GLOSSARY OF TERMS RELATING TO TIMBER AND wood-BASED PANEL PRODUCTS: PART 2: wood-BASED PANEL PRODUCTS
MS 471: PART 2:2003Status : Original
Format : PDF
This Malaysian Standard is intended to provide uniformity in the definitions of the terms used in the Malaysian timber industry. This standard deals with wood< ....Read more
GLOSSARY OF TERMS RELATING TO TIMBER AND wood-BASED PANEL PRODUCTS: PART 3: CARPENTRY, JOINERY AND FURNITURE
MS 471: PART 3:2003 (CONFIRMED:2024)Status : 1st Confirmation
Format : PDF
This Malaysian Standard is intended to provide uniformity in the definitions of the terms used in the Malaysian timber industry. This standard deals with carpentry, joinery and furniture.
GLOSSARY OF TERMS RELATING TO TIMBER AND wood-BASED PANEL PRODUCTS : PART 1 : CHARACTERISTICS AND PROPERTIES OF TIMBER (FIRST REVISION)
MS 471 : PART 1 : 2001 (CONFIRMED:2024)Status : 1st Confirmation
Format : PDF
This Malaysian Standard is intended to provide uniformity in the definitions of the terms used in the Malaysian timber industry. This part deals with characteristics and properties of timber, includin ....Read more
SPECIFICATION FOR SINGLE PACK VARNISHES FOR woodEN PANELLING
MS 432:1976 (CONFIRMED:2020)Status : 1st Confirmation
Format : PDF
This Malaysian Standard specified requirements for a single pack varnish for use as a transparent or a semi-transparent surface coating on wooden panell ....Read more
TREATMENT OF TIMBER WITH COPPER/CHROME/ARSENIC wood PRESERVATIVES – SPECIFICATION (THIRD REVISION)
MS 360:2006 (CONFIRMED:2020)Status : 1st Confirmation
Format : PDF
This Malaysian Standard specifies requirements for treatment of timber with water-borne
copper/chrome/arsenic (CCA) wood preservative formulation ....Read more
SPECIFICATION FOR PAINT, VARNISH AND LACQUER REMOVER, SOLVENT TYPE, NONFLAMMABLE (FIRST REVISION)
MS 291 : 1984Status : Original
Format : PDF
This Malaysian Standard specifies requirements for a paint, varnish and lacquer remover, commonly employed in scrape-off operations suitable for use on finished and metal surfaces. The material may not, however, be suitable for use on some plastic surfaces.The material is intended to be applied tothe painted, varnished or lacquered surface by brushing and allowing to remain undisturbed until the paint, varnish or lacquer film has been softened. It is subsequently removed, together with the residue of the paint, varnish or lacquer film, by scraping, followed bywashing with water or a suitable solvent such as white spirit.Certain types of coatings such as some stoved, cold-cured, or polymeric materials, may not be readily acted upon by the materials covered by this specification; for removing such special coatings. manufacturers should be asked to supply removers appropriate to the specific case but these may not necessarily conform to this specification.
SPECIFICATION FOR ALUMINIUM FINISHING PAINT (FIRST REVISION)
MS 289 : 1987 (CONFIRMED:2020)Status : 1st Confirmation
Format : PDF
This Malaysian Standard specifies an air drying aluminium finishing paint for use on primed interior and exterior wood and metal surfaces, and for recoa ....Read more
SPECIFICATION FOR MATCHES (FIRST REVISION)
MS 245:2004Status : 1st Revision
Format : PDF
This Malaysian Standard specifies the requirements and tests for the following types of matches:
a) 'Safety' wood matches in boxes.
b) 'Safe ....Read more
SPECIFICATION FOR MATCHES
MS 245 : 1974Status : Original
Format : PDF
This Malaysian Standard prescribes the requirements and tests for the following types of matches: (a) 'Safety' wood matches in boxes; (b) 'Safety' ....Read more and paper matches in books. (The width of the covers shall not exceed 83 mm).
SPECIFICATION FOR ALUMINIUM wood PRIMER (FIRST REVISION)
MS 162 : 1987Status : 1st Revision
Format : PDF
This Malaysian Standard specifies requirements for a suitable paint for use as a primer on wood surfaces.