• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • Sign In
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




METEOROLOGY – SONIC ANEMOMETERS/ THERMOMETERS – ACCEPTANCE TEST METHODS FOR MEAN WIND MEASUREMENTS (ISO 16622:2002, IDT)
MS ISO 16622:2007 (CONFIRMED:2023)
Status : 2nd Confirmation
Format : PDF

This Malaysian Standard defines test methods of the performance of sonic anemometers/thermometers which employ the inverse time measurement for velocity of sound along differently oriented paths. It i ....Read more s applicable to designs measuring two or three components of the wind vector within an unlimited (360°) azimuthal acceptance angle. Close

RM 45.00

Document will be sent via email



 Add To Cart
Clothing for protection against contact with blood and body fluids - Determination of resistance of protective clothing materials to penetration by blood-borne pathogens - Test method using Phi-X174 bacteriophage (ISO 16604:2004, IDT)
MS ISO 16604:2011 (CONFIRMED:2022)
Status : 2nd Confirmation
Format : PDF

This Malaysian Standard describes a laboratory test method for measuring the resistance of materials used in protective clothing to penetration by blood-borne pathogens. This test method uses a surrog ....Read more ate microbe under conditions of continuous liquid contact. Protective clothing "pass/fail" determinations are based on the detection of viral penetration at a specific hydrostatic pressure using the ISO 13994 test apparatus.

This test method is not always effective in testing protective clothing materials having thick, inner liners which readily absorb the challenge fluid.

This test method involves a sensitive assay procedure. Because of the length of time required to complete this test method, it might not be suitable for use as a material or protective clothing quality control or assurance procedure. Close

RM 45.00

Document will be sent via email



 Add To Cart
Clothing for protection against contact with blood and body fluids - Determination of the resistance of protective clothing materials to penetration by blood and body fluids - Test method using synthetic blood (ISO 16603:2004, IDT)
MS ISO 16603:2011 (CONFIRMED:2022)
Status : 2nd Confirmation
Format : PDF

This Malaysian Standard describes a laboratory test method for measuring the penetration resistance of clothing materials to blood and body fluids. This test method uses a synthetic blood in continuou ....Read more s contact with the material specimen at specified set of conditions using the ISO 13994 test apparatus.

This test method is not always effective in testing protective clothing materials having thick, inner liners which readily absorb the synthetic blood. Close

RM 30.00

Document will be sent via email



 Add To Cart
ANIMAL FEEDING STUFFS - DETERMINATIONOF AMYLASE-TREATED NEUTRAL DETERGENT FIBRE CONTENT (aNDF) (ISO 16472:2006, IDT)
MS ISO 16472:2007
Status : Original
Format : PDF

This Malaysian Standard specifies methods for the determination of amylase-treated neutral detergent insoluble fibrous residue content in all types of animal feed.

NOT FOR SALE

"Please contact us if you are interested to purchase for reference."



Implants for surgery - Measurements of open-circuit potential to assess corrosion behaviour of metallic implantable materials and medical devices over extended time periods (ISO 16429:2004, IDT)
MS ISO 16429:2011 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies a test method for measurements over extended time periods of the open circuit potential of implant materials and surgically implantable devices immersed in a test env ....Read more ironment related to body fluid, using a standard corrosion test cell to study the electrochemical corrosion properties of the devices.

This method of monitoring the open-circuit potential can also be combined with mechanical static or dynamic loading tests.

This standard is applicable in particular to metallic materials which form passive layers with protective properties against corrosion, as typical for surgical implant materials.

This test method is intended for the investigation of single metallic materials or alloys. Close

RM 30.00

Document will be sent via email



 Add To Cart
AMBIENT AIR - DETERMINATION OF PARTICLE-PHASE POLYCYCLIC AROMATIC HYDROCARBONS BY HIGH PERFORMANCE LIQUID CHROMATOGRAPHY (ISO 16362:2005, IDT)
MS ISO 16362:2007 (CONFIRMED:2023)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies sampling, clean-up and analysis procedures for the quantitative determination of low volatility (particle-bound) polycyclic aromatic hydrocarbons (PAHs) in ambient ai ....Read more r. For sampling, a low-volume or a medium/high-volume sampling device may be used. Sampling times between 1 h and 24 h are possible. The sampling volume flowrates can range from 1 m3/h to 4 m3/h (“low volume sampler”) or from 10 m3/h to about 90 m3/h (“medium/high-volume sampler”). In any case, the linear face velocity at the collection filter should range between about 0,5 m/s and 0,9 m/s.

The method has been validated for sampling periods up to 24 h. The detection limits for single PAHs and the standard deviations resulting from duplicate measurements are listed in 9.2 and Annex D respectively.

This Malaysian Standard describes a sampling and analysis procedure for PAH that involves collection from air onto a filter followed by analysis using high performance liquid chromatography u Close

RM 60.00

Document will be sent via email



 Add To Cart
HEAVY COMMERCIAL VEHICLES AND BUSES - STEADY-STATE ROLLOVER THRESHOLD - TILT-TABLE TEST METHOD (ISO 16333:2004, IDT)
MS ISO 16333:2008
Status : Original
Format : PDF

This Malaysian Standard specifies a tilt-table test method for estimating the steady-state rollover threshold of a heavy commercial vehicle or bus, i.e. the maximum lateral acceleration that the test ....Read more vehicle could sustain in steady-state turning without rolling over.
It is applicable to complete roll units/combinations of roll-coupled vehicle units — e.g. single-unit vehicles, tractor–semitrailer combinations, articulated buses, full trailers, B-train combinations — of commercial vehicles, commercial vehicle combinations, buses or articulated buses as defined in ISO 3833, and under Categories M3, N2, N3, O3 and O4 of ECE and EC vehicle regulations (trucks and trailers with maximum weights above 3,5 t and buses and articulated buses with maximum weights above 5 t). It does not cover transient, vibratory or dynamic rollover situations; nor does it consider the influences of dynamic stability control systems. Furthermore, the quality of the estimate of the steady-state rollover threshol Close

RM 45.00

Document will be sent via email



 Add To Cart
Statistical interpretation of data - Part 7: median - Estimation and confidence intervals (ISO 16269-7:2001, IDT)
MS ISO 16269-7:2004 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies the procedures for establishing a point estimate and confidence intervals for the median of any continuous probability distribution of a population, based on a random ....Read more sample size from the population. These procedures are distribution-free, i.e. they do not require knowledge of the family of distributions to which the population distribution belongs. Similar procedures can be applied to estimate quartiles and percentiles.

NOTE: The median is the second quartile and the fiftieth percentile. Similar procedures for other quartiles or percentiles are not described in this part of ISO 16269. Close

RM 30.00

Document will be sent via email



 Add To Cart
Statistical interpretation of data - Part 4: Detection and treatment of outliers (ISO 16269-4:2010, IDT) (Published by STANDARDS MALAYSIA in 2012)
MS ISO 16269-4:2010 (CONFIRMED:2023)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard provides detailed descriptions of sound statistical testing procedures and graphical data analysis methods for detecting outliers in data obtained from measurement processes. I ....Read more t recommends sound robust estimation and testing procedures to accommodate the presence of outliers.

This Malaysian Standard is primarily designed for the detection and accommodation of outlier(s) from univariate data. Some guidance is provided for multivariate and regression data. Close

RM 90.00

Document will be sent via email



 Add To Cart
STATISTICAL INTERPRETATION OF DATA - PART 6: DETERMINATION OF STATISTICAL TOLERANCE INTERVALS (FIRST REVISION)(ISO 16269-6:2005, IDT)(PUBLISHED BY STANDARDS MALAYSIA IN 2010)
MS ISO 16269-6:2005
Status : 1st Revision
Format : PDF

This part of ISO 16269 describes procedures for establishing tolerance intervals that include at least a
specified proportion of the population with a specified confidence level. Both one-sided ....Read more and two-sided
statistical tolerance intervals are provided, a one-sided interval having either an upper or a lower limit while a two-sided interval has both upper and lower limits. Two methods are provided, a parametric method for the case where the characteristic being studied has a normal distribution and a distribution-free method for the case where nothing is known about the distribution except that it is continuous. Close

RM 60.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • ...
  • 581
  • 582
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.