensions for pipe lengths, curvature of bends and angles of junction arms are specified in this document. Other values for these dimensions are acceptable provided the products meet all the relevant performance requirements and are marked correctly. Fittings groups covered by this part of this standard are given in MS 1061: Part 2.

Where this document provides for different strength classes, different systems of jointing dimensions, different lengths and different fittings, the specifiers/purchasers may select according to their requirements. Close

RM 30.00

Document will be sent via email



 Add To Cart
Malaysia National Annex to MS EN 1991-1-6:2022, Eurocode 1 - Actions on structures Part 1-6: General actions - Actions during execution
MS EN 1991-1-6:2022 (NATIONAL ANNEX 2022)
Status : Original
Format : PDF

This National Annex gives:

a) the Malaysia decisions for the Nationally Determined Parameters described in the
following subclauses of MS EN 1991-1-6:2022:

1.1(3)< ....Read more br /> 2.2(4) Note 1*
3.1(1)P
3.1(5) Notes 1 and 2
3.1(7)
3.1(8) Note 1
3.3(2)
3.3(6)
4.9(6) Note 2
4.10(1)P
4.11.1(2) Table 4.1**
4.11.2(1) Note 2
4.12(1)P Note 2
4.12(2)
4.12(3)
4.13(2)
Annex A, A1.1(1) Note 2
Annex A, A1.3(2)
Annex A, A2.3(1) Note 1
Annex A, A2.4(2)
Annex A, A2.4(3)
Annex A, A2.5(2)
Annex A, A2.5(3) Note 1

* Note 2 (4) as in MS EN 1991-1-6:2022
** Note 4.11.1(1) Table 4.1 as in MS EN 1991-1-6:2022

b) the decisions on the status of MS EN 1991-1-6:2022 informative Annex B (see NA.3);

c) references to non-contradictory complementary information (see NA.4). Close

RM 15.00

Document will be sent via email

For sale within Malaysia Only

 Add To Cart
Eurocode 1 - Actions on structures Part 1-6: General actions - Actions during execution (EN 1991-1-6:2005)
MS EN 1991-1-6:2022
Status : Original
Format : PDF

(1) EN 1991-1-6 provides principles and general rules for the determination of actions which should be taken into account during the execution of buildings and civil engineering works.

....Read more (2) The following subjects are dealt with in this part of EN 1991.

Section 1 : General
Section 2 : Classification of actions
Section 3: Design situations and limit states
Section 4 : Representation of actions
Annex A1 : Supplementary rules for buildings (normative)
Annex A2 : Supplementary rules for bridges (normative)
Annex B : Actions on structures during alteration, reconstruction or demolition (informative)

(3) EN 1991-1-6 also gives rules for the determination of actions which may be used for the design of auxiliary con-
struction works as defined in 1.5, needed for the execution of buildings and civil engineering works. Close

RM 60.00

Document will be sent via email

For sale within Malaysia Only

 Add To Cart
Fine ceramics (advanced ceramics, advanced technical ceramics) – Test method for air purification performance of semiconducting photocatalytic materials – Part 1: Removal of nitric oxide (ISO 22197-1:2016, IDT) (First revision)
MS ISO 22197-1:2018 (CONFIRMED:2025)
Status : 1st Confirmation
Format : PDF

This document specifies a test method for the determination of the air-purification performance of materials that contain a photocatalyst or have photocatalytic films on the surface, usually made from ....Read more semiconducting metal oxides, such as titanium dioxide or other ceramic materials, by continuous exposure of a test piece to the model air pollutant under illumination with ultraviolet light. This document is intended for use with different kinds of materials, such as construction materials in flat sheet, board or plate shape, that are the basic forms of materials for various applications. This document also applies to materials in honeycomb-form and to plastic or paper materials if they contain ceramic microcrystals and composites. This document does not apply to powder or granular photocatalytic materials.

This test method is usually applicable to photocatalytic materials produced for air purification. This method is not suitable for the determination of other performance attributes of photocatalytic materials, i.e. decomposition of water contaminants, self-cleaning, antifogging and antibacterial actions. It concerns the removal of nitric oxide. Close

RM 30.00

Document will be sent via email



 Add To Cart
Fine ceramics (advanced ceramics, advanced technical ceramics) – Vocabulary (ISO 20507:2014, IDT) (First revision)
MS ISO 20507:2018 (CONFIRMED:2025)
Status : 1st Confirmation
Format : PDF

This International Standard is a vocabulary, which provides a list of terms and associated definitions typically used for fine ceramic (advanced ceramic, advanced technical ceramic) materials, product ....Read more s, applications, properties, and processes. This International Standard contains, in separate lists, those abbreviations which have found general acceptance in the scientific and technical literature; they are given together with the corresponding terms and definitions or descriptions.

In this International Standard, the terms are defined using the term “fine ceramic”. The definitions apply equally to “advanced ceramics” and “advanced technical ceramics”, which are considered to be equivalent.

This International Standard does not include terms which, though used in the field of fine ceramics, are of a more general nature and are also well known in other fields of technology. Close

RM 60.00

Document will be sent via email



 Add To Cart
Fine ceramics (advanced ceramics, advanced technical ceramics) – Test method for linear thermal expansion of monolithic ceramics by push-rod technique (ISO 17562:2016, IDT) (First revision)
MS ISO 17562:2018 (CONFIRMED:2025)
Status : 1st Confirmation
Format : PDF

This International Standard specifies a method for the determination of the linear thermal expansion and the linear thermal expansion coefficient of monolithic ceramics from near liquid nitrogen tempe ....Read more rature up to a maximum temperature of 2 000 °C. Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • ...
  • 580
  • 581
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.