• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




LATEX EMULSION PAINT FOR EXTERIORAND INTERIOR USE – SPECIFICATION (THIRD REVISION)
MS 134:2007
Status : 3rd Revision
Format : PDF

This Malaysian Standard specifies an air-drying latex emulsion paint including textured finish suitable for exterior and interior use on masonry surfaces including concrete, brick, stucco, concrete bl ....Read more ock and asbestos cement shingles and sidings, and for recoating of previously painted surface provided the surface is in sound condition and suitable for receiving such a coating. It may also be used on suitably primed metal and wood surfaces.

NOTE. Paints specifically for interior use only are covered by MS 903:1984, Specification for latex emulsion paint for interior use. Close

RM 15.00

Document will be sent via email



 Add To Cart
Paints and varnishes - Part E10: Pull-off test for adhesion (First revision) (ISO 4624:2002, MOD)
MS 133-E10:2012
Status : 1st Revision
Format : PDF

This International Standard describes methods for determining the adhesion by carrying out a pull-off test on a single
coating or a multi-coat system of paint, varnish or related product.
....Read more These test methods have been found useful in comparing the adhesion behaviour of different coatings. It is most
useful in providing relative ratings for a series of coated panels exhibiting significant differences in adhesion.
The test may be applied using a wide range of substrates. Different procedures are given according to whether the
substrate is deformable, for example thin metal, plastics and wood, or rigid, for example thick concrete and metal
plates. For special purposes, the coating may be applied directly to the face of a test dolly. Close

RM 30.00

Document will be sent via email



 Add To Cart
METHODS OF TEST FOR PAINTS AND VARNISHES : PART F2 : RESISTANCE TO HUMIDITY (CONTINUOUS CONDENSATION) (FIRST REVISION) (ISO 6270:1980, MOD)
MS 133 : PART F2 : 2002
Status : Withdrawn
Format : PDF

1.1 This Malaysian Standard specifies a method for determining the resistance of paint
films, paints systems and allied products to conditions of high humidity.
t2 The method is applicable ....Read more to coatings both on porous substrates such as wood,
plaster and plasterboard, and on non-porous substrates such as metal. It provides an
indication of performance likely to be obtained under severe conditions of exposure where
continuous condensation occurs on the surface.
t3 The procedure may reveal failures of the coating (including blistering, staining,
softening, wrinkling and embrittlement) and deterioration of the substrate. Close

NOT FOR SALE

Please contact us if you are interested to purchase for reference.



SPECIFICATION FOR GLOSS ENAMEL PAINT (SECOND REVISION)
MS 125:1995, AMD. 1:1997
Status : 2nd Revision
Format : PDF

This Malaysian Standard specifies an air-drying gloss paint for use on primed interior and exterior wood and metal surfaces and for recoating of previou ....Read more sly painted surfaces,provided the surface is in sound condition and suitable for receiving such a coating. Close

FREE

Document will be sent via email



Please Login to enable MS to be send via email
SPECIFICATION FOR GLOSS ENAMEL PAINT (SECOND REVISION)
MS 125:1995
Status : 2nd Revision
Format : PDF

This Malaysian Standard specifies an air-drying gloss paint for use on primed interior and
exterior wood and metal surfaces and for recoating of p ....Read more reviously painted surfaces,
provided the surface is in sound condition and suitable for receiving such a coating. Close

RM 15.00

Document will be sent via email



 Add To Cart
Plywood - Specification (Second revision)
MS 228:2015
Status : 2nd Revision
Format : PDF

1.1 This Malaysian Standard specified requirements for plywood for general and structural
use, in dry, tropical dry/humid and high humidity/exteri ....Read more or conditions. This standard includes
requirements for the quality of veneer, glue bond, lay-up (construction), dimensions and
tolerances, conformance verification (where applicable) and marking.
1.2 The values listed in this standard relate to product properties, but these are not
characteristic values to be used in design calculations.
NOTE. Such characteristic values are given by the manufacturer, based on testing according to ISO
16572. Additional information on supplementary properties for certain applications is also given. Close

RM 30.00

Document will be sent via email



 Add To Cart
wooden windows - Specifications
MS 2620:2015 (CONFIRMED:2020)
Status : 1st Confirmation
Format : PDF

1.1 This Malaysian Standard specifies requirements for wooden window frames, box frame windows and their sashes incorporating traditional component sect ....Read more ions.

1.2 It does not apply to window assemblies intended to carry loads transmitted from the structure into which they are fitted.

1.3 The concept of modular coordination is incorporated in this standard in order to
harmonise with MS 1064.

1.4 Effort is made to classify windows into three categories of Deluxe, Regular and
Economy in line with current pattern of utilisation in the country.

1.5 Minimum dimension is also proposed for certain components used for each category with the aim to complement the harmonisation effort made. Close

RM 30.00

Document will be sent via email



 Add To Cart
Palm plywood - Specification
MS 2629:2018 (CONFIRMED:2025)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies requirements for plywood for general, furniture and structural use, in dry, tropical-dry/humid and high-humidity/exter ....Read more ior conditions. This standard includes requirements for the quality of veneer, glue-bond, lay-up (construction), dimensions and tolerances, conformance verification (where applicable) and marking. Additional information on supplementary properties for certain applications is also provided. Close

RM 30.00

Document will be sent via email



 Add To Cart
Natural fibre-plastic composite (NFPC) -Test method - Part 2: Decking profiles and tiles
MS 2630:2018
Status : Original
Format : PDF

This Malaysian Standard provides test methods of natural fibre-plastic composite (NFPC), usually called wood-plastic composite (WPC), for decking profil ....Read more es and tiles used in exterior applications. This part of standard will cover the preparation of specimen, test equipment, procedures of measurements and evaluation methods. Close

RM 45.00

Document will be sent via email



 Add To Cart
Pencils - Specification (First revision)
MS 1159:2009 (CONFIRMED:2014)
Status : 1st Revision
Format : PDF

This Malaysian Standard specifies requirements and test methods for wooden-cased black
lead pencils primarily intended for writing, drafting and d ....Read more rawing purposes. Close

RM 15.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.