• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Safety in laboratories - Code of practice - Part 2: Chemical aspects (Second revision)
MS 1042-2:2023
Status : 2nd Revision
Format : PDF

This Malaysian Standard sets out requirements and recommended procedures for safe working practices in the handling of chemicals in laboratories particularly for handling flammable, toxic, corrosive, ....Read more unstable and highly reactive chemicals and makes reference to the handling of compressed and liquefied gases. The standard also includes information on hazards associated with the handling of chemicals in laboratories.

This document is intended to be used in conjunction with MS 1042: Part 1, which provides requirements and recommendations on matters common to all types of laboratory work. If the requirements of any part of this document conflicts with any Malaysian regulations (Federal or State), the appropriate statutory regulations shall apply. Close

RM 105.00

Document will be sent via email



 Add To Cart
Gaseous fire extinguishing systems - Physical properties and system design - Part 5: FK-5-1-12 extinguishant (ISO 14520-5:2019, MOD)
MS 1746-5:2023
Status : Original
Format : PDF

This document contains specific requirements for gaseous fire-extinguishing systems, with respect to FK-5-1-12 extinguishant. It includes details of physical properties, specifications, usage and safe ....Read more ty aspects.

This document is applicable only to systems operating at nominal pressures of 25 bar, 34,5 bar, 42 bar and 50 bar with nitrogen propellant. This does not preclude the use of other systems. Close

RM 30.00

Document will be sent via email



 Add To Cart
Protective helmets and visors for vehicle users - Specification - Part 1: Protective helmets (Fourth revision)
MS 1-1:2023
Status : 4th Revision
Format : PDF

This Malaysian Standard specifies the minimum performance criteria and test requirements for protective helmets for vehicle users. This standard is written with particular reference to motorcyclists ( ....Read more rider and pillion). Close

RM 75.00

Document will be sent via email



 Add To Cart
Fresh lettuces (Lactuca sativa L.) - Specification (First revision)
MS 1361:2023
Status : 1st Revision
Format : PDF

This Malaysian Standard prescribes the requirements for fresh lettuces (Lactuca sativa L.) of the Asteraceae Syn. Compositae family to be supplied fresh to consumers. Lettuce for processing is exclude ....Read more d.

List of lettuce varieties are (see Annex A):

a) Lactuca sativa L. var. capitata (head lettuces including crisphead or iceberg and butterhead);
b) Lactuca sativa L. var. longifolia (cos or romaine lettuces); and
c) Lactuca sativa L. var. crispa (looseleaf lettuces).

NOTE. Name of produce in reference to MS 325. Close

RM 30.00

Document will be sent via email



 Add To Cart
Stainless steels for general purposes - Part 2: Corrosion-resistant semi-finished products, bars, rods and sections (First revision) (ISO 16143-2:2004, MOD)
MS 2240-2:2023
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies the technical delivery conditions for semi-finished products, hot formed bars, rods, and sections for general purposes made of the most important corrosion-resistant ....Read more stainless steel grades.

NOTES:
1. Through this part of ISO 16143, the term “general purposes” other than the special purposes mentioned in the bibliography.

2. Heat-resistant steel grades can be found in ISO 4955 and they can be used for corrosion-resistant purposes.

In addition to this part of ISO 16143, the general technical delivery requirements of MS 1846 are applicable.

This part of ISO 16143 does not apply to components manufactured by further processing the product forms listed in the first paragraph above with quality characteristics altered as a result of such further processing. Close

RM 75.00

Document will be sent via email



 Add To Cart
Tinplate and blackplate - Specification (Second revision)
MS 1076:2023
Status : 2nd Revision
Format : PDF

This Malaysian Standard draft specifies requirements for single and double cold-reduced blackplates and electrolytic tinplates in the form of sheets or coils that are intended mainly for food can, bev ....Read more erage can, and general use.

NOTE. The term ‘blackplates’ refer to the steel sheets and steel strips, prior to coating, to be used to make tinplates or tin-free steel, which are sometimes traded as they are. Close

RM 60.00

Document will be sent via email



 Add To Cart
Glass-fibre reinforced polyester panels and panel water tanks - Part 1: Specification (Second revision)
MS 1390-1:2023
Status : 2nd Revision
Format : PDF

This Malaysian Standard specifies requirements for glass-fibre reinforced polyester panels used in the construction of panel water tank for the sanitary storage of potable water. It is called GRP pane ....Read more l water tanks hereafter.

NOTE. GRP is also termed as fibreglass reinforced polyester (FRP) in this standard. Close

RM 75.00

Document will be sent via email



 Add To Cart
Polyethylene (PE) piping systems for water supply and for drainage and sewerage under pressure - Part 7: Guidance for the assessment of conformity (First revision)
MS 1058-7:2023
Status : 1st Revision
Format : PDF

This part of Malaysian Standard gives guidance for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of MS 1058 intended to be includ ....Read more ed in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.

It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to MS ISO 9001.

NOTE. If certification is involved, the certification and inspection body is preferably compliant with MS ISO/IEC 17065, MS ISO/IEC 1702 or MS ISO/IEC 17020 as applicable. Close

RM 60.00

Document will be sent via email



 Add To Cart
Polyethylene (PE) piping systems for water supply and for drainage and sewerage under pressure - Part 5: Fitness for purpose of the system (First revision)
MS 1058-5:2023
Status : 1st Revision
Format : PDF

This part of Malaysian Standard specifies the characteristics of the fitness for purpose of pipes and/or fittings assemblies made from polyethylene (PE) for buried or above ground applications, intend ....Read more ed for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes. Close

RM 30.00

Document will be sent via email



 Add To Cart
Polyethylene (PE) piping systems for water supply and for drainage and sewerage under pressure - Part 3: Fittings (First revision)
MS 1058-3:2023
Status : 1st Revision
Format : PDF

This part of Malaysian Standard specifies the characteristics of fittings made from polyethylene (PE) intended for the conveyance of water for human consumption, raw water prior to treatment, drainage ....Read more and sewerage under pressure, vacuum sewer systems, and water for other purposes.

NOTE. For PE components intended for the conveyance of water intended for human consumption and raw water prior to treatment attention is drawn to Clause 5.6 of this Malaysian Standard. Components manufactured for water for other purposes, drainage and sewerage may not be suitable for water supply for human consumption. Close

RM 75.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • ...
  • 580
  • 581
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.