ROAD vehicleS - ALTERNATORS WITH REGULATORS - TEST METHODS AND GENERAL REQUIREMENTS (FIRST REVISION) (ISO 8854:1988, IDT)
MS ISO 8854:2009Status : 1st Revision
Format : PDF
The adoption of the ISO Standard as a Malaysian Standard was recommended by the Technical Committee on Electrical and Electronic Equipment under the authority of the Industry Standards Committee on Ro ....Read more
RUBBER HOSES AND HOSE ASSEMBLIES FOR LIQUEFIED PETROLEUM GAS IN MOTOR vehicleS - SPECIFICATION (ISO 8789:1994, IDT)
MS ISO 8789:2005Status : Original
Format : PDF
This Malaysian Standard specifies the requirements for rubber hoses and hose assemblies, up to a maximum bore of 20 mm, for use in motor vehicles with l ....Read more
Commercial road vehicles - 40 mm drawbar eye - Interchangeability (ISO 8755:2001, IDT)
MS ISO 8755:2007 (CONFIRMED:2016)Status : 1st Confirmation
Format : PDF
This Malaysian Standard specifies the characteristics of 40 mm drawbar eyes, necessary for the interchangeability of the coupling components on trailers and permitting interchangeability between towin ....Read more
Road vehicles – Connections for on board electrical wiring harnesses - Part 2: Definitions, test methods and general performance requirements (ISO 8092-2:2000, IDT)
MS ISO 8092-2:2005 (CONFIRMED:2012)Status : 1st Confirmation
Format : PDF
This Malaysian Standard defines terms and specifies test methods and general performance requirements for single-and multi-pole connections used with on-board electrical wiring harnesses in road ....Read more
s.
This Malaysian Standard is applicable to connect or designed to be disconnected after mounting in the vehicle for repair and maintenance only.It does not cover one-part connections,i.e.where one part of the connection has direct contact with the pattern of the printed circuit board.
This Malaysian Standard is not applicable to the internal connections of electronic devices.
Road vehicles - Connections for on board electrical wiring harnesses - Part 1: Tabs for single-pole connections - Dimensions and specific requirements (ISO 8092-1:1996, IDT)
MS ISO 8092-1:2005 (CONFIRMED:2012)Status : 1st Confirmation
Format : PDF
This Malaysian Standard specifies dimensions for the tabs of single-pole connections and specific requirements, for on-board electrical wiring harnesses of road s, which can be fitted into female contacts. It applies to connectors designed to be disconnected after mounting in the vehicle for the purposes of repair and/or maintenance only.
ROAD vehicleS - CONNECTIONS FOR ON-BOARD ELECTRICAL WIRING HARNESSES - PART 4: PINS FOR SINGLE- AND MULTI-POLE CONNECTIONS - DIMENSIONS AND SPECIFIC REQUIREMENTS (ISO 8092-4:1997, IDT)
MS ISO 8092-4:2009Status : Original
Format : PDF
This Malaysian Standard specifies dimensions for the pins of single- and multi-pole connections and specific requirements, for on-board electrical wiring harnesses of road s. It applies to connections designed to be disconnected after mounting in the vehicle in the case of repair and/or maintenance only.
ROAD vehicleS - CONNECTIONS FOR ON-BOARD ELECTRICAL WIRING HARNESSES - PART 3: TABS FOR MULTI-POLE CONNECTIONS - DIMENSIONS AND SPECIFIC REQUIREMENTS (ISO 8092-3:1996, IDT)
MS ISO 8092-3:2009Status : Original
Format : PDF
This Malaysian Standard specifies dimensions for the tabs of multi-pole connections and specific requirements, for on-board electrical wiring harnesses of road ....Read more s. It applies to connections designed to be disconnected after mounting in the vehicle for the purposes of repair and/or maintenance only.
ROAD vehicleS – CONNECTIONS FOR ON BOARD ELECTRICAL WIRING HARNESSES PART 2: DEFINITIONS, TEST METHODS AND GENERAL PERFORMANCE REQUIREMENTS (ISO 8092-2:2000, IDT)
MS ISO 8092-2:2005Status : Original
Format : PDF
This Malaysian Standard define sterms and specifies test methods and general performance requirements for single-and multi-pole connections used with on-board electrical wiring harnesses in road ....Read more
s.
This standard is applicable to connectors designed to be disconnected after mounting in the vehicle for repair and maintenance only. It does not cover one-part connections, i.e.where one part of the connection has direct contact with the pattern of the printed circuit board.
This standard is not applicable to the internal connections of electronic devices.
Wheelchairs - Part 19: Wheeled mobility devices for use as seats in motor vehicles (ISO 7176-19:2008, IDT)
MS ISO 7176-19:2010 (CONFIRMED:2015)Status : 1st Confirmation
Format : PDF
This Malaysian Standard applies to all manual and powered wheelchairs, including scooters, which, in addition to their primary function as wheeled mobility devices, are also likely to be used as forwa ....Read more
Wheelchairs - Part 21: Requirements and test methods for electromagnetic compatibility of electrically powered wheelchairs and scooters, and battery chargers (ISO 7176-21:2009, IDT)
MS ISO 7176-21:2010 (CONFIRMED:2015)Status : 1st Confirmation
Format : PDF
This Malaysian Standard specifies requirements and test methods for electromagnetic emissions and for electromagnetic immunity of electrically powered wheelchairs and scooters with a maximum speed of ....Read more